AViANCE HD27169 2 Light Black Dimmable Outdoor Installation Guide
- July 3, 2024
- AVIANCE
Table of Contents
AViANCE HD27169 2 Light Black Dimmable Outdoor
Product Information
- Model: HD27169
- Fixture Type: Ceiling Light Fixture
- Power Source: Electric
- Material: Metal
- Colour: Silver
- Maximum Wattage: Refer to fixture specifications
Product Usage Instructions
Assembling the Fixture:
- Place the candle sleeve over the lamp holder.
- Install the light bulbs (not included) following the fixture specifications.
- Note: Ensure not to exceed the specified wattage for the bulbs.
Hanging the Fixture:
Turn off the power at the circuit breaker and remove the old fixture from the
ceiling.
Connecting the Wires:
- Connect the black wire from the ceiling junction box to the smooth wire leg from the fixture.
- Connect the white/ribbed wires accordingly.
- Connect the bare copper wires (ground).
Your installation is now complete. Restore power to the junction box and test the fixture for functionality.
FAQ:
-
Q: What should I do if the fixture does not turn on after installation?
A: Check the connections of the wires to ensure they are properly secured. Verify that the power source is active. -
Q: Can I use bulbs with wattage higher than specified?
A: No, it is crucial to adhere to the specified wattage to prevent damage to the fixture and ensure safety.
Thank you for choosing AVIANCE. For further assistance with parts or assembly, please contact our customer service at info@aviancelighting.net.
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
WARNING!
SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
ASSEMBLING THE FIXTURE
ASSEMBLING THE FIXTURE (Fig.2)
- Put the candle sleeve over the lamp holder.
- Install the light bulbs(Not included) according to the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE
HANGING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker and remove the old fixture from the line, including the old single bar. Shut off the power at the circuit breaker and remove the old fixture from the ceiling, including the old single bar.
- Carefully unpack the new fixture and lay all the parts on a clear surface.
- Thread nipple (C) into loop (F) until snug.
- Thread the other end of the nipple (C) with a loop attached to a single bar (D) until snug.
- Place lock washer (B) over the end of nipple protruding through single bar and thread hex nut (A) onto nipple until tight.
- Take this single bar assembly and mount it to ceiling junction box with junction box screws (E). Tighten screws securely with screwdriver.
- Use proper chain pliers to open one end link of the chain provided and connect to the fixture loop. Close the link.
- By measuring, determine the correct number of links needed for proper hanging height. Using proper chain pliers disconnect and discard the remaining chain.
- Lace the fixture wires through the chain.
- Slip the loop collar (H) over the chain, then do the same with the canopy (G).
- Open the other end link of the chain and hang the fixture on the loop at the ceiling . Close the link.
- Feed the fixture wires through the loop (F) and nipple (C) and pull until taut.
CONNECTING THE WIRES
CONNECTING THE WIRES (Fig.3)
- Take the black wire from the ceiling junction box and the smooth wire leg from the fixture and twist the bare ends together. Twist the wire connector onto the end of the wire until snug.
- Repeat the same process with white junction box wire and ribbed wire leg of fixture wire. NOTE: Twist wires together in the same direction you twist the wire connector onto wires.
- If your junction box has a grounding wire (green or bare copper), attach this wire and the bare copper wire from the fixture together as in step 1. If the junction box has no ground wire, attach the bare copper fixture wire to the green ground screw on the crossbar.
- Tuck these wire connections neatly into the ceiling outlet box and then raise the canopy (G) to the ceiling. Raise the loop (H) and thread it onto the ceiling loop protruding through the canopy.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:
info@aviancelighting.net.
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>