AViANCE HD00506 1 Light Bronze Outdoor Installation Guide

AViANCE HD00506 1 Light Bronze Outdoor

Product Specifications

• Model Number : HD00506
• Manufacturer : AVIANCE
• Power Source : Electric
• Material: Glass, Metal
• Colour: Not specified

Product Usage Instructions

Assembling the Fixture

1. Shut off the power at the circuit breaker and remove the old fixture, including the single bar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
3. Attach the mounting screw partway into the side hole of the crook crossbar, then lock it securely with a hex nut until tight. Attach the crossbar to the junction box using two box screws. Ensure the side of the crossbar marked GND faces out. Note that the junction box is not included.
4. Hold the glass carefully and insert it into the bottom frame of the lamp.

Connecting the Wires

1. Connect the electrical wires as follows: Black fixture wire to black house (hot) wire, white fixture wire to white (neutral) house wire. Secure all wire nuts and consider wrapping connections with electrical tape. If your outlet box has ground wires, connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the crossbar.
2. Tuck the wire connections neatly into the wall junction box.

Your installation is now complete. Return power to the junction box and test the fixture.

Thank you for purchasing an AVIANCE product.

Need assistance with parts or assembly? Please email customer service at: info@aviancelighting.net

DOC202404HD00506

• The drawing shown may not exactly match the product enclosed.
• However, the installation instructions do apply to this product.

HD00506

• WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
• ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.

ASSEMBLING THE FIXTURE

1. Shut off the power at the circuit breaker and remove old fixture, including the single bar.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.

3. Attach the mounting screw part way into the side hole of the crook cross bar, then lock it securely with hex nut until becoming. Attach the cross bar to the junction box using two box screws as shown. The side of the cross bar marked “GND” must face out. The junction box is not included.

4. Be very careful, hold the glass(C), insert to the bottom frame of the lamp body(A).
   NOTE : first, the bottom of glass must inset to the frame in the bottom place, fixed the glass with the small sheet iron in the frame.

5. Install the light bulb(Not included) in accordance with the fixture’s specifications.
   NOTE : DO NOT EXCEED THE MAXIMUM WATTAGE RATING!

6. Follow wiring instructions carefully (see fig.2).

7. Attach the back plate of the lamp body(A) onto the junction box, aligning screws on cross bar with mounting holes and lock it securely with the ball nuts(B).

8. With silicone caulking compound, caulk completely around where back of cover meets with the wall surface to prevent water from seeping into junction box.

CONNECTING THE WIRES

1. Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has a ground wires (green or bare copper) connect fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the crossbar.
2. Tuck the wire connections neatly into the wall junction box.

Your installation is now complete. Return power to the junction box and test the fixture.

Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:info@aviancelighting.net

©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.

FAQ

Q: What should I do if I lose a small part during installation?
A: Contact customer service at info@aviancelighting.net for assistance in obtaining a replacement part.

Q: Can this fixture be installed outdoors?
A: This product is designed for indoor use only. Do not install it outdoors.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>