RF Solutions MAINSLINK-PRO Two Way Pump Overrun User Guide

June 4, 2024
RF SOLUTIONS

Installation

RF-Solutions-MAINSLINK-PRO-Two-Way-Pump-Overrun-
fig-2

Connect the Supply to both units
Connect the permanent LIVE Feed and NEUTRAL supply.

Connect the Switched Input Lin
Connect the Switching Live input to Lin
When the Switched Live input (LIVE IN) is ‘LIVE’ the LED will illuminate, and the Lout at the other MAINSLINK-PRO will then switch Live out.
Connecting the Switching Load Lout

Multiple System Operation
Each MAINSLINK-PRO system contains a unique identity so multiple systems can operate within the same area without interfering with each other.

Connect your LOAD to Lout
When the Switched Live Output (LOUT) is ‘LIVE’ the Red LIVE OUT LED will illuminate.

Jumper Link Setting

There are three Jumper Links which may be used to configure the following :RF-Solutions-MAINSLINK-PRO-Two-Way-Pump-Overrun-fig-4

WDOG – WATCHDOG
This provides improved reliability and security useful in with electrically noisy Loads.
When the WDOG link is fitted each MAINSLINKPRO automatically sends a background watchdog RF signal and expects to receive a corresponding WDOG signal from its partner.
If the WDOG signal is not received within 90seconds, the output will drop out and comms LED will flash.

MODE

LORA Mode 3 — Faster operation shorter range (Line of sight upto 3Km/500m in buildings)
L ORA Mode 7 — Long range (Line of sight up to 5Km/1Km in buildings)
NOTE! In this mode a transmitted signal can take 2 seconds to trigger the receiver.
MOM/LAT – Must be left OPEN for correct operation.

NOTE: This system does not require pairing, they are supplied ready to operate!

  1. Apply a 230Vac supply to the first MAINSLINK-PRO
  2. Briefly place a magnet across the enclosure (Right side as shown) to activate the internal reed switch.
  3. The GREEN comms LED will flash 3 times to show in Pairing Mode
  4. Apply 230Vac to the second MAINSLINK-PRO
  5. Briefly place a magnet across enclosure (Right Side as shown) to activate the internal reed switch.
  6. The GREEN comms LED will flash 3 times to show in Pairing Mode
  7. The two MAINSLINK-PRO units which will now auto pair together (allow 30 secs -Green Comms LED will stay on.)

Erasing a MAINSLINK-PRO
To erase the system hold a magnet beside the Right Side of the enclosure for 10 seconds as shown.
Repeat this process on both units to erase the system.

Application example: WORCESTER-BOSCH Boiler InstallationRF-Solutions-
MAINSLINK-PRO-Two-Way-Pump-Overrun-fig-1

Operation:

This system provides two functions, Switching of the Pump from the boiler and Switching of the Boiler from the wiring Centre.
When the wiring centre commands the Boiler ON, MAINSLINK-PRO B (Lin) is switched is Live, then MAINSLINK-PRO A Lout will automatically provide a LIVE signal to the boiler on.
When the Boiler outputs the Pump drive ON, MAINSLINK-PRO, (Lin) “A” is switched Live in, then MAINSLINK-PRO B Lout will automatically switch the pump on.

Connections at the Boiler:
The boiler output to the Pump is connected to the MAINSLINK-PRO A, (Live in).
The boiler control switching input is connected to the MAINSLINK-PRO A (Live out).

Connections at the Wiring Centre:
The thermostat switching output to switch the boiler is connected to the MAINSLINK-PRO B (Live in) The Pump is connected to the MAINSLINK-PRO B (Live out).

Warnings:

  • Product is not independently isolated, ISOLATE the mains electricity supply before removing the cover and observe any relevant safety precautions. Maintenance to the product that involves removal of the cover should only be carried out by a competent person or qualified electrician.
  • F2 Fuse rating is 4A (T) 250 H (Ceramic). Replace fuse with same type and rating.
  • Relay is rated at 10A peak, and 5A constant.
  • Product must be connected to a switch fused spur/supply or BS1363 Plug. A single Fuse Spur is recommended to supply the Boiler and MAINSLINK jointly so that they are isolated together.

Hereby, RF Solutions Limited declares that the radio equipment type defined within this document is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.rfsolutions.co.uk

RF Solutions Ltd. Recycling Notice
Meets the following EC Directives:
DO NOT Discard with normal waste, please recycle.
ROHS Directive 2011/65/EU and amendment 2015/863/EU
Specifies certain limits for hazardous substances.

WEEE Directive 2012/19/EU
Waste electrical & electronic equipment. This product must be disposed of through a
licensed WEEE collection point. RF Solutions Ltd., fulfils its WEEE obligations by the membership of an approved compliance scheme. Environment agency
number: WEE/JB0104WV.

Disclaimer:

Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever
for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how t o deploy or use RF Solutions Ltd’s products. Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorized except with express written approval.

No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or re-strict RF Solutions Ltd’s liability for death or personal injury resulting from its negligence.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals