BEGA 50808.1 Studio Line Wall Light LED Instruction Manual

: June 13, 2024
: BEGA

Table of Contents

Dimension
Application
Product description
Safety
Overvoltage protection
Lamp
Setting the colour temperature
Installation
Cleaning · Maintenance
Replacing the LED module
Spares
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 50808.1 Studio Line Wall Light LED

BEGA 50808.1 Studio Line Wall Light LED

Dimension

Application

Wall luminaire · indoor luminaire for the glare free illumination of wall surfaces with the mounting surface being the reflection surface. The light emits upwards and downwards.
Luminaire with adjustable colour temperature (Tunable White), which can be controlled by DALI colour light control (DT8, TW). We recommend the use of BEGA DALI system components.

Product description

Luminaire housing made of aluminium, finish Colour velvet white Synthetic cover with light diffusing structure
Reflector made of pure anodised aluminium 2 elongated fixing holes
Width 5.5mm · 570mm spacing 1 cable entry for through-wiring for mains cable
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V 0/50-60 Hz
DC 176-280 V
DC Start ≥ 190 V
DALI controllable (Device Type 8 for Tunable
White according to IEC 62386-209)
A basic isolation exists between power cable and control line
Safety class I
– Safety mark
– Conformity mark
Weight: 4.0 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve an additional protection against e.g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Lamp

Module connected: wattage 23.2 W
Luminaire connected: wattage 28 W
Rated temperature: ta=25 °C
Ambient temperature: ta max=60 °C

Module designation: 4x LED-1050/9TW
Colour temperature: adjust. 2700-6500 K
Colour rendering index: Ra > 90
Module luminous flux: 3700 lm
Luminaire luminous flux: 3167 lm
Luminaire luminous efficiency: 113,1 lm/W

Setting the colour temperature

The LED colour temperature of the luminaire can be set from 2700 to 6500 K (“Tunable White”). Please note: To be able to set the LED colour temperature, the controller used must support DALI Device Type 8. If no LED colour temperature setting is made, 3000 K will be used by default.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.

Undo the hexagon socket head screws (wrench size 3mm) and lift luminaire top. Loosen earth connection (plug connection) and LED-connection between luminaire top and luminaire base.
Lead the mains supply cable through the cable entry of the luminaire base.
Note position of application “arrow down”. Fix luminaire base with enclosed or any other suitable fixing material onto the mounting surface.
Make earth conductor connection. Push silicone sleeves over the lines and make electrical connection.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light output.
Make earth connection (plug connection) and LED-connection between luminaire top and luminaire base again.
Note position of application of the luminaire “arrow down”.
Install luminaire top part, adjust it and tighten screws evenly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free cleansers from dirt.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Undo one of the two external locking screws
(Torx) in the luminaire housing and remove the lateral housing cover.
Remove the synthetic cover from the profile of the luminaire housing.
Remove the LED module. Install the replacement LED module. Please follow the installation instructions for the LED module.
A defective synthetic cover must be replaced.
Close up the luminaire again in reverse order.