BEGA 24 894 Ceiling and Wall Luminaire Instruction Manual

: July 17, 2024
: BEGA

Table of Contents

BEGA 24 894 Ceiling and Wall Luminaire
Specifications
Product Usage Instructions
FAQ
Dimension
Instructions for use
Product Description
Safety
Overvoltage protection
Installation
Lamp
Cleaning · Maintenance
Replacing the LED module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24 894 Ceiling and Wall Luminaire

Specifications

Type: Ceiling and Wall Luminaire
Material: Aluminium alloy, Aluminium, Stainless Steel
Protection Class: IP 65
LED Power Supply: 220-240 V x 0/50-60 Hz DC 176-280 V
Safety Class: I

Product Usage Instructions

Installation:

LEDs are high-quality electronic components. Avoid direct contact with the light output opening during installation or relamping. To remove the synthetic cover, unlock the 3 spring-locking mechanisms with a screwdriver. Lift off the synthetic cover. Loosen the 2 screws of the LED PCB to access the electrical connections. Secure the luminaire base onto the mounting surface using appropriate fixing materials. Make sure to connect the earth conductor and electrical supply cables.

Safety:

Installation and operation must comply with national safety regulations. Only a qualified electrician should perform installation and commissioning. Modifications to the luminaire should be handled by responsible individuals and not the manufacturer to avoid liability for improper use or damage.

Overvoltage Protection:

The luminaire’s electronic components are protected against overvoltage according to DIN EN 61547. For additional protection, consider separate overvoltage protection components available on the manufacturer’s website.

Bounce-Free Switching Contacts:

For optimal protection of electronic components, use bounce-free switching contacts like an electronic relay (solid-state relay). Recommended product: BEGA 71 320.

FAQ

Q: Can I install the luminaire myself?
- A: Installation and commissioning should only be performed by a qualified electrician to ensure compliance with safety regulations.
Q: How do I remove the synthetic cover?
- A: Unlock the 3 spring-locking mechanisms with a screwdriver and lift off the synthetic cover carefully.

Dimension

Instructions for use

Application

Unshielded ceiling and wall luminaire with high protection class. A luminaire made of die-cast aluminium and with an impact resistant synthetic diffuser.

Product Description

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Unidure® coating technology
Impact-resistant synthetic diffuser,
BEGA NeoGlass® · diffuse white
2 mounting holes ø 4.8 mm
Distance apart 160 mm
2 cable entries for through-wiring of mains supply cable ø 7-12 mm
Connecting terminal and earth conductor terminal 2.5@
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V 0/50-60 Hz
DC 176-280 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
CE Conformity mark
This product contains light sources of energy efficiency class(es) B

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping

The synthetic cover is fastened to the luminaire base via 3 spring-locking mechanisms. To remove the synthetic cover, unlock the 3 spring-locking mechanisms (as illustrated in the diagram) one after another by applying light pressure with a screwdriver. Lift off the synthetic cover. For mounting the luminaire base and the electrical connection, loosen the 2 screws (Torx drive T10) of the LED PCB and remove the LED PCB upwards (keyholes). While doing so, make sure that the LED PCB was not mechanically damaged. Lead the mains supply cable through the cable entry of the luminaire base. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface. Make the earth conductor connection and the electrical connection. In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.

Insert the LED PCB into the luminaire base and tighten the mounting screws uniformly. Make sure that gasket is positioned correctly. Guide the synthetic cover with the 3 mounting brackets into the recesses on the luminaire base and press down evenly until all 3 mounting brackets engage audibly.

Lamp

Module connected wattage 5.6 W
Luminaire connected wattage 6.5 W
Rated temperature ta = 25 °C
Service life criteria 50 000 h / L70

24 894 K3

Module designation LED-1598/830
Color temperature 3000 K
Color rendering index CRI > 80
Module luminous flux 1230 lm
Luminaire luminous flux 959 lm
Luminaire luminous efficiency 147,5 lm / W

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Close the luminaire.

Spares