BEGA 85110 Compact Flood Light Mounting Canopy Instruction Manual

: June 15, 2024
: BEGA

Table of Contents

BEGA 85110 Compact Flood Light Mounting Canopy
Product Usage Instructions
FAQ
Technical amendments reserved
Instructions for use
Safety
Overvoltage protection
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 85110 Compact Flood Light Mounting Canopy

Specifications:

Application: Compact floodlight for permanent installations
Rated Power: 55.5W – 60W
Colour Temperature: 3000K – 4000K
Colour Rendering Index (CRI): >90
Luminous Flux: 5985lm – 6490lm
Luminous Efficiency: 49.5lm/W – 53.7lm/W
Rated Temperature: 25°C – 45°C

Product Usage Instructions

Safety:

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer is not liable for damage due to improper use or installation. Any modifications to the luminaire must be done by authorized personnel.

Overvoltage Protection:

The luminaire’s electronic components are protected against overvoltage as per DIN EN 61547. For additional protection against transients, consider using separate overvoltage protection components available on the manufacturer’s website.

Installation:

Handle LED components with care to avoid direct contact with the light output opening during installation or relamping. Follow the provided sketch to mount the floodlight unit onto the mounting plate securely. Adjust the beam direction as needed by loosening the joint screw, setting the direction, and then tightening the screw with a torque of 7 Nm.

Maintenance:

Regularly inspect the connecting cable between the mounting box and floodlight for damages. Any damaged cables should be replaced by a qualified electrician.

Accessories:

Additional accessories such as shields are available for this product. Separate instructions for their use can be provided upon request.

FAQ

Q: Can I install this floodlight myself?

A: No, installation and commissioning must be done by a qualified electrician to ensure safety and proper functioning.

Q: What should I do if I notice damage to the connecting cable?

A: Any visible damage to the connecting cable should be addressed by a qualified electrician for replacement.

Technical amendments reserved

Compact downlight with minimal diffuse light percentage

Instructions for use

Application

Compact floodlight with mounting box for permanent installations on a wall, under a ceiling or on a pillar.
BEGA Ultradark Optics® offer a maximum of illumination and eye comfort due to a minimised diffuse light percentage and highly efficient glare suppression.

Product description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite or silver
Matt safety glass
Internal louvres and polymer lens
BEGA Ultradark Optics®
Louvres and interior surface of anti-glare ring with maximum light-absorbing ultra-black nano-coating
Rotation range of floodlight 350°
Swivel range -20°/+90°
Mounting box with 2 fixing holes
ø 6 mm · 85 mm spacing
2 cable entries for through-wiring of mains
supply cable ø 7-10.5 mm, max. 5 G 1.5@
Connecting terminal 2.5@
with plug connection
Earth conductor connection
BEGA Ultimate Driver®
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V x 0/50-60 Hz
DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK07
Protection against mechanical
impacts < 2 joule
Conformity mark
Wind catching area: 0.058 m²
Weight: 5.2 kg
This product contains light sources of energy efficiency class(es) F

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to
the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Please note:
Contact with the inner surface of the luminaire reflector should be avoided in order to permanently protect the special stray light-minimising properties of the nano-coating.

Installation

LED are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo hexagon socket head screws (wrench size 3 mm) at the mounting box and remove mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied. Make earth conductor connection.
Push silicone sleeves over the lines and make electrical connection to terminal (plug connection).
For digital control please use the 2-pole plug connector DA, DA.
In case this connector is not used the luminaire will be operated at full light output.
Push plug into coupler as far as it will go. Make sure that gasket is positioned correctly.
Place floodlight unit onto the mounting plate as displayed in the sketch, align and screw together firmly.

Adjustment of beam direction:
Undo joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7 Nm.

Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.

Lamp

Module connected wattage 55.5 W
Luminaire connected wattage 60 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 45 °C

85 110 K3

Module designation LED-1263/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 5985 lm
Luminaire luminous flux 2971 lm
Luminaire luminous efficiency 49,5 lm / W

85 110 K4

Module designation LED-1263/940
Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 6490 lm
Luminaire luminous flux 3222 lm
Luminaire luminous efficiency 53,7 lm / W

Lighting technology
Symmetrically focused broad spread
light distribution with minimal diffuse light percentage.
Half beam angle 56°

Maintenance
The connecting cable between mounting box and floodlight has to be inspected regarding obvious damages and has to be replaced by a qualified electrician only.

Replacing the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by a qualified person using commercially available tools.
Disconnect the system from the power supply. Open the floodlight:
Loosen the back locking pin (hexagon socket wrench size 2) in the trim ring.
Remove the trim ring along with the safety glass and reflector by twisting it anti-clockwise.

Please note:

Contact with the inner surfaces of the louvres and luminaire reflector should be avoided in order to permanently protect the special stray light-minimising properties of the nano-coating. Grasp the louvres from the outside and lift them out. Loosen the three mounting screws (Torx drive T20) and lift the lens holder (with the loosely inserted lenses) upward horizontally out of the housing.
Replace LED module.
Please follow the installation instructions for the LED module.
Install in reverse order.
When installing the lens holder, make sure that the LED connecting cable is not pinched. Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Place the trim ring with glass and reflector on the floodlight housing so that the notches in the trim ring and luminaire housing sit on top of each other.
Twist on the trim ring clockwise as far as the stop. Screw in the locking pin.

Accessories

71 282 Shield
71 287 Cylindrical shield
For the accessories a separate instructions for use can be provided upon request.

Spares