LUPINE 51222 Lamp Head Neo 1000 Lumen User Guide
- June 6, 2024
- LUPINE
Table of Contents
51222 Lamp Head Neo 1000 Lumen
User Guide
Safety Instructions
- Avoid looking directly into the light emitted by the light or shining the light into your own eyes or the eyes of another person.
- If the light accidentally shines into your eyes, close your eyes and move your head out of the light beam.
- Do not use any strongly focusing optical device to look at the light beam.
- In cases where the light is used in a public or commercial setting, users should be provided with training concerning the safety measures for laser light.
- Carry a spare light with you at all times, as the product can potentially fail unexpectedly at any time.
- If you transport the light, always disconnect the lamp head from the battery.
- The Neo housing can heat up to 65°C/149°F. Without any movement, the lamp will dim down automatically to prevent overheating.
- Lamphead and battery are waterproof and impact resistant according to the FL1 Standard, up to 2 meters. However keep in mind, this light is no diving light.
- In the event of any physical or internal battery failure, do not attempt to repair. No user-serviceable parts!
Usage of the Light
Switching on and off:
The light is ready for use when delivered. All you have to do is charge the
battery.
Press the button to switch on the light and cycle through the different light
modes. Keep the button pressed to switch the light off.
Charging the battery:
Plug the included Wiesel charger into an outlet and then connect the battery
to the Wiesel.
LED red on charging
LED green on: the battery is fully charged
Warning!
This charger is to be used to charge rechargeable Li-Ion batteries only.
It is NOT suitable for charging NiMH batteries! Do NOT use non-rechargeable
batteries. – Risk of explosion! This charger may be opened ONLY by the
manufacturer!
Assembly
Helmetlight Neo:
First, attach the thin velcro with the Lupine logo to the helmet mount, then
pull the other end of the velcro through the ventilation openings available on
your helmet and fix it on the other side of the helmet mount.
Direct the light into a straightforward position and tighten the velcro to
avoid slipping of the lighthead during use (see Fig. 1).
With the provided extension, the battery may be carried in your jersey or
backpack. The flexible Velcro strap allows to put the battery directly on the
helmet (see Fig. 2).
Headlight Neo:
Thanks to the battery FastClick-System you can carry all Lupine FastClick
batteries directly on the headband (see Fig. 3).
More Options:
GoPro mount for the helmet and quick-release mount for the handlebar.
Adjust the light levels
The dim levels and a couple of other useful functions can be adjusted. Keep
the button pressed and wait till the main light blinks up once a second.
If you release the button, the particular program as shown below is chosen.
Factory settings
| Dim levels: | Explanation: |
|---|---|
| Dim Levels | 1 |
| 2 | 0.3W + 5W + lOW |
| 3 | 0.3W +1.5W + 5W +10W |
| 4 | Red + 0.3W + 5W + lOW |
for reading maps.
5| Red +0.3W +5W
Additional Functions| 6| Low Start on| The light starts on the lowest beam
7| Low Start off| The light starts on high beam
8| Battery high| Warning & Reservepower activated early
9| Battery low| Warning & Reservepower activated later
10| Alpine SOS| Blinks till the battery is empty or the button pushed
11| SOS| Blinks till the battery is empty or the button pushed
Additional functions
Voltage test:
After connecting the lamp head to the battery, the upper and lower red LEDs
will blink to indicate the battery voltage. The voltage helps to interpret the
remaining capacity.
Upper red LEDs blinks: 1 time each volt
Lower red LEDs blinks: 1 time each 1/10 volt
For example: 7x upper red LEDs + 3x lower red LEDs = 7.3V
Hints:
More than 8V = battery fully charged
7.1 to 7.9V = recharge
Below 7V = not or only partly ready for use
Low battery warning:
Once the remaining capacity dropped by a relevant amount, the lamp heads red
LEDs will turn on. If the battery is empty, the lamp head itself will start to
flash a couple of times. Stop immediately! The light will switch off by
itself.
Reserve power:
After switching the light on again, reserve power is available for a short
while.
Slow down since the light will be switched off automatically.
Important: charge the battery in a short while. Deep discharging will
harm the battery.
An activated reserve power will be shown by the red LEDs flashing.
Smartcore Batteries
Capacity Indicator
Audible:
To check the capacity, simply press the touchpad once. At first an audible
signal will sound, which is especially useful while using the battery mounted
on a helmet or headband, to give a quick reading in 20% steps.
Visible:
The visible indicator uses 5 red LEDs. The LEDs can operate in two different
operating states: blinking and continuous. LED meanings: A blinking LED is
indicating a 10% step and a continuously glowing LED a 20% step.
Example: 3 LEDs steady glow (20 %, 40 %, 60 %) + 1 LED blinking (80 %) = 70%
Capacity Taillight
To run the taillight simply press the touchpad two times and the 5 LEDs will
operate continuously. To switch off the taillight, simply press the pad again.
Moving light:
Press the touchpad three times to activate the moving light. To switch it off
press the button another time.
Miscellaneous
Regulations:
The laws governing the allowable application domain for this lighting system may vary from one country to another. We recommend that you inform yourself about the relevant laws in this domain in your country.
Changes:
Rights for improvements and modifications of our products reserved.
Warranty:
The product’s two-year warranty applies to all components, as well as any
manufacturing defect. The warranty does not include the battery, however. In
addition, any modification or improper use of the product will void the
warranty.
Technical Data:
Power:| Lumens:| Runtime Neo with
2.0Ah battery| with 3.5Ah battery
---|---|---|---
10W| 1000| 1:30h| 2:15h
5W| 600| 3 h| 4:30h
1.5W| 200| 9:30h| 16h
0.3W| 40| 48h| 80h
Red LEDs| –| 48h| 80h
Weight:
Neo Lamphead: 50g
Neo headlamp:
with 2.0Ah battery: 175g
with 3.5Ah battery: 195g
Neo helmet light
with 3.5Ah battery: 175g
Battery:
2.0 Ah / 7.2V Li-Ion
3.5 Ah / 7.2V Li-Ion
Protection Class: IP68
Operating temperature: -25°C to +70°C
Wiesel Charger:
Input Voltage: 100 – 240V~, 50-60Hz
Charging current: 1.9A
More information at www.lupine.de
EC Declaration of Conformity: www.lupine.de/ce/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>