WORKPRO Multi Pupose Workbench with Work Light User Manual

Multi Pupose Workbench with Work Light

The following tool is required for installation:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

1. Attach 1 Side Beam (#4) to the bottom 2 holes of 1 Front Beam (#1) and 1 Back Beam (#2). Repeat with other Side Beam, Front Beam, and Back Beam. (See Figure A)
NOTE: Back posts are taller than Front posts.
2. Attach the Protective Caps (#3) at the bottom of all 4 Beams. (See Figure A)

4. Working from the front side of the workbench, attach the Side Beam (#4) and the Side Beam with Power Strip Opening (#4A) to the top 2 holes on the Front Posts (#1) and the middle 2 holes on the Back Posts (#2). (See Figure C)
NOTE: The side Beam with Power Strip Opening can be attached to either right or left side.
5. Attach Power Strip (#22) to the Side Beam with Power Strip Opening (#4A) using U Brackets (F) and Screws (E) from package E-F. (See Figure C)

3. Attach the Bottom Beams (#5) to join both the Front Beams (#1) and both Back Beams (#2), connecting together the bottom of the workbench. (See Figure B)

6. Attach the Top Beams (#6) to the top 2 holes on both Front Posts (#1) and the middle 2 holes on both Back Posts (#2). (See Figure D)
NOTE: Make sure the Front Top Beam (#6) carries the Warning Label and is rightside-up.

7. To begin assembling the Drawer Housing, attach the Front Drawer Bracket (#7F) to the Front Top Beam (#6). Next attach the Back Drawer Bracket (#7B) to the Back Top Beam (#6). (See Figure E)

11. Attach the Front Drawer Panel (#11) to the Right (#10R) and Left (#10L) Drawer Panels. Slip the Drawer Bottom onto the Drawer Panel lips, and attach the Back Drawer Panel (#12) to secure Drawer Bottom into place. Repeat for Second Drawer. Attach Drawer Handles to Front Drawer Pannel (#11). (See Figure G)
12. Slide the Drawers into the Drawer Bracket Runners and push firmly until the drawers go all the way to the back of the track.
NOTE: Drawers have light locking device, push firmly to make drawers flush

Replace light fixture only with same light fixture size and rating.

12. The peg board is designed for hooks that diameter of wire is less than 3.7mm(9/64″).

17. Attach the Pegboard (#18) to the Back Upper Posts (#15) and Middle Drawer Mount using Bolts, and Nuts from package C. (See Figure I)
NOTE: You will have to temporarily remove the screws, one side at a time, to be able to secure the Pegboard to the bottom corners of the Back Upper Posts (from Step 13)
NOTE: Now you will want to go through and tighten all Screws and Bolts securely, it is more difficult to do after surfaces have been installed.

19. Attach the Top Shelf (#21) to the Shelf Beams (#17L + #17R) using the Bolts, Nuts from package D. (See Figure K)

20. Attach the Light Fixture (#23) to the underside of the Top Shelf (#21) using the Screw and clip (H) from package G. (See Figure L)
a. Insert a screw at the center of each Light Fixture Clip.
b. Position the screws at the center of the designated holes on the underside of the Top Shelf, and screw them into the Shelf until the Clips are secure.
c. Push the Light Fixture all the way into the clips to securely attach to the Top Shelf.
H

8. Attach the Middle Drawer Mount (#8) to the Front Drawer Bracket (#7F) and the Back Drawer Bracket (#7B).
NOTE: The side with the open end of the silver runner track should be facing forward, and the end that is closed should be facing the back of the workbench.

(#15)
13. Attach the left and right Back Upper Posts (#15) to the left and right Back Posts (#2) on the top most 2 holes. NOTE: You will have to temporarily remove these screws to attach the pegboard in the future, so do not overtighten.
14. Attach the Back Shelf Beam (#16B) to the top of the Back Upper Posts 1(#15). NOTE: Install Shelf Beams with the lip facing upward. This will be used to attach theTop Shelf in future steps.
15. Attach the Left Shelf Beam (#17L) and the Right Shelf Beam (#17R) to the Back Shelf Beam (#16B) to begin forming the top shelf. NOTE: Install Shelf Beams with the lip facing upward. This will be used to attach theTop Shelf in future steps.

9. Attach the Left Drawer Mount (#9L) to the left Front and Back Beams on the bottom most holes. Then Attach the Right Drawer Mount (#9R) to the right Front and Back Beams on the bottom most holes. (See Figure F)
NOTE: Again, the runner tracks with the open end should be facing forward, and the end that is closed should be facing the back of the workbench.

16. Attach the Front Shelf Beam (#16F) to the Left and Right Shelf Beams (#17L + #17R). (See Figure H)
NOTE: Install Shelf Beams with the lip facing upward. This will be used to attach theTop Shelf in future steps.

18. Attach the Bench Top (#19) to the Side Beams (#4 + #4A). Then attach the Bottom Shelf (#20) to lower Side Beams (#4). Use the Bolts, Nuts from package D. (See Figure J)

21. Route the Light Fixture cord through one of the holes at the top side of the Pegboard and plug in the Light Fixture power cord to the Power Strip on the side of the Workbench. Secure the power cord to the Back Post with the zipties provided.
NOTE: Go through one more time and ensure all Screws and Bolts are securely tightened on the Workbench.

Replace light fixture
1. Pull the light fixture from light fixture clips. 2. Push the Light Fixture all the way into the clips to securely attach to the Top Shelf.

H Clip

2

A.

x 8

B.

x 78

C.

x 12

D.

x 18

E.

x 4

G.

x 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>