ORTECH SLIM4GIM LED Slim Lights Instruction Manual

ORTECH SLIM4GIM LED Slim Lights

Specifications:

• Model: SLIM4GIM
• Usage: Indoor use only
• Power Supply: Electric
• Compatibility: Compatible with specific dimmers and mounting plates

Product Usage Instructions

Pre-Installation:

1. Turn off power from the electrical panel before starting installation.
2. Locate a suitable position for the fixture and open according to cut-hole dimensions.
3. Run electrical wire from the switch through the mounting hole using NMD90 Romex or BX cable.

Driver Wiring:

1. Open the hardwire box swing cover and remove appropriate knockout(s).
2. Insert the electrical supply cable through the knockout and secure with a cable connector.
3. Connect ground, white, and black wires accordingly (refer to fig.1).

Fixture Installation:

1. Connect the fixture to the hardwire box by twisting male/female connectors.
2. Insert the fixture base into the mounting hole and release spring-loaded clips to secure it flush to the ceiling.
3. Turn on power to confirm proper functionality of the fixture.

FAQ

Q: Can LED Slim Lights be used outdoors?

A: No, LED Slim Lights are suitable for indoor use only. Using them outdoors may cause damage.

Q: Do I need a qualified electrician to install LED Slim Lights?

A: Yes, LED Slim Lights can only be installed by a qualified electrician to ensure safety and proper installation.

Q: What should I do if I have doubts about installing the product?

A: If you are unsure about installation or usage, consult a competent electrician for assistance to prevent any risks.

MODEL SLIM4GIM

WARNING

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED ELECTRICIAN.

1. LED Slim Lights are suitable for indoor use only. DO NOT use outdoors
2. Please keep the LED Slim Lights away from any corrosive substance, and please use damp or dry cloth when you clean them
3. LED Slim Lights can only be installed by a qualified electrician
4. Before installation or maintenance, please disconnect the power to prevent electric shock

Application Notice

1. For your safety, this fixture must be wired in accordance to local electrical codes and ordinances
2. Make certain power is OFF from the electrical panel before starting installation or attempting any maintenance

CAUTION
PLEASE READ INSTRUCTIONS BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCE. Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or use of this product, consult a competent electrician.

Tools Required

• Saw
• Measuring Tape
• Electrical Wiring (use type and gauge suitable for application to connect the fixtures)

Pre-Installation

1. Turn power OFF from the electrical panel before starting the installation
2. Locate a suitable position to place the fixture and open in accordance to the cut-hole dimensions (refer to HOLE CUT SIZE TABLE below for the appropriate size)
3. Run electrical wire from the switch (power supply) through the mounting hole — use NMD90 Romex or BX cable

Compatible Dimmers Table

Compatible Mounting Plates Table

INSTALLATION GUIDE

Driver Wiring

1. Open the hardwire box swing cover and remove the appropriate knockout(s)

2. Insert the electrical supply cable through the knockout and secure with a cable connector (sold separately)

3. Using wire nuts, connect GREEN ground wire of cable to GREEN wire on box.
   Connect WHITE wire of cable to WHITE wire of box. Connect BLACK wire of cable to BLACK wire of box (see fig.1)

4. Place all wiring and connections back into the box and close the cover

5. Insert hardwire box through the mounting hole (see fig.2)

New Construction Applications
Hardwire box shall be firmly secured to studs, joists, or similar fixed structural units

Remodel Applications
DO NOT require the hardwire box to be firmly secured after the mounting plates, studs, joists, or structural units have been concealed

Fixture Installation

1. Connect the fixture to the hardwire box by inserting and twisting the male/female connectors (see fig.3)
2. Push spring-loaded clips on the fixture upwards and insert fixture base into the mounting hole. Release the clips and fixture will be pulled flush to the ceiling (see fig.4)
3. Once assembly is complete, turn on power to confirm fixture is working properly

info@ortechindustries.com
www.ortechindustries.ca

13376 Comber Way Surrey BC V3W 5V9

205 Summerlea Rd Brampton, ON L6T 4E5

1-888-543-6473
1-888-541-6474

References

• Led Lighting, Electrical and Hvac Supplier Ortech Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>