BEGA 51 298.4 Wall Luminaire for Indoor Use Instruction Manual
- July 17, 2024
- BEGA
Table of Contents
BEGA 51 298.4 Wall Luminaire for Indoor Use
Specifications
- Lamp Module connected wattage: 34.8 W
- Luminaire connected wattage: 38.5 W
- Rated temperature: 25°C to 35°C
- Ambient temperature: 51 to 298.4 K3
- Colour temperature: 3000 K
- Colour rendering index (CRI): > 90
- Module luminous flux: 5400 lm
- Luminaire luminous flux: 3420 lm
- Luminaire luminous efficiency: 88.8 lm / W
Product Usage Instructions
Replacement Parts:
If replacement parts are needed, refer to the following:
- LED power supply unit: DEV-0305/700i
- LED module 3000 K: LED-1401/930, LED-1459/930
FAQ:
Q: Can I install the luminaire myself?
A: No, the installation and commissioning should only be done by a qualified
electrician.
Wall luminaire for indoor use
Instructions for use
Application
- Wall luminaire · Indoor luminaire with 2 ring-shaped light sources for unshielded and uniform light, light-diffusing silicone diffusers and metal rings.
- As single luminaires or in arrangements, they are creative lighting design solutions for interior design.
Product description
- Ring made of metal and luminaire housing made of synthetic material, surface Colour velvet brass
- Round inlay made of metal, finish Colour velvet brass
- Diffusor made of translucent ageing-resistant silicone
- Mounting plate with 2 fixing
- holes ø 6 mm · 85 mm spacing
- 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm, max. 5 G 1.5@ Connecting terminals 2.5@
Earth conductor connection
- Complies with flicker requirements in accordance with IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1 LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 196-250 V
DALI-controllable
- Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Conformity mark
- Weight: 1.2 kg
- This product contains light sources of energy efficiency class(es) D
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Lamp
- Module connected wattage 34.8 W
- Luminaire connected wattage 38.5 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 35 °C 51 298.4 K3
Module designation
- 1x LED-1401/930, 1x LED-1459/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 5400 lm
- Luminaire luminous flux 3420 lm
- Luminaire luminous efficiency 88,8 lm / W
Position the luminaire housing in a flat inclination angle over the
fastening edge of the mounting plate and swing in.
The luminaire can be rotated 350° on the mounting plate.
Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw
(wrench size 1.5).
Cleaning · MaSpares
- LED power supply unit DEV-0305/700i
- LED module 3000 K LED-1401/930
- LED module 3000 K LED-1459/9Spares
- LED power supply unit DEV-0305/700i
- LED module 3000 K LED-1401/930
- LED module 3000 K LED-1459/9intenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
- The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
- It is also listed in the spare parts overview at the end of these instructions for use.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools.
- Disconnect the system from the power supply. Undo the hexagon socket head screw (wrench size 2.5 mm) and remove luminaire from mounting plate.
- Remove the connecting lines from the terminals and place the front of the luminaire on a soft surface.
Open the luminaire housing:
Remove the 6 internal Torx screws (T20) and remove the bottom part of the
housing from the top part of the housing.
Disconnect the lines of the luminaire cable from the 4 terminals and remove
the terminals. Remove the LED module with the diffuser from the holder.
Install the replacement module. Please follow the installation instructions
for the new LED module.
A defective LED-module (silicone diffusor) must be replaced.
Close the luminaire housing:
- Guide the bottom part of the housing with the drilled hole over the positioning pin of the top part of the housing and place it on top. Retighten the 6 Torx screws (T20 max. 1.2 Nm). Re-attach the terminals to the wires of the luminaire cable.
- Make the electrical connection to the terminals. Observe the correct configuration of the connecting cable. Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
- The two connecting terminals marked DA, DA are provided for digital control purposes.
- If these terminals are not assigned, the luminaire will work with full light output. Position the luminaire housing in a flat inclination angle over the fastening edge of the mounting plate and swing in.
- Align luminaire housing and tighten (max. 0.25 Nm) hexagon socket screw (wrench size 1.5).
Spares
- LED power supply unit DEV-0305/700i
- LED module 3000 K LED-1401/930
- LED module 3000 K LED-1459/9
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>