BEGA 24918K3 Ceiling Light and Wall Light Instruction Manual
- July 26, 2024
- BEGA
Table of Contents
BEGA 24918K3 Ceiling Light and Wall Light
Specifications
- Model: Wandleuchte Wall luminaire Applique
- Model Number: 24 918
- Dimensions: 25 x 18 x 12 cm
- Weight: 300g
- Power Consumption: 11.6W (Lamp Module), 13.5W (Luminaire)
- Colour Temperature: 3000 K
- Colour Rendering Index (CRI): >80
- Luminous Flux: 2440 lm (Module), 850 lm (Luminaire)
- Luminous Efficiency: 63 lm/W
Product Usage Instructions
Safety
The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform installation and commissioning. The manufacturer is not liable for damage due to improper use or installation.
Overvoltage Protection
The luminaire’s electronic components have overvoltage protection according to DIN EN 61547. Additional protection against transients is recommended. Visit our website for separate overvoltage protection components.
Installation
- Undo screws and remove luminaire top with polycarbonate diffuser.
- Lead mains supply cable through the cable entry of the luminaire base.
- Ensure the luminaire back plate’s use arrow is facing down.
- Fix the luminaire base onto the mounting surface using suitable fixing material.
- Connect the earth conductor and electrical connections.
- Place the enclosed desiccant pouch in the luminaire to protect electronic components.
- Insert polycarbonate diffuser with gasket and tighten screws evenly.
Application
Shielded wall luminiaire with high protection class.
A luminaire made of die cast aluminium and with an impact resistant synthetic
diffuser made of BEGA NeoGlass®.
Dimension
Product Description
- Luminaire made of aluminium alloy and stainless steel
- BEGA Unidure® coating technology
- Colour graphite
- Impact-resistant synthetic diffuser, BEGA NeoGlass® · diffuse white
- Silicone gasket
- 2 mounting holes ø 5.2 mm
- Distance apart 210 mm
- 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
- Connection terminal 2.5@
- Earth conductor connection
- Complies with flicker requirements in accordance with IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1
- LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 170-276 V
- BEGA Thermal Switch®
- Temporary thermal shutdown to protect temperature-sensitive components
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
- Conformity mark
This product contains light sources of energy efficiency class(es) B
Lamp
- Module connected wattage 11.6 W
- Luminaire connected wattage 13.5 W
- Rated temperature ta = 25 °C
- Service life criteria 50 000 h / L70
24 918 K3
- Module designation LED-1639/830
- Colour temperature 3000 K
- Colour rendering index CRI > 80
- Module luminous flux 2440 lm
- Luminaire luminous flux * 850 lm
- Luminaire luminous efficiency * 63 lm / W
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires
is achieved by using bounce-free switching contacts such as an electronic
relay (solid-state relay), e.g. BEGA 71 320.
Installation
- LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
- Undo screws.
- Remove luminaire top and polycarbonate diffuser with gasket.
- Lead the mains supply cable through the cable entry of the luminaire base.
- Notice position of use “arrow down” of the luminaire back plate.
- Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
- Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection.
- In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
- Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
- Make sure that gasket is positioned correctly. Insert polycarbonate diffuser with gasket and luminaire top.
- Tighten the screws evenly.
Cleaning · Maintenance
- Clean dirt and debris from the luminaire regularly with a clean, soft, lint-free cloth that is kept damp throughout the cleaning.
- If possible, please use water for this, adding a little commercial dishwashing detergent.
- For lacquered surfaces we recommend the use of BEGA Lacquer Care Set 71 179.
- Cleaning agents containing solvents and high-pressure cleaners are unsuitable for cleaning and maintenance.
Replacing the LED module
- The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
- The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
- Inspect and, if necessary, replace the luminaire gaskets.
- Defective glass must be replaced.
- Close the luminaire.
Spares
Synthetic cover 15 000 860
LED power supply unit DEV-0341/350
LED module 3000 K LED-1639/830
Gasket 83 000 514
FAQ
Q: Can I directly touch the LED during installation?
A: Avoid touching the light output opening of the LED directly during installation or relamping to maintain product quality.
Q: Where should I place the desiccant pouch?
A: Place the desiccant pouch in the position marked by the red information label before closing the luminaire to protect electronic components.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>