AViANCE 27212 1 Light Black Outdoor Hardwired Installation Guide
- July 3, 2024
- AVIANCE
Table of Contents
AViANCE 27212 1 Light Black Outdoor Hardwired
Product Specifications:
- Model: HD04184
- Brand: AVIANCE
- Power Source: Electrical
- Colour: Not specified
- Material: Not specified
- Usage: Indoor lighting fixture
Product Usage Instructions
Assembling the Fixture:
- Shut off the power at the circuit breaker and remove the old fixture.
- Unpack the new fixture and lay out all parts in a clear area.
- Attach the mounting screw partway into the side hole of the crook crossbar and secure it with a hex nut.
- Attach the crossbar to the junction box using two box screws, ensuring the side marked GND faces out.
- Hook the lamp body’s loop with the end of the arm(A) and align the end hole.
Connecting the Wires:
- Connect the black fixture wire to the black house (hot) wire, and the white fixture wire to the white (neutral) house wire.
- Secure all wire nuts and optionally wrap connections with electrical tape.
- If there is a ground wire in your outlet box, connect the fixture’s ground wire to it; otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Restore power to the junction box and test the fixture.
Thank you for choosing AVIANCE!
FAQ:
Q: What should I do if I encounter difficulties during installation?
A: For assistance with parts or assembly, please email customer service at
info@aviancelighting.net referencing
DOC202307HD04184.
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the
installation instructions do apply to this product.
WARNING!
SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
ASSEMBLING THE FIXTURE
ASSEMBLING THE FIXTURE (Fig.1)
- Shut off the power at the circuit breaker and remove the old fixture, including the single bar. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
- Attach the mounting screw part way into the side hole of the crook crossbar, then lock it securely with a hex nut until becoming. Attach the crossbar to the junction box using two box screws. The side of the crossbar marked “GND” must face out.
- Follow wiring instructions carefully (see fig.2).
- Using the end of the arm(A) hook the lamp body’s loop, align the end hole of the arm(A) with the top hole of the back plate, and lock it securely with screw(E) and hex nut.
- Attach the back plate of the lamp body(B) onto the junction box, align screws on a crossbar with mounting holes and lock it securely with the ball nuts(C).
- Install the light bulbs(Not included) under the fixture’s specifications. NOTE: DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- With silicone caulking compound, caulk completely around where the back of the cover meets with the wall surface to prevent water from seeping into the junction box.
CONNECTING THE WIRES
CONNECTING THE WIRES (Fig.2)
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has ground wires (green or bare copper) connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at:
info@aviancelighting.net.
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>