SEVERIN HV 7155 2 In 1 Wireless Hand and Stick Vacuum Instruction Manual

SEVERIN HV 7155 2 In 1 Wireless Hand and Stick Vacuum

Important Information

Dear Customer,
Before using the appliance, read the following instructions carefully and keep this manual for future reference. The appliance must only be used by those familiar with the instructions below.

Safety instructions

  Certain groups of persons

• This appliance may only be operated by children over the age of 8 and by persons with reduced physical, sensory or mental capacities or a lack of experience and/or knowledge if they are supervised or have been instructed about the safe use of the appliance and are aware of the dangers associated with its use.
• Children are not allowed to play with the appliance or stand or sit on it.
• Cleaning and user maintenance may not be performed by children without supervision.
• Children under the age of 8 must be kept away from the appliance and the mains adapter.
• The packaging material must not be used for play purposes. There is a risk of suffocation.

Connecting the appliance safely

The appliance is charged with electrical current. Thus, there is a risk of electric shock.
Therefore:

• Check the appliance and mains adapter for possible damage before use. Never operate a defective appliance or an appliance with a defective mains adapter.
• Only connect the mains adapter to sockets which match the specifications on the mains adapter type plate.
• In order to avoid hazards and to comply with safety regulations, any repairs to the appliance and the power supply unit must only be carried out by our customer service. Therefore, in case of repair, contact our customer service by telephone or email (see service addresses in the separate warranty booklet or at www.severin. de).
• Do not immerse the appliance or mains adapter in water or other liquids, or treat with liquids. Keep the appliance and the mains adapter away from rain and wet conditions. Do not operate the appliance and mains adapter outdoors or in rooms with high humidity.
• Do not handle the appliance or mains adapter with wet hands. When unplugging the mains adapter from the socket, always pull directly on the plug.
• Make sure that the cable of the mains adapter is not kinked, pinched or run over and that it does not come in contact with sources of heat, humidity and sharp edges. Make sure that the cable of the mains adapter does not become a trip hazard.
• Before cleaning or servicing the appliance and before changing accessories, switch off the appliance and make sure that the mains adapter is not connected.

Safety when handling rechargeable batteries

• If rechargeable batteries are handled improperly, there is a risk of injury and explosion.
• Never replace the rechargeable battery with other types of batteries. Only use batteries of the same type. Never short-circuit batteries, i.e. do not touch the poles at the same time, especially not with electrically conductive objects. Store rechargeable batteries in such a way that they are not short-circuited by other batteries or metal objects during storage.
• WARNING! Use only the included power supply unit to charge the battery (see Technical Data). Never use another power supply unit to charge the batteries. The power supply unit provided must, in turn, only be used to charge the appliance batteries provided.
• At the end of its life span, remove the rechargeable battery as described. Then take the rechargeable battery to an appropriate collection point nearby without delay, thus ensuring safe and environmentally-appropriate disposal. Never dispose of the rechargeable battery in household waste.
• Before removing the rechargeable battery, make sure that the mains adapter is unplugged from the socket.
• If the appliance is to be stored unused for a long period of time, the battery should be removed and stored separately.
• Never take the rechargeable battery apart, expose it to high temperatures or throw it onto fires.
• In case of improper handling, liquid can escape from the rechargeable battery. Do not use the rechargeable battery if it is damaged or if it is leaking liquid.
• If liquid has escaped, avoid contact with the liquid.
• In case of contact with the liquid, rinse it off immediately with copious amounts of water. In case of after effects (irrespective of type), consult a doctor.

Rotating brush roller

• The appliance has a powered brush roller in the floor and upholstery nozzle. This can cause injuries. Therefore, note the following:
• Before any cleaning or maintenance of the appliance, ensure that the appliance is switched off and not charging.
• WARNING! Ensure that parts of your body can never get under the brush roller.
• Do not vacuum near cables, wires and long fringes. On the one hand, there is a danger that the cable’s insulation will be damaged. On the other hand, these objects can get caught in the brush roller and thereby damage the appliance.

LED lighting

• LEDs are installed in the floor nozzle. These illuminate the work area in front of the floor nozzle.
• Do not look into the LEDs during operation.
• It is not possible to exchange the LEDs.

Intended use

• The appliance must only be used domestically.
• The appliance may only be used for cleaning on level, normally-soiled surfaces, short-pile carpets or upholstery that can withstand exposure to the rotating brush without sustaining damage.
• The appliance may only be used with the corresponding battery (see Technical Data) and accessories.
• Any other use is deemed improper and is forbidden.

In order to prevent injuries, fires and damage, the appliance must not be used to vacuum:

• People, animals or plants. Always keep the device well away from all parts of the body, and from hair and clothing (e.g. shoelaces). Do not use near to your head.
• Glowing, burning or smouldering particles (such as ash, coal, charcoal, cigarettes, matches).
• Explosive or highly flammable substances or toners.
• Water and other liquids, e.g. wet carpet cleaning agents.
• Sharp objects, such as glass splinters, nails or construction waste.
• Fine dust, such as plaster, cement, fine drilling dust, powder.

The following is also forbidden:

• independent alteration or repair of the appliance or its mains adapter.
• Inserting objects into the appliance’s openings. The specially provided accessories are the exception to this rule.
• Use, storage or charging outdoors.
• Cover the ventilation slots on the unit. Keep the ventilation slots free of lint, hair or similar.
• Use of the appliance without filters in place.

CE Marking
This device is compliant with the mandatory EU directives for CE marking.

Device parts / Assembly

Device parts and items included

1. Exhaust filter cover

2. Display

3. Toggle keys:

   • Eco/Power mode
   • Rotation speed brush roller

4. On/Off switch

5. Power supply connection socket

6. Battery

7. Dust container with internal motor pre-filter

8. Telescopic tube

9. Floor tool with brush roller

10. LEDs

11. Turbo upholstery nozzle with brush roller

12. 2-in-1 tool

13. Crevice tool
    
    Not illustrated:

14. Power supply

15. Wall mounting bracket with fastening components

16. Spare motor pre-filter

Installing the wall mount

1. Hold the wall mount to the wall, aligned in a vertical position.

2. Mark the holes with a pencil.

3. Drill the holes.

4. Insert the dowels included in the delivery into the holes.

5. Fasten the wall mount using the screws included in the delivery.

6. Push the charging cable through the cable guide (1) on the right or left side of the wall bracket.

7. Clamp the crevice nozzle and 2in1 tool in the holder (2).
   

8. Push the device onto the wall mounting bracket.

Assembling the appliance

Remove any remaining packaging from the device and assemble the component parts:

1. If necessary, mount the dust container (see also chapter “Cleaning the dust container”), insert the filter and mount the filter cover.
2. Push the suction tube onto the device.
3. Depending on the application, attach the floor nozzle / upholstery nozzle / 2in1 tool / crevice nozzle to the suction tube.

Charging the rechargeable battery

It is best to charge the rechargeable battery before each use, especially after the appliance has not been used for a while. This increases the service life of the rechargeable battery and ensures the longest possible cleaning cycles.

1. Insert the plug of the power supply unit supplied into the connection socket of the appliance.
2. Connect the mains adapter included in the delivery to a socket.
   • The dots in the display on the handle start flashing. The more dots flash, the further the charging process has progressed.
   • As soon as the battery is fully charged, all dots light up for a few minutes and then go out. The charging process takes approx. 5 hours when the battery is empty.
3. Disconnect the mains adapter from the socket.
4. Pull the plug of the power supply unit out of the connection socket of the appliance

The operating time with a fully charged rechargeable battery is approximately 18 minutes (in Power mode) or 40
minutes (in Eco mode).
TIP: If the appliance is used infrequently, the power supply should not remain permanently connected.

Operating the appliance

Selecting floor nozzle, turbo upholstery nozzle, 2in1 tool or crevice nozzle

The brush attachment can be pushed back, e.g. to suck up crumbs. To do this, press the locking button on the brush and push it forwards or backwards.
Crevice nozzle| : for vacuuming hard-to-reach corners

• Select the desired attachment and place it on the mounted appliance.
• Adjust the telescopic tube to the desired length.
• All attachments can also be used without the suction tube, e.g. to vacuum furniture. Make sure that the substrate can withstand the stress of the brush roller without damage.

Vacuuming in Eco mode
In power mode, the hand vacuum has a higher output. The brush roller rotates.

1. Attach the floor nozzle to the suction tube.
2. Press the switch on the handle of the appliance to switch on the appliance. Eco mode is activated.
3. Vacuum the floor.
4. Press the switch again to switch off the appliance.
5. Empty and clean the dust container (see chapter “Maintaining the appliance”).

Vacuuming in Power mode
In Power mode the hand-held vacuum cleaner operates with higher power and the brush roller rotates

1. Attach the floor nozzle to the suction tube.
2. Press the switch on the handle of the appliance to switch on the appliance. Press the rear button on the top of the handle once. Power mode is activated, MAX lights up in the display.
3. Vacuum the floor.
4. Press the switch again to switch off the appliance.

Switch brush roller for carpet or hard floor
If the front button on the top of the handle is pressed, the rotation speed for the brush roller can be changed. We recommend fast turning ( ) for carpets and upholstery and slow turning ( ) for hard floors.

Storing the appliance

Convenient stowage function
The appliance can be stored either on the wall bracket or upright in a cupboard or protected corner. To do this, the telescopic tube must be pushed in completely. Never leave the appliance with the handpiece in a free-standing position in a room or similar place to prevent it from falling over. An appliance falling over may cause injury or damage to the appliance/battery

Maintaining the appliance

Emptying the dust container
The dust container can only hold a limited quantity of dirt.
It is therefore best to empty the dust container after every cleaning procedure and if the suction power noticeably drops.

1. Make sure that the appliance is switched off and is not on charge.
2. Take the suction tube off.
3. Press the button button on the side of the dust container. The flap opens and the contents of the dust container can be emptied.
4. Close the flap.

Cleaning the dust container and motor pre-filter

1. Make sure that the appliance is switched off and is not on charge.

2. Empty the dust container (see chapter ‘Emptying the dust container’).

3. Turn the handpiece over so that the dust container is facing upwards.

4. Unlock and remove the dust container lid by turning it anticlockwise.

5. Unlock the dust container insert anticlockwise and remove it.

6. Remove the motor pre-filter from the dust container.

7. Pull the foam cover off the filter and tap it out.

8. Thoroughly tap out and brush off the filter. In doing so, turn the filter material inside out.

9. Brush the dust container insert.
   Note: All parts may be cleaned under running water. Make sure that all parts are completely dry before using the appliance again. The drying time of the filter is about 24 hours.

10. After complete drying of the individual parts, push the filter cloth into the filter.

11. Pull the foam cover over the filter and place the filter in the dust container.

12. Put the dust container insert over it and lock it in place by turning it .

13. Place the dust container lid on the hand part and lock it by turning it clockwise until and are facing each other

Cleaning the blow-out filter

1. Ensure that the appliance is switched off and not charging.
2. Unlock the cover of the blow-out filter anticlockwise  and remove it.
3. Remove the blow-out filter and clean it under running water. Allow to dry for 24 hrs.
4. Reinsert the filter after it is completely dry.
5. Put on the cover of the outlet filter and lock it by turning until and are facing each other.

Cleaning the brush roller in the floor tool and the upholstery tool
Dirt may prevent the brush rollers from rotating freely. Clean the brush rollers regularly

1. Make sure that the appliance is switched off and is not on charge.

2. Remove the tool from the suction tube.

3. Floor nozzle:
   Turn the nozzle upside down. Press in and release the locking device of the brush roller on the left underside of the nozzle. Carefully remove the brush roller.
   Upholstery nozzle:
   Release the lock on the side of the upholstery nozzle  . Carefully remove the brush roller to the side.

4. Remove any hair and dirt from the brush, using a pair of tweezers or scissors carefully, if necessary.

5. Fit the brush back onto the tool.
   Floor nozzle:
   Fix the brush roller on the right and press it down on the left side. Reinsert the lock into the nozzle and press it firmly.
   Upholstery nozzle:
   Insert the brush roller from the side into the upholstery nozzle and lock it .

Troubleshooting

Troubleshooting by yourself
To avoid problems, it is important to empty the dust container in good time and to take this opportunity to check and clean the motor pre-filter.

discharged. Switch off the appliance and charge the rechargeable battery, ► chapter “Charging the rechargeable battery”.
The appliance cannot be charged(LEDs do not flash).| The mains adapter is not plugged in correctly. Check whether the mains adapter’s connector and the mains adapter are connected firmly to their sockets, ► chapter “Charging the rechargeable battery”.
The rechargeable battery has not been inserted correctly. Disconnect the mains adapter. Check that the rechargeable battery is seated correctly inthe appliance. Connect the mains adapter again.
The appliance hardly picks up any dust.| The dust container needs to be emptied or the motor protection filter and the dust container need to be cleaned, ► chapter “Maintaining the appliance”.
Operating durations becoming progressively shorter.| The brush roller is soiled and needs to be cleaned, ► chapter “Cleaning the brush roller”.
The brush roller rotates slowly or irregularly.| The brush roller is soiled and needs to be cleaned, ► chapter “Cleaning the brush roller”.
---|---
The brush roller and LEDs switch off automatically.| This is a safety function that prevents the nozzle becoming defective if the brush roller gets jammed.
The brush roller is either dirty and needs to be cleaned, ► chapter “Cleaning the brush roller” or something has got jammed in the brush roller, e.g. when vacuuming a high pile carpet. To override the power-off, switch off the vacuum cleaner, take the nozzle off of the suction tube or the hand-held vacuum cleaner and remove any objects that may be blocking the brush roller.
The brush roller and LEDs will function again as normal when the vacuum cleaner is next switched on.

Service hotline
If you cannot solve the problem using the table, call our Service Hotline (see contact details in a separate warranty booklet).

Disposal and warranty

Removing and replacing the battery
Press the locking buttons on the battery and remove the battery.
Inserting the battery
Place the battery on the guide rails on the appliance and press until it clicks into place.

Disposing of the appliance and rechargeable battery separately
 Devices and batteries marked with this symbol must be disposed of separately from household waste! Devices and batteries contain valuable raw materials that can be recycled. Proper disposal of these items protects the environment and public health. Return the device and the battery separately to the appropriate collection points for disposal.

Customer Support

D-59846 Sundern
Tel +49 2933 982-0
Fax +49 2933 982-1333
information @severin.de

www.severin.com

References

• SEVERIN Onlineshop
• SEVERIN Onlineshop
• severing.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>