BEGA 24 179 Ceiling and Wall Luminaire Instruction Manual
- June 20, 2024
- BEGA
Table of Contents
BEGA 24 179 Ceiling and Wall Luminaire Instruction Manual
Instructions for use
Application
Unshielded ceiling and wall luminaire with high protection class.
A luminaire made of die cast aluminium and with an impact resistant synthetic
diffuser. The colour temperature of the luminaire can be set optionally to
3000K and 4000K.
Product description
Luminaire made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Impact-resistant synthetic cover
Silicone gasket
2 mounting holes ø 4.5mm
Distance apart 180mm
2 cable entries for through-wiring of mains
supply cable ø 7-12mm
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements in
accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components Safety
class I
Ball proof – The testing of ball impact safety was carried out
exclusively with handballs in
accordance with DIN 18032-3 : 2018-11. Protection class IP 65
Dust-tight and protection against water jets Impact strength IK10
Protection against mechanical impacts < 20 joule
– Safety mark
– Conformity mark
Weight : 1.2 kg
This product contains light sources of energy efficiency class(es) D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e.g. transients, etc. we recommend
separate overvoltage protection components. You can find them on our website
at www.bega.com.
The ideal protection of all electronic components installed in the luminaires
is achieved by using bounce-free switching contacts such as an electronic
relay (solid-state relay), e.g. BEGA 71320.
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Lamp
Module connected wattage: 7 W
Luminaire connected wattage : 8.1 W
Module designation: LED-1490/83040
Colour rendering index: CRI >80
Rated temperature :ta=25 °C
Ambient temperature : ta max=40 °C
Operation at colour temperature :3000 K
Module luminous flux : 1160 lm
Luminaire luminous flux : 737 lm
Luminaire luminous efficiency : 91 lm/W
Operation at colour temperature: 4000 K
Module luminous flux: 1220 lm
Luminaire luminous flux; 775 lm
Luminaire luminous efficiency :95,7 lm/W
Installation
Undo hexagon socket head screw (wrench size 3mm) through the opening in the
luminaire
housing up to the stop and lift luminaire top.
Disconnect the earth conductor connection from the plug connection.
Disconnect plug-connection of the LED connecting cable.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Tighten screw cable gland.
Make the earth conductor connection and the electrical connection.
In order to guarantee the maximum service life of the electrical components,
the enclosed desiccant pouch must be placed in the luminaire.
Remove the desiccant pouch from the foil packaging and place it in the
position marked by the red information label immediately before finally
closing the luminaire.
The LED module can optionally be operated
with a colour temperature of 3000 K or 4000 K. Check the labelling to ensure a
correct socket match when connecting the plug-in device to the LED connecting
cable.
Switching may only be carried out when disconnected from the power
supply!
Make earth conductor connection between luminaire top and luminaire base.
Push plug into coupler as far as it will go.
In order to ensure the tightness of the luminaire, the grub screw for fixing
the luminaire upper part must not lie in the marked area
Make sure that gasket is positioned correctly. Tighten grub screw firmly.
Cleaning · Maintenance
Clean dirt and debris from the luminaire regularly with a clean, soft, lint-
free cloth that is kept damp throughout the cleaning.
If possible, please use water for this, adding a little commercial dishwashing
detergent.
For lacquered surfaces we recommend the use of BEGA Lacquer Care Set 71 179.
Cleaning agents containing solvents and high pressure cleaners are unsuitable
for cleaning and maintenance
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA
replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced. Close the luminaire.
Spares
Synthetic cover :15 000 574
LED power supply unit :DEV-0304/350
LED module :LED-1490/83040
Gasket Synthetic diffuser: 83 000 557 .1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>