BEGA 33507 Wall Luminaire LED Light Ceiling Instruction Manual
- June 21, 2024
- BEGA
Table of Contents
BEGA 33507 Wall Luminaire LED Light Ceiling
Dimension
Instructions for use
Application
Ceiling and wall luminaire with high protection class for a variety of
lighting tasks.
A luminaire made of aluminium alloy and crystal glass.
The colour temperature of the luminaire can be set optionally to 3000K and 4000K.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Crystal glass, white inside
Silicone gasket
2 mounting holes ø 4.8mm
Distance apart 110mm
2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements in
accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect
temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical
impacts < 2 joule
– Safety mark
– Conformity mark
Weight: 1.4 kg
This product contains light sources of energy
efficiency class(es) B
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.
Lamp
Module connected wattage 2.8 W
Luminaire connected wattage 3.9 W
Module designation LED-1512/83040
Colour rendering index CRI >80
Rated temperature ta=25 °C
Ambient temperature ta max=50 °C
Operation at colour temperature 3000 K
Module luminous flux 580 Im
Luminaire luminous flux 266 Im
Luminaire luminous efficiency 68,2 Im/W
Operation at colour temperature 4000 K
Module luminous flux 595 Im
Luminaire luminous flux 272 Im
Luminaire luminous efficiency 69,7 Im/W
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Undo locking screw and turn cover ring as far as it will go. Remove cover ring
and glass from the luminaire base.
Disassemble LED module.
Disconnect plug-connection of the LED connecting cable.
Lead the mains supply cable through the cable entry of the luminaire base.
Note position of application of the luminaire “arrow down”.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the position marked by the red information label immediately before finally closing the luminaire.
The colour temperature of the LED module was set to 3000 K by default (switch position 1: “on”, 2: “off”).
For colour temperature 4000 K, the switch position 1: “off” and 2: “on” must be selected.
Switching may only be carried out when disconnected from the power supply!
Connect the LED connection cable by means of a plug connector.
Assemble LED module.
Tighten the screws evenly. Please observe that the LED board is not damaged
mechanically.
Make sure that gasket is positioned correctly.
Insert glass into the shield frame in such a way that the flattened sides of
the glass are in the region of the casting bars. Then turn glass IN between
the bars.
Place cover ring with glass onto the luminaire base and turn it clockwise as
far as it will go.
Tighten locking screw.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Spares
Spare glass 11 002 974 11
LED power supply unit DEV-0303/350
LED module LED-1512/83040
Gasket 83 001 312
Customers Support
BEGA Gantenbrink-Leuchten KG
Postfach 3160
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>