RF solutions SWITCHLINK-8S1 Remote Control System User Guide
- June 10, 2024
- RF SOLUTIONS
Table of Contents
SWITCHLINK-8S1 Remote Control System
Quick Start Guide
PART NO.
SWITCHLINK-8S1
SWITCHLINK Remote Control System
Simplified Declaration of Conformity (RED)
Hereby, RF Solutions Limited declares that the radio equipment type defined
within this document is in compliance with Directive 2014/53/EU. The full text
of
the EU declaration of conformity is available at the following internet
address: www.rfsolutions.co.uk
RF Solutions Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT Discard with normal waste, please recycle.
ROHS Directive 2011/65/EU and amendment 2015/863/EU
Specifies certain limits for hazardous substances.
WEEE Directive 2012/19/EU
Waste electrical & electronic equipment. This product must be disposed of
through a licensed WEEE collection point. RF
Solutions Ltd., fulfils its WEEE obligations by membership of an approved
compliance scheme.
Environment agency number: WEE/JB0104WV.
Waste Batteries and Accumulators Directive
2006/66/EC
Where batteries are fitted, before recycling the
product, the batteries must be removed and disposed
of at a licensed collection point. RF Solutions battery
producer number: BPRN00060.
Disclaimer:
Whilst the information in this document is believed to be correct at the time
of issue, RF Solutions Ltd does not accept any liability whatsoever
for its accuracy, adequacy or completeness. No express or implied warranty or
representation is given relating to the information contained in
this document. RF Solutions Ltd reserves the right to make changes and
improvements to the product(s) described herein without notice. Buyers
and other users should determine for themselves the suitability of any such
information or products for their own particular requirements or
specification(s). RF Solutions Ltd shall not be liable for any loss or damage
caused as a result of user’s own determination of how to deploy or
use RF Solutions Ltd’s products. Use of RF Solutions Ltd products or
components in life support and/or safety applications is not authorised
except with express written approval. No licences are created, implicitly or
otherwise, under any of RF Solutions Ltd’s intel lectual property
rights. Liability for loss or damage resulting or caused by reliance on the
information contained herein or from the use of the product (including
liability resulting from negligence or where RF Solutions Ltd was aware of the
possibility of such loss or damage arising) is excluded. This will not
operate to limit or restrict RF Solutions Ltd’s liability for death or
personal injury resulting from its negligence.
SWITCHLINK Remote Control System
Safety Information
Carefully read the following safety information before proceeding with installation, operation, or mainte-nance of RF Solutions product. Failure to follow these warnings could result in death or serious injury
- This radio system must not be used in areas where there is a risk of explosion.
- Only qualified personnel should be permitted to access the transmitter and operate the equipment.
- Always follow operating information as well as all applicable safety procedures and requirements.
- You must satisfy the age requirements in your country for operating the equipment.
- Store in a safe place.
- Keep a clear view of the work area at all time before using, check it is safe to do so
Before maintenance intervention on any remote controlled equipment
- Do not open the receiver enclosure unless you are qualified.
- Disconnect all electrical power from the equipment.
Battery Precautions
- Risk of explosion if battery is replaced with a battery of an incorrect type.
- Do not short-circuit, disassemble, deform or heat batteries.
- Never attempt to charge a visibly damaged or frozen battery.
- Do not use or charge the battery if it appears to be leaking, deformed or damaged in any way.
- Immediately discontinue use of the battery if, while using, charging, or storing the battery, the bat-tery emits an unusual smell, feels hot, changes color, changes shape, or appears abnormal in any oth-er way.
Electrical Safety
ISOLATE the mains electricity supply before removing the cover and observe any relevant safety information.
- Maintenance to the product that involves removal of the cover should only be carried out by a competent person or qualified electrician.
- Ensure adequate protection on the Load circuit
- Refer to Product Datasheet for MAX operating Load.
- Product must be installed in accordance with the local country electrical regulations.
- A current limiting supply must be used in accordance with the datasheet
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>