BEGA 85 250 Garden and Pathway Luminaire Instruction Manual

BEGA 85 250 Garden and Pathway Luminaire

Specifications

• Module connected wattage: 3.9 W
• Luminaire connected wattage: 4.8 W
• Module designation: LED-1559/83040
• Colour rendering index (CRI) : > 80
• Recommended light point interval : 7 m
• Operating voltage : 220-240 V AC, 50-60 Hz
• Protection class: I
• IP rating : IP65
• Wireless connectivity: Zigbee 3.0, Bluetooth 5.0
• Compliance: IEEE 1789, DIN IEC/TR 63158, DIN IEC/TR 61547-1

Product Usage Instructions

Control Options:
The luminaire can be controlled via a switched phase for classic on/off functionality. Alternatively, it can be controlled via a continuous phase using the BEGA Smart app or in conjunction with  the wibutler pro (2nd Gen.) and the wibutler app.

Color Temperature and Brightness Adjustment:
The color temperature of the luminaire can be set to either 3000 K or 4000 K. The brightness of the luminaire can also be adjusted.  The default settings are 3000 K and maximum brightness.

Installation:
The luminaire is made of cast aluminum, aluminum, and stainless steel. It features opal glass with a screw neck and a silicone gasket. The luminaire should be mounted on a foundation created by the customer or on other paved surfaces using the provided steel mounting base with 3 fixing holes.

Wireless Connectivity:
The luminaire supports wireless control via smartphone or tablet using radio frequency at 2.4 GHz. It is equipped with Zigbee 3.0 and Bluetooth 5.0 for seamless connectivity.

DIMENSION

Application

Unshielded garden and path luminaire with rotationally symmetrical light distribution. Suitable for private and public areas in which there is no risk of vandalism. The luminaire can be controlled via a switched phase classically on/off or with a continuous phase either via the BEGA Smart app or in combination with the butler pro (2. Gen.) with the butler app. The color temperature can be set optionally 3000 K and 4000 K, and the luminaire brightness can be adjusted. The default factory settings are 3000 K and maximum brightness.

Lamp

• Module connected wattage 3.9 W
• Luminaire connected wattage 4.8 W
• Module designation LED-1559/83040
• Colour rendering index CRI > 80
• Rated temperature ta = 25 °C
• Service life criteria 50 000 h / L70
• Operation at colour temperature 3000 K
• Module luminous flux 725 lm
• Luminaire luminous flux * 463 lm
• Luminaire luminous efficiency * 96,5 lm / W Operation at colour temperature 4000 K
• Module luminous flux 735 lm
• Luminaire luminous flux * 466 lm
• Luminaire luminous efficiency * 97,1 lm / W

Lighting technology
Recommended light point interval 7 m

Product Description

• Luminaire made of cast aluminum, aluminium and stainless steel
• BEGA Unidure® coating technology
• Colour graphite or silver
• Opal glass with screw neck
• Silicone gasket
• Luminaire with a mounting base made of hot-dip galvanized steel according to EN ISO 1461 for bolting onto a foundation provided by the customer or on other paved surfaces such as terraces and paving stones
• Base plate with 3 fixing holes ø 9 mm · Pitch 120° · Pitch circle ø 65 mm
• Mounting bracket with connection box and 3-pole terminal 4@ for connection of
• mains supply cable max. 3 × 2.5@
• Data matrix code for convenient configuration via smartphone or tablet
• Radiofrequency 2.4 GHz
• Maximum output +6 dBm
• Zigbee 3.0 and Bluetooth 5.0
• Complies with flicker requirements in accordance with IEEE 1789,
• DIN IEC/TR 63158, DIN IEC/TR 61547-1
• LED power supply unit 220-240 V x 0/50-60 Hz
• DC 176-280 V
• BEGA Thermal Switch®
• Temporary thermal shutdown to protect temperature-sensitive components
• Safety class I
• Protection class IP 65
• Dust-tight and protection against water jets
• Conformity mark
• This product contains light sources of energy efficiency class(es)

EU Declaration of Conformity
BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 85 250 complies with Directive 2014/53/EU (RED). The complete text of the EU Declaration of Conformity is available at the following Internet address: https://www.bega.com/conf/de/85250

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Range

The Zigbee radio range between individual devices is usually 30 m, with ambient conditions playing a decisive role. Bluetooth generally has a range of 12 m, whereby environmental conditions and the end device used (e.g. smartphone) play a decisive role.

IMPORTANT:
The enclosed data matrix-code labels are required for initial setup of the luminaires. Please save these labels with the assigned specifications for the installation site (room description, location, etc.) with your documentation (e.g. instructions for use top of Page 1).

Installation

• LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
• The base of the luminaire must not be below top edge of the ground surface.
• A cable length of 400 mm above the ground surface is required for the electrical connection of the luminaire.
• Remove the mounting base from the luminaire by undoing the screws at the base of the luminaire.
• Lead underground cable from below in the mounting base.
• Fix the mounting base with enclosed or any other suitable fixing material onto the mounting surface.
• Open the connection box.
• Lead the luminaire wiring and mains supply cable into the connection box.
• Make the earth conductor connection and the electrical connection.
• Close the connection box.
• Lead the bollard tube over the mounting base and align.
• Tighten the screws evenly.

Screw the glass with the gasket into the luminaire housing and tighten firmly. Make sure that the glass gasket is seated correctly (see sketch).

Initial setup
For successful configuration, the luminaires should start in their factory settings. If the installation is not carried out correctly, or access via the BEGA Smart or wibutler apps is no longer possible, the luminaire should be reset to factory settings.

Reset to factory settings
The luminaire must be switched off five times (for at least 3 seconds each time) to manually reset it to factory settings (see sketch). The luminaire can also be reset to the factory settings via the BEGA Smart or wibutler apps.

Download app

bega.com/bega-smart-ios

bega.com/bega-smart-android

Control using a switched phase

When the luminaire is to be activated and deactivated with classic on/off controls via a switched phase, the color temperature and brightness can be set permanently in the BEGA Smart app under “Configure start-up behaviour” once the luminaire is switched on. The app can find the luminaire for 30 minutes after switch-on, provided it is within the immediate vicinity of the smartphone.

Integration into a BEGA Smart system
When integrating the luminaire into a BEGA Smart system (required for variable adjustment of color temperature and brightness, integration into groups, scenarios, automation etc.), it must be connected to a continuous phase (Pstandby = 0.25 W). In the BEGA Smart app, either select “Create new system” or add a new device to your existing system. Then select “Smart luminaires” and follow the instructions.

Integration into a wibutler system
When integrating the luminaire into a wibutler system), it must be connected to a continuous phase (Pstandby = 0.25 W). A butler system enables combinations with products from other manufacturers and systems, integration into voice assistants as well as remote access. One configured wibutler per parent system is required along with the wibutler app. Then select “Add devices” in the app under “Manufacturer: BEGA” and follow the instructions.

For more information go t o: www.wibutler.com

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.  To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com. The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets. Defective glass must be replaced. Close the luminaire.

Accessory

71 895 wibutler pro (2. Gen.)
Using wibutler pro, BEGA Smart components can easily be integrated into a Professional Smart Home alongside third-party products using wibutler pro.

Spares

• LED power supply unit DEV-0487/24V
• Smart Dim SW – Platine 61 002 199
• LED module LED-1559/83040
• Glass graphite 75 005 207
• Glass silver 75 005 208
• Gasket glass 83 001 996

BEGA Gantenbrink-Leuchten KG

• Postfach 31 60
• 58689 Menden
• info@bega.com 
• www.bega.com

FAQ

Q: Can the color temperature of the luminaire be adjusted?
A: Yes, the color temperature can be set to either 3000 K or 4000 K.

Q: How is the luminaire controlled?
A: The luminaire can be controlled via a switched phase for on/off functionality or through a continuous phase using the BEGA Smart app or wibutler pro (2nd Gen.) with the wibutler app.

References

• BEGA Smart - Apps on Google Play
• ‎BEGA Smart on the App Store
• BEGA · Das gute Licht.
• DBT Digital Building Technology | wibutler IoT-Plattform

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>