BEGA 24920 Wall Luminaire Instruction Manual

: July 15, 2024
: BEGA

Table of Contents

BEGA 24920 Wall Luminaire
DIMENSION
SPECIFICATION
Installation
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24920 Wall Luminaire

Specifications

Material: Aluminium alloy and thick-walled crystal glass
Control Options: Switched phase on/off, continuous phase via BEGA Smart app or Wibutler Pro with butler app
Color Temperature: 3000 K and 4000 K
Brightness: Adjustable with default settings at 3000 K and maximum brightness
Module Connected Wattage: 5.6 W
Luminaire Connected Wattage: 6.7 W
Module Designation: LED-1555/83040
Color Rendering Index ( CRI): > 80
Service Life Criteria : 50,000 hours / L70

DIMENSION

Application

Wall luminaire made of aluminum alloy and thick-walled crystal glass.
The luminaire can be controlled via a switched phase classically on/off or with a continuous phase either via the BEGA Smart app or in combination with the butler pro (2. Gen.) with wibutler app.
The color temperature can be set optionally to 3000 K and 4000 K, and the luminaire brightness can be adjusted.
The default factory settings are 3000 K and maximum brightness.

Product Description

Luminaire made of aluminum alloy,
aluminum and stainless steel
BEGA Unidure® coating technology
Crystal glass, white inside
Silicone gasket
2 mounting holes ø 6 mm
Distance apart 140 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connection terminal 2.5@
Earth conductor connection
Data matrix code for convenient configuration via smartphone or tablet
Radiofrequency 2.4 GHz
Maximum output +6 dBm
Zigbee 3.0 and Bluetooth 5.0
Complies with flicker requirements under IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1 LED power supply unit
220-240 V 0/50-60 Hz
DC 176-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
CE – Conformity mark
This product contains light sources of energy efficiency class(es) C

EU Declaration of Conformity
BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 24 920 complies with Directive 2014/53/EU (RED). The complete text of the EU Declaration of Conformity is available at the following Internet address:
https://www.bega.com/conf/de/24920

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at: www.bega.com.

The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320.

Range
The Zigbee radio range between individual devices is usually 30 m, with ambient conditions playing a decisive role.
Bluetooth generally has a range of 12 m, whereby environmental conditions and the end device used (e.g. smartphone) play a decisive role.

IMPORTANT
The enclosed data matrix-code labels are required for the initial setup of the luminaires. Please save these labels with the assigned specifications for the installation site (room description, location, etc.) with your documentation (e.g. instructions for use top of.

SPECIFICATION

Lamp

Module connected wattage 5.6 W
Luminaire connected wattage 6.7 W
Module designation LED-1555/83040
Colour rendering index CRI > 80
Rated temperature ta = 25 °C
Service life criteria 50 000 h / L70
Operation at colour temperature 3000 K
Module luminous flux 1160 lm
Luminaire luminous flux * 650 lm
Luminaire luminous efficiency * 97 lm / W
Operation at colour temperature 4000 K
Module luminous flux 1195 lm
Luminaire luminous flux * 666 lm
Luminaire luminous efficiency * 99,4 lm / W
- preliminary data

Installation

LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the screws and lift off the luminaire top. Disconnect the plug-connection of the LED connecting cable.
Disconnect the earth conductor connection from the plug connection.
Lead the main supply cable through the cable entry of the luminaire base.
Note the position of application of the luminaire “arrow down”.
Fix the luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make an earth conductor connection.
Push silicone sleeves over the lines and make an electrical connection.
To guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
Connect the green and yellow protective earth conductor from the luminaire top to the terminal marked in the luminaire base.
Make sure that the gasket is positioned correctly. Install the luminaire top, press on and
tighten screws evenly.

Initial setup

For successful configuration, the luminaires should start in their factory settings.
If the installation is not carried out correctly, or access via the BEGA Smart or Wibutler apps is no longer possible, the luminaire should be reset to factory settings.

Reset to factory settings

The luminaire must be switched off five times (for at least 3 seconds each time) to manually reset it to factory settings (see sketch).
The luminaire can also be reset to the factory settings via the BEGA Smart or Wibutler apps.

Control using a switched phase

When the luminaire is to be activated and deactivated with classic on/off controls via a switched phase, the colour temperature and brightness can be set permanently in the BEGA Smart app under “Configure start-up behaviour” once the luminaire is switched on. The app can find the luminaire for 30 minutes after switch-on, provided it is within the immediate vicinity of the smartphone.
Integration into a BEGA Smart system When integrating the luminaire into a BEGA Smart system (required for variable adjustment of colour temperature and brightness, integration into groups, scenarios, automations etc.), it must be connected to a continuous phase (Pstandby = 0.25 W).
In the BEGA Smart app, either select “Create new system” or add a new device to your existing system.
Then select “Smart luminaires” and follow the instructions.

Integration into a wibutler system

When integrating the luminaire into a wibutler system), it must be connected to a continuous phase (Pstandby = 0.25 W).
A wibutler system enables combinations
with products from other manufacturers and systems, integration into voice assistants as well as remote access.
One configured wibutler per parent system is required along with the wibutler app.
Then select “Add devices” in the app under
“Manufacturer: BEGA” and follow the instructions.
For more information go to: www.wibutler.com

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.

Accessory

71 895 wibutler pro (2. Gen.)
Using wibutler pro, BEGA Smart components can easily be integrated into a Professional Smart Home alongside third party products using wibutler pro.

Spares

Spare glass 11 003 163 11
LED power supply unit DEV-0487/24V
Smart Dim SW – Platine 61 002 199
LED module LED-1555/83040
Gasket 83 001 572

BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com

FAQ

Q: Can I adjust the color temperature and brightness of the luminaire?
- A: Yes, you can set the color temperature to either 3000 K or 4000 K and adjust the brightness as needed.
Q: What is the recommended service life of the LED module?
- A: The LED module has a rated service life of 50,000 hours at L70 criteria.