OZ LIFTING PRODUCTS OBH1000NG Builder’s Hoist Wireless Instruction Manual

OZ LIFTING PRODUCTS OBH1000NG Builder’s Hoist Wireless Instruction Manual

MODEL# OBHW600

POWERFUL LIGHTWEIGHT VERSATILE REMOTE CONTROLLED

CAUTION
READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF YOUR WIRELESS ELECTRIC HOIST

Please read the Owner’s Manual carefully before operating this product.
Keep this manual available at all times.

Introduction:

The OZ Builder’s Hoist Wireless is designed for use on commercial buildings sites and in various construction workplaces, warehouses, storage facilities and factories.

Ensure the Hoist is mounted on a straight bar which only allows the hoist to swing backward and forward and not left to right or swing 360 degrees. Failure to do this could result in uneven winding of rope onto the drum, rope jamming, and rope damage.

Specifications:

MODEL: OBHW600

• Lifting Capacity (Full Drum): 600 lbs
• Motor Voltage: 115/1/60
• Speed: 52 fpm
• Motor: 2 HP
• Motor KW: 1500W / 12.5A
• Lifting Height: 90 ft
• Wire Rope: 3/16 in
• Winch Weight: 43 lbs
• Gross Weight: 49 lbs
• Power cord length: 15 ft

Product Features

• Lightweight and compact design for convenient mounting
• Automatic shut-off when rope reaches limit arm
• Sensor arm for motor shut-off to prevent reverse winding
• Standard 115V power source-compatible
• Wireless remote control for ease of use
• 360-degree hook with safety latch•Emergency UP / DOWN control switch
• Built-in safety features and easy control of lifting for a wide range of applications

Safety Precautions:

Environmental Precautions
The following conditions may result in hoist failure or damage:

NOTE: Never exceed the duty cycle of the hoist. The duty cycle for OZ Builder’s Hoist Wireless is 15 continuous minutes or 75 starts per hour. Please follow these ratings.

The life of the hoist depends on attention to the load and to working frequency. Use the hoist only within its duty cycle.

With any electric motor, it is important to let the motor cool after reaching the duty cycle.

Handling Precautions
Failure to follow these handling precautions may result in personal injury or equipment damage.

Assembly:

****Very important when connecting the wire rope to the bottom hook the cable must run on the outside of the lower limit bar. If ran on the inside of the bar damage will happen to the wire rope and the hoist.

Mounting
Ensure the hoist is mounted on a straight bar that allows only for front-to- back swinging, not left-to-right or rotational swinging. Failure to do so could result in uneven winding of rope onto the drum, rope jamming and rope damage. When hanging the hoist, ensure it is free from other obstructions. Always keep the hoist as level as possible to prevent uneven winding.

NOTE: Always lock the hanger before every lift.

Connecting the Cords

Power cord:

1. Align the power cord with the matching socket on the power receptacle of the hoist. Push in tightly.
2. Secure the power cord with the strain relief clip. This clip is attached to the power cord and secures to a ring on the hoist to reduce cable strain. Do not allow the power cord to come into contact with the wire rope or drum.
3. The power cord is designed for distances of 65 ft or less. For additional length, use a power cable of 12 (AWG) to prevent a drop in voltage.

Power cord length selections
Section 14 (AWG) – Cord Length 65 ft.
Section 12 (AWG) – Cord Length 114 ft.

Grounding:
To prevent the risk of electric shock, the power plug must be plugged into a matching outlet in good condition.

Working Methods

Preparation

• Always maintain a line of site with the hoist while operating.•Confirm a safe working environment prior to operation.
• Ensure a minimum of five (5) wraps of wire rope is wound around the drum.
• Discard wire rope that shows signs of excessive wear or broken wires. Look for corrosion or other defects.
• Connect the main power source. There will be a loss of power if input voltage falls out of rated voltage by +10%.
• Do not lift loads exceeding the rated load.

Remote Control Up-and-Down Switching
Push the green (Start) button to turn on the remote control.
Press the up button and the drum will take in cable, lifting the load. Press the down button and the drum will let out cable, lowering the load. To stop the drum, release the button.

Emergency Switch
If your wireless remote control is malfunctioning or lost in the loading situation. To avoid the danger, please operate the emergency button on the winch body to move the loading things to safe place.

Oil Lubrication

Winches are pre-oiled at the factory and do not require initial lubrication. Relubrication interval depends upon service. Recommended oil replenishment quantity & intervals are as follows.

• Model# OBHW600
• Oil Grade: SAE 630
• Oil Amount: 8.45 oz.
• Intervals: As needed

Carbon Brush Replacement

WARNING

Clean the accumulated powder off carbon brushes periodically.

• It is essential to check the carbon brushes periodically.
• If the length is less than .30 in. replace carbon brushes immediately.
• While replacing, smoothly insert carbon brush into carbon holder.
• Before tightening the carbon brush holder, make sure to position the O ring.

ONE YEAR WARRANTY

OZ Lifting Products LLC® guarantees this product to be free of defects in materials and workmanship for one year from the date of shipment.

This warranty does not apply to products that show signs of misuse, overloading, alteration, improper maintenance or negligence. The normal wear and tear of moving parts is excluded from the warranty. Moving parts are defined as brake discs, wire rope and other wear components that are subject to use conditions. This warranty does not cover any costs related to removal of this product, lost time, or any other incidental or consequential damages/costs resulting from the claimed defects.

If this product fails during the first year of operating due to defective materials or workmanship, it will be repaired or replaced at the discretion of OZ Lifting Products LLC®. Any product subject to a warranty claim must be returned, prepaid, to an authorized OZ Lifting Products LLC® warranty depot along with proof of purchase. Upon repair, the product will be returned to the customer free of charge. If no defect is found,the customer will be responsible for return shipping costs. The product’s warranty will be effective for the remainder of the original warranty period (one year from shipment date).

OZ Lifting Products LLC® will not be held liable for the following arising from the use of this product: injuries to persons or property, death, incidental, consequential, or contingent damages, whether negligent or deliberate. It is the sole responsibility of the owner to install and operate the product properly and safely.

This is OZ Lifting Products LLC®‘s only written warranty. This warranty is in lieu of all other warranties implied by law such as merchantability and fitness. The sale of products from OZ Lifting Products LLC® under any other warranty or guarantee, expressed or implied, is not authorized.

NOTE: OZ Lifting Products LLC® has the right to alter the design of or discontinue the production of any product without prior notice.

OBHW600 Parts Breakdown

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>