BEGA 24 917 Wall Luminaire Instruction Manual
- July 26, 2024
- BEGA
Table of Contents
**BEGA 24 917 Wall Luminaire Instruction Manual
**
Wall luminaire
Instructions for use
Application
Shielded wall luminiaire with high protection class.
A luminaire made of die cast aluminium and with an impact resistant synthetic
diffuser made of BEGA NeoGlass®.
Product description
Luminaire made of aluminium alloy and stainless steel
BEGA Unidure® coating technology
Colour graphite
Impact resistant synthetic diffuser, BEGA NeoGlass® · diffuse white Silicone
gasket
2 mounting holes ø 5mm
Distance apart 175mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-280 V
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
– Conformity mark
This product contains light sources of energy efficiency class(es) B
Lamp
Module connected wattage : 4.8 W
Luminaire connected wattage : 5.8 W
Rated temperature : ta=25 °C
Service life criteria : 50000 h/L70
24 917 K 3
Module designation : LED-1636/830
Colour temperature : 3000 K
Colour rendering index : CRI > 80
Module luminous flux : 1015 lm
Luminaire luminous flux 370 lm
Luminaire luminous efficiency 63,8 lm/W
- preliminary data
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires
is achieved by using bounce-free switching contacts such as an electronic
relay (solid-state relay), e.g. BEGA 71320.
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo screws.
Remove luminaire top and polycarbonate diffuser with gasket.
Lead the mains supply cable through the cable entry of the luminaire base.
Notice position of use “arrow down” of the luminaire back plate.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
Make sure that gasket is positioned correctly.
Insert polycarbonate diffuser with gasket and luminaire top.
Tighten the screws evenly.
Cleaning · Maintenance
Clean dirt and debris from the luminaire regularly with a clean, soft, lint-
free cloth that is kept damp throughout the cleaning.
If possible, please use water for this, adding a little commercial dishwashing
detergent.
For lacquered surfaces we recommend the use of BEGA Lacquer Care Set 71 179.
Cleaning agents containing solvents and highpressure cleaners are unsuitable
for cleaning and maintenance.
Replacing the LED module
The designation of the LED module is noted on a separate label in the
luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced. Close the luminaire.
IP 65
| Ersatzteile | Spares | Pièces de rechange |
|---|---|---|
| Kunststoffabdeckung | 15 000 859 | Synthetic cover |
| synthétique | 15 000 859 | |
| LED-Netzteil | DEV-0450/350 | LED power supply unit |
| d’alimentation LED | DEV-0450/350 | |
| LED-Modul 3000 K | LED-1636/830 | LED module 3000 K |
| 3000 K | LED-1636/830 | |
| Dichtung | 83 000 495 .A | Gasket |
BEGA Gantenbrink-Leuchten KG · Postfach 3160 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>