BEGA 24911K3 Ceiling and Wall Luminaire Instruction Manual

: July 26, 2024
: BEGA

Table of Contents

BEGA 24911K3 Ceiling and Wall Luminaire
Product Usage Instructions
FAQ
Dimension
Instructions for use
Product Description
Safety
Overvoltage protection
Installation
Cleaning · Maintenance
Replacing the LED module
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24911K3 Ceiling and Wall Luminaire

Specifications:

Model: 24 911 K3
Module designation: LED-1632/830
Colour temperature: 3000 K
Colour rendering index (CRI): > 80
Module luminous flux: 1220 lm
Luminaire luminous flux: 870 lm
Luminaire luminous efficiency: 127.9 lm/W
Lamp Module connected wattage: 5.8 W
Luminaire connected wattage: 6.8 W
Rated temperature: 50°C
Service life criteria: 25,000 hours

Product Usage Instructions

Safety:

The installation and operation of this luminaire must adhere to national safety regulations. Installation and commissioning should\ only be performed by a qualified electrician. The manufacturer is not liable for damages resulting from improper use or installation.

Overvoltage Protection:

The luminaire’s electronic components are protected against overvoltage per DIN EN 61547 standards. For additional protection, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.

Installation:

Undo screws and remove luminaire top with the polycarbonate diffuser and gasket.
Lead the mains supply cable through the cable entry of the luminaire base.
For wall installation, ensure the position of the application arrow is downwards.
Secure the luminaire base onto the mounting surface using appropriate fixing material and gasket rings provided.
Connect the earth conductor and electrical connections.
To maximize service life, place the enclosed desiccant pouch in the designated area before closing the luminaire.
Ensure correct positioning of gasket, then insert the polycarbonate diffuser with gasket and luminaire top before tightening screws evenly.

FAQ

Q: Can I touch the light output opening of the LED during installation?
- A: It is recommended to avoid touching the light output opening directly to prevent damage to the high-quality electronic components.
Q: What is the recommended wattage for the lamp module and luminaire?
- A: The lamp module connected wattage is 5.8 W, and the luminaire connected wattage is 6.8 W.

Dimension

Instructions for use

Application

Unshielded luminaire with high protection class for installation under ceilings and on walls. A luminaire made of die cast aluminium and impact resistant synthetic diffuser made of BEGA NeoGlass®. For interior and exterior lighting applications.

Product Description

Luminaire made of aluminium alloy and stainless steel
BEGA Unidure® coating technology
Colour graphite
Impact resistant synthetic diffuser,
BEGA NeoGlass® · diffuse white
Silicone gasket 2 mounting holes ø 5 mm
Distance apart 140 mm
2 cable entries for through-wiring of mains
supply cable ø 7-10.5 mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 0/50-60 Hz
DC 176-280 V
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
CE Conformity mark
This product contains light sources of energy efficiency class(es) B

Lamp

Module connected wattage 5.8 W
Luminaire connected wattage 6.8 W
Rated temperature ta = 25 °C
Service life criteria 50 000 h / L70

24 911 K3

Module designation LED-1632/830
Colour temperature 3000 K
Colour rendering index CRI > 80
Module luminous flux 1220 lm
Luminaire luminous flux * 870 lm
Luminaire luminous efficiency * 127,9 lm / W

preliminary data

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com. The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Undo screws. Remove luminaire top and polycarbonate diffuser with gasket. Lead the mains supply cable through the cable entry of the luminaire base. For wall installation note the position of application “arrow down”. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Be sure to use the gasket rings supplied. Make the earth conductor connection and the electrical connection. In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire. Make sure that gasket is positioned correctly. Insert polycarbonate diffuser with gasket and luminaire top. Tighten the screws evenly.

Cleaning · Maintenance

Clean dirt and debris from the luminaire regularly with a clean, soft, lint- free cloth that is kept damp throughout the cleaning. If possible, please use water for this, adding a little commercial dishwashing detergent. For lacquered surfaces we recommend the use of BEGA Lacquer Care Set 71 179. Cleaning agents containing solvents and high-pressure cleaners are unsuitable for cleaning and maintenance

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. The defective glass must be replaced. Close the luminaire.

Spares