LEXON LH94 Lantern User Guide

LEXON LH94 Lantern

Product Usage Instructions

Setting up the Lamp and Wireless Charger

1. Connect the lamp to a power source with sufficient power.
2. Place your Qi-enabled device face up at the center of the wireless charging surface.

Using the Wireless Charging Feature

When the wireless charging is initiated, the following LED indicators will show different statuses:

• Insufficient power input: LED lamp flashing slowly in orange.
• Foreign Object Detected: Left LED is RED and blinking quickly.
• Battery charging: Right LED is RED.
• Fully charged: Right LED turns OFF.

Once your device is properly positioned and charging, the left LED will turn blue for 30 seconds then turn off.

Customizing Light Settings

To set Lantern in cool and warm light mode only, quickly tap 3 times on the touch area (3). To return to full set lighting mode, repeat the procedure.

FAQ

• Q: Is Lantern compatible with all devices?
• A: Lantern is compatible with all Qi-enabled devices.
• Q: What should I do if the LED indicators show specific colors?
• A: Refer to the user manual for detailed information on the meaning of LED indicator colors and actions to take.

IN THE BOX

• 1x LED lamp with built-in Qi wireless charger
• 1x USB-C cable
• 1x User manual

PRODUCT OVERVIEW

1. Lighting surface
2. Wireless charging surface
3. Touch button
4. LED indicator for charging status
5. Input port
6. LED indicator for wireless charging status

LAMP FEATURES

• Turn ON the lamp by touching the touch button (3).
• Change the light color (9 colors options) by simply touching the touch button (3).
• Adjust the brightness by pressing and holding the touch button (3).
• To turn OFF the light, wait 3 seconds after the color selection then touch (3) again.

The last color set will be remembered for next time.
Note: If you want to set Lantern in cool and warm light mode only, quickly tap 3 times on the touch area (3). To return to full set lighting mode, repeat the procedure.

WIRELESS CHARGING

• Important note: To get your Lexon device properly operating, make sure to use a DC 9V-2A power adapter (not included) or a Quick Charge 3.0 power adapter (not included).
• To enjoy fast wireless charging* at 15 W, make sure you use a USB power adapter that delivers at least 30 W.
• If the input power is insufficient, the lamp will flash slowly in orange.
• Only mobile devices that support wireless charging can be charged using this feature. Charging speed or efficiency may vary depending on the environment, the device being charged and its battery capacity.

Lantern is compatible with all Qi-enabled devices.

1. Make sure your lamp is connected to a power source that delivers sufficient power.
2. Place the mobile device supporting wireless charging face up at the center of the wireless charging surface.
    | LEDs (4/6) & Lamp (1) indicators
   ---|---
   Wireless charging initiated| The left LED is BLUE for 30 seconds
   Insufficient power input| LED lamp starts flashing slowly in orange
   Foreign Object Detected| The left LED is RED and starts blinking quickly
   Battery charging| The right LED is RED
   Fully charged| Right LED turns OFF
3. Once the mobile device is properly positioned and charging, the left LED on the back of the lamp will turn blue for 30 seconds then turn off.

SAFETY PRECAUTION

• The light source of the lamp is an integrated LED module. Do not attempt to modify or disassemble this lamp in any way.
• Place the lamp on a dry and flat surface.
• Do not place your lamp in very hot or cold areas.
• Always clean the product with a soft cloth and do not use any cleaning materials that contain chemicals.
• Do not put metal objects or magnets between the mobile device and the wireless charging surface.
• Never place your device in water to avoid causing internal short-circuit, overheating, fire, deformation, or even explosion of the battery.
• Keep your device out of reach of small children to prevent danger.
• Do not attempt to service, repair, or disassemble the lamp or the supplied cable yourself.
• Lexon cannot be held responsible for any malfunctions or damages resulting from failure to adhere to these instructions properly.

PRODUCT SPECIFICATIONS

• Material: Synthetic leather / ABS
• Weight: 1.01 lbs / 461 g
• Dimensions: 5.67 x 5.67 x 8.35” / 14.4 x 14.4 x 21.2 cm
• Max. lumen output: 100 lm
• Light power: 5W max
• Color temperature:
  • Warm white: 3000K
  • Cold White: 6800K
• Input port: 9V-2A, Quick Charge 3.0 Power Adapter (not included), or a DC 9V/2A Power Adapter (not included).
• Wireless charging output: Up to 15W
• Battery type: Li-ion 5000 mAh
• Battery voltage: 3.7V
• Battery life: Up to 8 hours for light only*
• Charging time (USB Type-C): 4 hours
• Operating temperature: 0°C – 35°C
• international Warranty: 1 year

*varies according to product use, set light intensity and selected light color

EUROPEAN UNION CE DIRECTIVE

• LEXON hereby declares that these devices follow the essential requirements and other relevant provisions of directives 2014/53/EU, 2014/30/EU & 2012/19/EU.
• The original EU declaration of conformity may be found at: https://www.lexon-design.com/assets/certifications-ce-lantern.pdf.

UK CONFORMITY ASSESSMENT

• The object described above conforms with the essential requirements and other relevant provisions of the UK Radio Equipment Regulations 2017(SI 2017/1206).
• This device was tested for uncontrolled environment operations. To comply with RF exposure requirements, a minimum separation distance of 20 cm must be maintained between the user’s body and the device.
• The original UK declaration of conformity may be found at:
• https://www.lexon-design.com/assets/certifications-ukca-lantern.pdf
• Radiated H-Field: -13.81 dBuA/m(@10m) (for EU/UK only)
• TX/RX Frequency Range: 110-148 KHz (for EU/UK only)

DISPOSAL AND RECYCLING INFORMATION
After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies: electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic device at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

FCC STATEMENT

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed. and operated with a minimum distance of 20cm between the radiator and your body.

Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-0003.

RF exposure statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 10 cm between the radiator and your body.

CONTACT

• 125, Avenue des Champs-Elysées – 75008 Paris – FRANCE
• All brands or product names are or may be trademarks or their respective owners.
• Pictures and specifications are not contractual. Assembled in China.
• lexon-design.com. @lexondesign

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>