BEGA 51 294.5 Ceiling and Wall Luminaire For Indoor Use Instruction Manual
- June 20, 2024
- BEGA
Table of Contents
51 294.5
Technical amendments reserved
Ceiling and wall luminaire for indoor use
Instructions for use
Application
Ceiling and wall luminaire · Indoor luminaire with synthetic cover, white
interior, for a host of lighting applications.
Ideal for use in corridors, passageways and functional rooms.
Product description
Ceiling and wall luminaire
Luminaire housing made of synthetic material, finish colour velvet black
Transparent synthetic cover, white interior Two elongated mounting holes
Width 4.8 mm · 120 mm spacing 2 cable entries for through-wiring the
connecting cable 7-10.5 mm in diameter, max. 3 G 1.5@
Connection terminal 2.5@
Earth conductor connection
BEGA Ultimate Driver ® Complies with flicker requirements in accordance with
IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-280 V
BEGA Thermal Control ®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
**** – Conformity mark
Weight: 1.0 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Lamp
| Module connected wattage | 6.7 W |
|---|---|
| Luminaire connected wattage | 7.8 W |
| Rated temperature | t = 25 °C |
| Ambient temperature | t a max a = 50 °C |
51 294.5 K3
| Module designation | LED-1284/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 80 |
| Module luminous flux | 1050 lm |
| Luminaire luminous flux | 475 lm |
| Luminaire luminous efficiency | 60,9 lm / W |
Installation
The luminaire must only be operated with the complete protective cover.
LED are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping.
Pick up the luminaire base.
Lead the mains supply cable through the cable entry of the luminaire base.
Fix luminaire base with enclosed or any other suitable fixing material onto
the mounting surface.
Be sure to use the gasket rings supplied.
Make the earth conductor connection and the electrical connection.
Pick up the luminaire top and connect the twopin LED plug connector.
IMPORTANT:
Make sure that the 2-pole LED plug connector is not placed inside the
rectangular LED recess before you join the luminaire base with the luminaire
top. Guide the mounting sockets of the luminaire top exactly onto the
installation bolts of the luminaire base.
Applying even pressure on both sides, lock together the luminaire top and
luminaire base.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by
qualified persons using standard tools.
Disconnect the system from the power supply.
Carefully insert a slotted screwdriver successively into the two flat
openings at the edge of the luminaire top and lift the luminaire top on both
sides away from the luminaire base against the resistance of the locking
mechanism.
Disconnect the two-pin LED plug connector. Please note: To prevent damages or
scratches on the surface, set the luminaire top down with the front side on a
soft base.
Using a slotted screwdriver, exert pressure on the snap-in hook on the inside
of the luminaire top until the LED module releases from the holder.
Remove the LED module. Install the replacement module over the snap-in holder
in the luminaire top.
Please follow the installation instructions for the new LED module.
A defective luminaire cover must be replaced. Pick up the luminaire top and
reconnect the two-pin LED plug connector.
Guide the mounting sockets of the luminaire top exactly onto the installation
bolts of the luminaire base.
Applying even pressure on both sides, lock together the luminaire top and
luminaire base.
Spares
| Locking bolt | 16 006 926 D |
|---|---|
| LED power supply unit | DEV-0451/350 |
| LED module 3000 | LED-1284/930 |
| K Cover + housing | 75 005 752 |
| Gasket | 83 002 289 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
Documents / Resources
| BEGA
51 294.5 Ceiling and Wall Luminaire For Indoor
Use
[pdf] Instruction Manual
51 294.5 Ceiling and Wall Luminaire For Indoor Use, 51 294.5, Ceiling and Wall
Luminaire For Indoor Use, Wall Luminaire For Indoor Use, Luminaire For Indoor
Use, Indoor Use
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>