elk HOME 69485-6 Noura Modern Champagne Gold Chandelier Light Installation Guide

elk HOME 69485-6 Noura Modern Champagne Gold Chandelier Light

Product Information

This product is a fixture designed for installation in accordance with the National Electrical Code (NEC) and all local code specifications. It comes with a mounting bracket, junction box screws, a ring, spacers, a bottom trim, a hex wrench, screws, a locking link, a chain, a threaded ring, a canopy, and fixture wires.

Specifications

• Item Number: 69485/6
• Website: elkhome.com

FAQs

• Q: What should I do if any parts are missing?
  • A: If anything is missing, please contact the retailer from which the product was purchased.
• Q: Can I install this fixture myself if I am not familiar with code requirements?
  • A: It is recommended to have the installation done by a certified electrician if you are not familiar with code requirements.
• Q: How can I reach customer support if I have any questions?
  • A: You can call our customer support at 800-613-3261 from Monday to Friday, 8:00 AM to 6:00 PM ET.

Product Usage Instructions

Facility

WARNING: Before installation, disconnect power at the main fuse box.

1. Remove all parts and part packages from the box.
2. Carefully pull house wires down out of the junction box to easily access them for connecting the fixture wires.
3. Place the mounting bracket (A) against the junction box with the screw collar loop (E) pointing down towards the floor. Align each slot in the mounting bracket (A) with each hole in the junction box.
4. Thread one junction box screw (B) into each slot in the mounting bracket (A) and into the holes in the junction box. Tighten the junction box screws (B) to secure the mounting bracket (A) to the junction box. Make sure the house wires are still easily accessible and not pinched between the mounting bracket and ceiling.
5. Rotate the arms until they are evenly spaced apart.

Fixture Assembly

1. Place the ring (P) against the bottom of the fixture body (O). Pass the threaded studs on the bottom of the fixture body through the holes along the inside of the ring (P).
2. Screw one spacer (R) onto the end of each threaded stud0 protruding from the ring (P).
3. Fit the bottom trim (M) inside the ring (P). Pass the holes in the ends of the bottom trim (M) over the threaded studs.
4. Using the hex wrench (N), thread one screw (L) into each hole in the bottom trim (M) and into the spacers (R). Tighten the screws (L) to secure the bottom trim (M) in place. Do not over tighten.
5. Connect one locking link (G) to the loop.
6. Determine the desired hanging height of the fixture and cut the chain (H) to achieve the desired height.
7. Slip the chain link at the end of the chain (H) onto the locking link (G) on the loop.
8. Weave the fixture wires through the chain links, skipping every other chain link.
9. Slip the threaded ring (F) and then the canopy (D) down over the end of the chain (H).

Wire Connections

1. Strip 3/4 of insulation from the ends of the fixture wires.
2. Carefully push the fixture wires up through the hole in the screw collar loop (W) attached to the mounting bracket (A) and out of the end of the threaded pipe inside the junction box. Pull the fixture wires so they are easily accessible to connect to the house wires.
3. To help in connecting the fixture wires to the house wires, temporarily connect the second locking link (G) to the link at the end of the chain (H) and to the screw collar loop (W).
4. Slightly loosen the ground screw on the mounting bracket (A), but do not completely remove it. Wrap the house ground wire (copper) around the ground screw, leaving enough ground wire to attach to the fixture ground wire.
5. Twist the end of the fixture ground wire and the end of the house ground wire together. Twist the wire nut (C) onto the ends of the wires. Completely tighten the wire nut (C). Refer to the chart below for correct wire connections.

Wire Connections Chart

• Connect Supply (House) Ground Copper Wire to:
  • Bare Copper Wire gold
  • Bare Silver Wire gold
  • Green Insulated Wire

WARNING

• DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.
• This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
• Before assembly, remove all parts and part packages from box. If anything is missing, please contact the retailer from which the product was purchased.

Installation Instructions

1. Carefully pull house wires down out of junction box so house wires are easily accessed to connect fixture wires.
2. If screw collar loop (W) is already attached to mounting bracket (A), proceed to Step 3. To assemble screw collar loop (W) to mounting bracket (A): Hold mounting bracket (A) so head of ground screw is pointing down towards floor. Hold threaded pipe so two hexnuts already attached to threaded pipe (E) are pointing down towards floor. From side of mounting bracket with ground screw head, screw short end of threaded pipe (E) into hole in center of mounting bracket (A) until hexnut on threaded pipe (E) touches mounting bracket. Thread hexnut (V) onto end of threaded pipe (E). Tighten hexnut (V) to secure threaded pipe (E) to mounting bracket (A). Thread screw collar loop (W) onto end of threaded pipe pointing down towards floor. Tighten screw collar loop up against hexnut on threaded pipe (E).
3. Place mounting bracket (A) up against junction box. Screw collar loop (E) should be pointing down towards floor. Align each slot in mounting bracket (A) with each hole in junction box.
4. Thread one junction box screw (B) into each slot in mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to junction box.
   • CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between mounting bracket and ceiling.
5. Rotate arms until arms are evenly spaced apart.
6. Place ring (P) up against bottom of fixture body (O). Pass threaded studs on bottom of fixture body through holes along inside of ring (P).
7. Screw one spacer (R) onto end of each threaded stud protruding from ring (P).
8. Fit bottom trim (M) inside ring (P). Pass holes in ends of bottom trim (M) over threaded studs.
9. Using hex wrench (N), thread one screw (L) into each hole in bottom trim (M) and into spacers (R). Tighten screws (L) to secure bottom trim (M) in place. DO NOT over tighten.
10. Connect one locking link (G) to loop.
11. Determine desired hanging height of fixture. Cut chain (H) to length to achieve desired height.
12. Slip chain link at end of chain (H) onto locking link (G) on loop.
13. Weave fixture wires through chain links, skipping every other chain link.

14. Slip threaded ring (F) then canopy (D) down over end of chain (H).
    Connect Supply (House) Ground Copper Wire to:

    Bare Copper Wire or,
    Bare Silver Wire or,
    Green Insulated Wire.

15. Strip 3/4” of insulation from ends of fixture wires.
16. Carefully push fixture wires up through hole in screw collar loop (W) attached to mounting bracket (A) and out end of threaded pipe inside junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
17. To aid in connecting fixture wires to house wires, temporarily connect second locking link (G) to link at end of chain (H) and to screw collar loop (W).
18. Slightly loosen ground screw on mountingbracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of house ground wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart below for correct wire connections.
    Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
    ---|---
    Black Wire or,| White Wire or,
    Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
    No printed words on wire insulation or,| Printed words on wire insulation or,
    Insulated Wire (other than green)

with Copper Conductor.

| Insulated Wire (other than green)

with Silver Conductor.

*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth.

The neutral wire is square in shape or ridged.

19. Twist end of house lead wire (black) and end of fixture lead wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference chart to the right for correct wire connections.
20. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts.
21. Carefully push all wires and wire nuts into junction box.
22. Remove second locking link (G) from last link on chain (H) and screw collar loop (W).
23. Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar loop (W). Position canopy (D) up against ceiling.
24. Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar loop (W). Tighten threaded ring (F) to secure fixture to ceiling.
25. Attach second locking link (G) to link at end of chain (H). Attach locking link (G) at end of chain (H) to loop on screw collar loop (W). 26. Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on socket of fixture.
    • WARNING: DO NOT exceed maximum bulb wattage.

Contact

• ANY QUESTIONS CALL: 800-613-3261
• M-F 8:00AM-6:00PM ET
• elkhome.com

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>