ORTECH OE-212 LED Emergency Light Instruction Manual

ORTECH OE-212 LED Emergency Light

Specifications

• Product: LED Emergency Lights
• Model: OE-212
• Indoor Use Only
• Max Mounting Height: 16.2ft (4.9m)

Product Usage Instructions

Installation Guide

Wall Mount Installation

1. Press the buttons to take out the back plate from the fixture
2. Remove knockout on back plate and mount J-Box to backplate
3. Knockout center of backplate and feed wires through hole
4. Secure backplate to J-Box
5. Connect J-Box wires to power supply wires using the wire nuts provided. Connect the WHITE wire to NEUTRAL: If using 120V, connect the BLACK wire to hot lead. If using 277V, connect the RED wire to hot lead. Cap unused lead. Place wires into J-Box (refer to the wiring diagram)
6. Snap front cover onto backplate
7. Restore power and press test button. LED heads will turn ON
8. Adjust lamp heads and lens direction as per your needs

Ceiling Mount Installation

1. Mount back plate on ceiling surface
2. Feed building AC supply wire through backplate
3. Connect fixture power supply wires using wire nuts provided

FAQ

• Q: Can LED Emergency Lights be used outdoors?
  A: No, LED Emergency Lights are for indoor use only.

• Q: How long should the battery charge before first use?
  A: Allow the battery to charge for 24 hours before first use.

• Q: What should I do before installation or maintenance?
  A: Before installation or maintenance, please disconnect the power to prevent electric shock.

• Q: Can I install LED Emergency Lights myself?
  A: No, LED Emergency Lights can only be installed by a qualified electrician.

LED Emergency Lights
MODEL OE-212

WARNING

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

1. LED Emergency Lights are for INDOOR USE ONLY
2. Please keep the LED Emergency Lights away from any corrosive substance, and please use dry cloth when you clean it
3. LED Emergency Lights can only be installed by a qualified electrician
4. Before installation or maintenance, please disconnect the power to prevent electric shock

Application Notice

1. All electrical connections MUST be in accordance with local codes, ordinances and the National Electric Code
2. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel
3. The use of accessory equipment is not recommended by the manufacturer. DO NOT use the Emergency Light other than intended use
4. Replace the batteries as needed according to ambient conditions. We recommend the equipment be tested regularly in accordance with local codes
5. Press the test button, the LED heads will turn ON and the LED indicator will turn OFF. Release the test switch, LED indicator will turn ON and the LED heads OFF
6. If LED heads or indicator does not illuminate, check:
7. AC supply, verify the unit has 24 hours of AC supply
8. Unit is shortened or battery not connected
9. Battery discharge. Permit unit to charge for 24 hours then re-test
10. DO NOT mount in hazardous locations or near gas or electric heaters. DO NOT let power cords touch hot surfaces
11. Disconnect power at fuse or circuit breaker before installing or servicing
12. Allow battery to charge for 24 hours before first use

CAUTION

• PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES. Electrical products can cause death or injury, or damage to property.
• If in any doubt about the installation or use of this product, consult a competent electrician.

INSTALLATION GUIDE

Wall Mount Installation

Max Mounting Height : 16.2ft (4.9m)

1. Press the buttons to take out the back plate from the fixture

2. Remove knockout on back plate and mount J-Box to backplate

3. Knockout centre of backplate and feed wires through hole

4. Secure backplate to J-Box

5. Connect J-Box wires to power supply wires using the wire nuts provided.
   Connect the WHITE wire to NEUTRAL:

6. If using 120V, connect the BLACK wire to hot lead.

7. If using 277V, connect the RED wire to hot lead. Cap unused lead. Place wires into J-Box (refer to the wiring diagram on the right)

8. Snap front cover onto backplate

9. Restore power and press test button. LED heads will turn ON

10. Adjust lamp heads and lens direction as per your needs

Ceiling Mount Installation

Refer to wall mount installation instruction on the left:

1. Mount back plate on ceiling surface
2. Feed building AC supply wire through backplate
3. Connect fixture power supply wires using wire nuts provided

ORTECH reserves the right to modify at any time, without notice, any or all of our product’s features, designs, components and specifications to meet market changes.

info@ortechindustries.com
www.ortechindustries.ca
13376 Comber Way Surrey BC V3W 5V9
205 Summerlea Rd Brampton, ON L6T 4E5
1-888-543-6473
1-888-541-6474

References

• Led Lighting, Electrical and Hvac Supplier Ortech Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>