WORKPRO W125041A Cordless Hot Glue Gun Operating Instructions

WORKPRO W125041A Cordless Hot Glue Gun

Danger! – Read the operating instructions to reduce the risk of injury

Caution! Wear safety goggles. Sparks generated during working or splinters, chips, and dust emitted by the device can cause loss of sight.

For use in dry rooms only.

Safety class II

Danger!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents that arise due to a failure to follow these instructions and the safety instructions.

1. This equipment can be used by children of 8 years and older and by people with limited physical, sensory, or mental capacities or those with no experience and knowledge if they are supervised or have received instruction in how to use the equipment safely and understand the dangers which result from such use. Children are not allowed to play with the equipment. Unless supervised, children are not allowed to clean the equipment or carry out user-level maintenance work.
2. The battery must be removed before the equipment is scrapped.
3. The equipment must be disconnected from the power supply before removing the battery.
4. The battery must be disposed of properly.

SAFETY REGULATIONS

• The corresponding safety information can be found in the enclosed booklet.
• Danger! Read all safety regulations and instructions.
• Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury.
• Keep all safety regulations and instructions in a safe place for future use.

LAYOUT AND ITEMS SUPPLIED

Layout (Fig. 1)

1. ON/OFF switch
2. LED indicators
   • 2a Battery capacity/charge level indicator 2b Temperature indicator
3. Nozzle
4. Trigger lever
5. Fold-up stable stand
6. Micro USB charging port
7. Charging cable
8. Charger
9. Glue stick

Items supplied

CARTON CONTENTS

• Cordless Hot Glue Gun
• Charger
• 20pc 7x100mm(5/16x4inch) glue sticks
• Original safety and operating instructions

1. Carefully check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, please contact us at the first time.

NOTE: Do not discard the shipping carton and packaging material until you are ready to use your new cordless hot glue gun. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. These items can be swallowed and pose a suffocation risk!

PROPER USE

• You can use the cordless hot glue gun to glue the following materials: Wood, plastics, textiles, cardboard, ceramics, leather, etc.
• The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
• Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

TECHNICAL DATA

• Power supply: 3.6 V DC
• Heat-up time: approx. 100 seconds
• Melting temperature: 150 °C (302°F)
• Glue stick diameter: 7 mm(5/16″)
• Glue stick length: 100 mm((4″)
• Battery capacity: 2.6 Ah
• Battery type: Lithium-ion
• Weight: 0.2 kg
• Charger for the product
  • Battery charge voltage: 5 V DC
  • Battery charge current: 1 A
• Charging unit
  • supply voltage: 100-240V~ 50/60 Hz
  • Charging time: 2.5-3.5 hours

Caution!

Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be ruled out. The following hazards may arise in connection with the equipment’s construction and layout:

• Lung damage if no suitable protective dust mask is used.

BEFORE STARTING THE

EQUIPMENT Hazard! Charge the equipment only with the charger supplied. Only place the equipment on non-flammable surfaces.

Charging the battery (Fig. 2)

• The battery is protected from exhaustive discharge. An integrated protective circuit automatically switches off the equipment when the battery is flat.
• Note! Do not actuate the ON/OFF switch anymore if the protective circuit has tripped. This may damage the battery. Check that your mains voltage is the same as that marked on the rating plate. Plug the battery charger(8) into the plug socket and connect the charging cable (7) to the Micro
• USB charging port (6). The charging process starts as soon as the charging cable is connected to the charging adapter.
• The LED (2a) will light up red to indicate that the battery pack is being charged. When charging is finished, the LED (2a) changes to green.
• If no LEDs come on during charging, this means that the battery pack is defective. A defective battery is not allowed to be used any more.

Important! The handle may become a little warm during the charging process. This is normal. If the battery fails to charge, please check

• whether there is voltage at the socket outlet
• whether there is good contact at the charging contacts of the charging unit.

If the battery still fails to charge, please contact our online customer service

Inserting the glue stick (Fig. 3)

• Push the glue stick (9) into the opening (B) as far as the stop.

OPERATION

Operation

• Check that a glue stick is fitted (see point 5.2)
• Long press the ON/OFF switch (1) for approx. 2 seconds.
• The LED (2b) will light up red to indicate that the equipment is heating up
• This takes approx. 100 seconds, after which the LED (2b) changes to green
• The equipment is now ready for operation.
• To switch the equipment off again, press the ON/OFF briefly just the once

Warning! Never set the equipment down once you have started using it.

If or when your gluing work is interrupted or finished,always be sure to stand the equipment on its fold up stable stand asshown in Fig.1. Switch the equipment off and allow it to cool down completely before you pack it away.

Working with the cordless hot glue gun

• You can now apply the glue by pressing the trigger lever (4) after the heating up time
• Press both surfaces together immediately and apply pressure to them
• It takes about 30 seconds for the glue to set.

The equipment switches off automatically after approx. 5 minutes of non-use.

Important! Glue stains on textiles cannot be removed.

LED indicator (Fig. 2/Item 2)

• The indicator (2) displays the charging status during charging (see point 5.1), the heating time and when the equipment isready for operation (see point 6.1). If the red LED (2a) turns to be red during operation,the battery is empty. Recharge the battery.

CLEANING AND MAINTENANCE

Warning! Allow the equipment to cool down before you start to clean it.

Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of theequipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

Maintenance

• There are no parts inside the equipment which require additional maintenance.

STORAGE

• Store the equipment and accessories in a dark and dry place at above freezing temperature.
• The ideal storage temperature is between 5°C(41°F) and 30°C(86°F).
• Store the electric tool in its original packaging.

DISPOSAL AND RECYCLING

• The equipment is supplied in packaging to prevent it from being damaged in transit.
• The raw materials in this packaging can be reused or recycled.
• The equipment and its accessories are made of various types of material, such as metal and plastic.
• Never place defective equipment in your household refuse.
• The equipment should be taken to a suitable collection center for proper disposal.
• If you do not know the wherea bout of such a collection point, you should ask in your local council offices.

This product has been marked with a symbol relating to removing electric and electronic waste. This means that this product shall not be discarded with household waste but that it shall be returned to a collection system. It will then be recycled or dismantled in order to reduce the impact on the environment. Electric and electronic equipment can be hazardous for the environment and for human health since they contain hazardous substances.

DISPOSAL OF AN EXHAUSTED BATTERY PACK

To preserve natural resources, please recycle or dispose of the battery pack properly. This battery pack contains Li-ion batteries. Consult your local waste authority for information regarding available recycling and/or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy-duty adhesive tape to prevent short circuits and energy discharge. Do not attempt to open or remove any of the components.

Hangzhou Great Star Industrial Co., Ltd. No.35 Jiuhuan Road, Jiubao Town, www.greastartools.com

FREQUENTLY ASKED QUESTIONS

What is the weight of the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A Cordless Hot Glue Gun weighs 6.91 ounces.

What type of power source does the WORKPRO W125041A use?

The WORKPRO W125041A is powered by a lithium-ion battery, making it cordless and portable.

What is the voltage of the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A operates at 3.6 volts (DC).

What are the dimensions of the WORKPRO W125041A Cordless Hot Glue Gun?

The dimensions of the WORKPRO W125041A are 7.48 x 4.72 x 2.36 inches.

What materials are used in the construction of the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A is made from steel and ABS plastic.

How many batteries are required for the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A requires one lithium-ion battery.

What is the price of the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A Cordless Hot Glue Gun is priced at $23.99.

Who is the manufacturer of the WORKPRO W125041A?

The WORKPRO W125041A is manufactured by HANZGHOU GREATSTAR INDUSTRIAL CO., LTD.

What is the UPC code for the WORKPRO W125041A Cordless Hot Glue Gun?

The UPC code for the WORKPRO W125041A is 820909764809.

What type of battery is used in the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A uses a lithium-ion battery.

How does the WORKPRO W125041A Cordless Hot Glue Gun charge?

The battery of the WORKPRO W125041A is charged using a provided charging base or adapter.

What glue stick size is compatible with the WORKPRO W125041A Cordless Hot Glue Gun?

The WORKPRO W125041A is compatible with standard-sized glue sticks, usually 7mm or 10mm in diameter.

Why isn't the WORKPRO W125041A Cordless Hot Glue Gun heating up?

Ensure the battery is fully charged. If the gun still doesn't heat up, check for any visible damage to the heating element or internal wiring.

What should I do if the glue is not dispensing from my WORKPRO W125041A Cordless Hot Glue Gun?

Check that a glue stick is properly inserted and that the gun has had sufficient time to heat up (usually 3-5 minutes). If the problem persists, the nozzle might be clogged; let the gun cool and carefully clean the nozzle.

Why is the glue coming out too slowly from the WORKPRO W125041A Cordless Hot Glue Gun?

Ensure the glue gun has reached its optimal temperature. If it's still slow, try using a different brand of glue sticks as some may have different melting points.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK: WORKPRO W125041A Cordless Hot Glue Gun Operating Instructions

REFERENCE:WORKPRO W125041A Cordless Hot Glue Gun Operating Instructions- Device.Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>