BEGA 50 916.2 Table Lamps Instruction Manual
- June 3, 2024
- BEGA
Table of Contents
BEGA 50 916.2 Table Lamps
Application
- Table lamp · indoor luminaire with wide beam light distribution.
- Luminaire for positioning on a wooden base for a variety of lighting situations with adjustable light.
- Wooden base optionally available in three different colour versions, as listed below.
Product description
- Table lamp »STUDIO LINE«
- Die-cast aluminium luminaire housing, velvet black finish, inside hue matt aluminium
- Trim ring · Chrome finish
- Clear safety glass
- Light-diffusing silicone lens
- Reflector made of pure anodised aluminium Cable dimmer (touch-controlled dimmer) for infinite light adjustment
- Black connecting cable · 2500 mm, with safety socket
- LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 196-250 V
- Safety class I
- c – Conformity mark
- Weight: 1.8 kg
Safety
- The installation and operation of this luminaire are subject to national safety regulations.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
- To achieve an additional protection against
- e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at www.bega.com.
Lamp
- Module connected wattage 11.5 W
- Luminaire connected wattage 13.5 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 55 °C
50 916.2 K3
- Module designation LED-0978/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 1735 lm
- Luminaire luminous flux 1072 lm
- Luminaire luminous efficiency 79,4 lm / W
Installation
- LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
- For precise positioning of reflector and cover ring, it is advisable to lift the luminaire at the connecting cable. The opening of the luminaire housing points downwards.
- Screw enclosed trim ring with attached reflector into the luminaire housing by turning it clockwise.
- Position luminaire on the separate wooden base. Insert the connecting cable into the groove of the wooden base.
- For this purpose, wooden bases in three different surfaces are available – accessories 13 209, 13 208 and 13 277.
- Connect luminaire to mains supply (230 V). Press sensing device gently to turn the luminaire on or off.
- Holding the sensing device enables to adjust the light intensity infinitely.
- Set the desired beam direction by tilting the luminaire.
Cleaning · Maintenance
- Clean luminaire regularly with solvent-free cleansers from dirt.
- We recommend that you dry-clean the sensing device.
Replacing the LED module
-
The designation of the LED module is noted on a label in the luminaire.
-
The light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted. The module can be replaced by qualified persons using standard tools. -
Disconnect the electrical installation.
-
Open the luminaire.
-
Please follow the installation instructions for the LED module.
-
Close the luminaire.
Accessory · Wooden bases
- For this luminaire wooden bases in 3 surfaces are optional available.
- Wooden bases are accessories and must be ordered separately.
- Natural oak 13 209
- Ash black 13 208
- Ash white 13 277
Spares
- Glass/Trim ring 20 000 042 B4
- LED power supply unit DEV-0305/350
- Connecting cable with dimme r 62 001 185
- LED module 3000 K LED-0978/930
- Reflector 75 002 766
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>