ORTECH SL-RGB25M LED Strip Lights Instruction Manual
- May 15, 2024
- Ortech
Table of Contents
ORTECH SL-RGB25M LED Strip Lights
PRODUCT VIEW
SAFETY INSTRUCTIONS
WARNING
WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.
- LED Strip Lights are suitable for using in dry, damp and/or *wet locations
- Please keep the LED Strip Lights away from any corrosive substance, and please use dry cloth when you clean it
- LED Strip Lights can only be installed by a qualified electrician
- Before installation or maintenance, please disconnect the power to prevent electric shock
Depending on your grade of protection choice, suitable location may differ
Application Notice
- Installation MUST be installed in accordance with applicable electrical codes by a qualified electrician
- DO NOT turn LEDs on when still on reel. The lights MUST be pulled out
- DO NOT secure strip lights with nails or staples
- ONLY cut LED strip at designated cut lines
CAUTION
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE
REFERENCES.
Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a
competent electrician.
INSTALLATION GUIDE
-
Measure area needed for strip light installation.
Cut the LED strip to the length at the closest cut line. Peel 3M TAPE off back of the strip -
Press strip firmly in place with 3M tape backing.
Double confirm the wattage and length of strip to choose a power supply that is larger than the total -
Make sure to follow wire colours from the LED strip to the RGB controller.
Ensure that the (+) and (-) wires are followed between the power supply and controller -
Cut as needed lengths of strip lighting off the roll. Use easy connectors as new power line by sliding strip under contacts on connectors and making sure contacts match solder points as well as match colours
NOTE:
Use a 12V DC LED power supply ONLY.
12V AC will damage the controller and LEDs quickly
CONTROL UNIT
RF 20m effective control
Intelligent switch
20 main modes
15 music modes
Touching colour chooser
Wake-up induction
LED backlight
The 3.5MM audio
INTERFACE
RGB25M-REMOTE
- ON. Keep pressing 3 seconds, LED Strip will be white light
- OFF.
- RGB light colour selecting ring
- Adjustable brightness
- Changing speed / Colour temperature adjust
- Operating mode
- Music mode
RGB25M-CONTROL
- Sensitive adjust knob
- Audio input port
- 12-24V DC input
- Audio receiver
- Output (2 channels)
CODE MATCHING
RGB25M-REMOTE
Default Code: One remote can control multi controllers
If you want to match a remote to one certain controller, you need to match the code of this remote to the controller
Below shows you how to match the codes:
-
Power on the controller, and within 5 seconds, synchronously press the 2 keys on the remote.
(see the picture on the left) -
When the code matches successfully, the strip light would triple flicker
Operating Mode
| Mode Info | Mode Introducing | Remark |
|---|---|---|
| Static Single Colour | N/A | Static Lighting Mode |
| RGB Jumping | Jumping speed is adjustable |
7 colours Jumping
3 colours Gradual Changing| Changing speed is adjustable
7 colours Gradual Changing
Single Colour Flashing| Flashing speed is adjustable
RB Gradual Altering| The speed is adjustable
RG Gradual Altering
GB Gradual Altering
Random Colours Jumping
Single Colour Light vs Music| Brightness and Speed is changing per Music|
Dynamic Mode (Music Control)
7 colours Jumping vs Music| Brightness, Speed and Colour is changing per Music
CONNECTING SET UP
ORTECH reserves the right to modify at any time, without notice, any or all of our product’s features, designs, components and specifications to meet market changes.
Customer Support
[email protected]
www.ortechindustries.ca
13376 Comber Way
Surrey BC V3W 5V9
205 Summerlea Rd
Brampton, ON L6T 4E5