ORTECH 2ALS-3CCT+W LED Architectural Strip Light Instruction Manual

: July 17, 2024
: Ortech

Table of Contents

2ALS-3CCT+W LED Architectural Strip Light
INPUT WIRING GROUP (OPTIONAL)
INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction Manual
LED Architectural Strip Light
MODEL 2ALS-3CCT+W | 4ALS-3CCT+W | 8ALS-3CCT+W

2ALS-3CCT+W LED Architectural Strip Light

WARNING
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY
A QUALIFIED ELECTRICIAN.

LED Strip lights are suitable for using in dry and damp locations
Please keep the LED Strip lights away from any corrosive substance, and please use dry cloth when you clean it.
LED Strip lights can only be installed by a qualified electrician
Before installation or maintenance, please disconnect the power to prevent electric shock
DO NOT cover fixture with insulation liner Or similar material.

CAUTION

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.

Remove the cover from the L-Connector.
Remove the end cap and upper cover from fixture.
Slide the splicing bracket B into locating piece, then loci it with screws.
Make the mounting marks on the ceiling for fixtures, please refer to pendant mounting for suspending the fixture.
Adjust the lifting bracket in the fixture to a suitable position for suspending and linking, BOX CONTENTS WIRING 1. If dimming is not used, please separate the dimming wires with nuts.
2. Wiring must follow up the wiring diagram.
3. Remind again: Cut off the power supply before operation.
Insert the L -Connector into the fixtures as shown below, and pull the lock buckle to splice fixtures.
Make electrical connection of fixture and X-Connector with male-female connectors.
Cut off the connectors in one of the ends for wiring to line voltage.
Screw back the cover of L -Connector, lock back the fixture upper cover, lock back the other end of fixture upper cover.
Wire fixtures according to wiring diagram.
Installation complete.

WIRING

If dimming is not used, please separate the dimming wires with nuts.
Wiring must follow up the wiring diagram.
Remind again: Cut off the power supply before operation

INPUT WIRING GROUP (OPTIONAL)

Wire according to the wiring diagram on the left for completion.

INSTRUCTIONS

Remove the cover from the T-Connector.
Remove the end cap ond upper cover from fixture.
Slide the splicing bracket B into locating piece, then loci it with screws.
Make the mounting marks on the ceiling for fixtures, please refer to pendant mounting for suspending the fixture.
Adjust the lifting bracket mn the fixture to a suitable position for suspending and linking. BOX CONTENTS WIRING
****1 If dimming is not used, please separate the dimming wires with nuts.
2. Wiring must follow up the wiring diagram.
3.Remind again: Cut off the power supply before operation.
Insert the L -Connector into the fixtures as shown below, and pull the lock buckle to splice fixtures.
Make electrical connection of fixture and T-Connector with male-female connectors.
Cut off the connectors in one of the ends for wiring to line voltage.
Screw back the cover of T-Connector, lock back the fixture upper cover, lock back the other end of fixture upper cover.
Wire fixtures according to wiring diagram.
Installation complete.
Remove the cover from “L”joiner.
Remove the end cap and upper cover from fixture.
Slide the splicing bracket B into locating piece, then lock it with screws.
Make the mounting marks on the ceiling for fixtures, pleas refer to pendant mounting instructions for suspending the fixture.
BOX CONTENTS
Insert the “L” joiner into the fixture as shown below, and pull the lock buckle to splice the fixtures.
Make electrical connection with male-female connectors.
Cut off the connectors in one end for wiring to line voltage
Screw back the cover of “V”joiner, lock back the fixture upper cover, Lock back the other end of fixture upper cover
Make wiring according to diagram
Installation completed.

WIRING

INSTRUCTIONS

Remove the cover from the X-Connector.
Remove the end cap and upper cover from fixture
Slide the splicing bracket B into locating piece, then loci it with screws
Make the mounting marks on the ceiling for fixtures, please refer to pendant mounting for suspending the fixture.
Adjust the lifting bracket in the fixture to a suitable position for suspending and linking. BOX CONTENTS WIRING 1. If dimming is not used, please separate the dimming wires with nuts.
2. Wiring must follow up the wiring diagram.
3. Remind again: Cut off the power supply before operation.
Insert the X-Connector into the fixtures as shown below, and pull the lock buckle to splice fixtures.
Make electrical connection of fixture and X-Connector with mole-female connectors.
Cut off the connectors in one of the ends for wiring to line voltage.
Screw back the cover of X-Connector, lock back the fixture upper cover, lock back the other end of fixture upper cover.
Wire fixtures according to wiring diagram.
Installation complete.
Remove the top cover and side cover from one end of the fixture .
Loosen the screws and remove the sensor cover.
Plug the end-cap sensor module into the fixture
Connect the wires of the same color through male-female connectors or wire nuts
Lock the sensor cover and fixture top cover.
Installation completed.

BOX CONTENTS

Reference	QTY.	Remarks	Project:
		Location:
		Architect:
		Engineer:
		Contractor:
		Submitted by:
		Date:

ORTECH reserves the right to modify at any time, without notice, any or all of our product’s features, designs, components and speciﬁcations to meet market changes.

info@ortechindustries.com
www.ortechindustries.ca
13376 Comber Way
Surrey BC V3W 5V9
205 Summerlea Rd,
Brampton, ON L6T 4E5
1-888-543-6473
1-888-541-6474