BEGA 23 256.6 Wall Luminaire Instruction Manual

Table of Contents

Product Specifications

Safety Information

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should perform the installation and commissioning.
The manufacturer is not liable for damage resulting from improper use or installation.

Overvoltage Protection

The electronic components in the luminaire are protected against overvoltage as per DIN EN 61547.
For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.

Facility

When mounting or dismantling, maintain a minimum distance of 350 mm between the removable cap and the wall.

Spare Parts

Available spare parts include spare glass, an LED power supply unit, LED modules in both 3000 K and 4000 K, and a gasket. Refer to the provided part numbers for ordering.

Q: Can I install the luminaire myself?

A: No, only a qualified electrician should carry out the installation and commissioning to ensure safety and proper operation.

Q: Where can I find additional protection components against overvoltage?

A: Additional protection components can be found on the manufacturer’s website at www.bega.com.

Application

Wall luminaire · indoor luminaire made of hand-blown opal glass and metal housing, for all lighting tasks in interior applications.
They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with a high protection class.

Luminaire made of Aluminium, finish Colour velvet copper
Hand-blown opal glass
Two elongated mounting holes
Width 6 mm · 460 mm spacing
Insulating housing with cable entry for mains supply cable up to ø 10,5 mm, max. 3 x 1,5@
Connection terminal 2.5@
Earth conductor connection
Complies with flicker requirements by IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 44
Protected against granular foreign bodies ≥ 1 mm and splash water
Impact strength IK02
Protection against mechanical impacts < 0.2 joule
Conformity mark
Weight: 2.2 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage under DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Lamp

23 256.6 K3

23 256.6 K4

Insulation housing

For mounting and dismantling please keep a minimum distance of 350 mm between the removable cap and the wall.
LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.

Open luminaire:

Loosen the knob, remove cap and glass.
Drill mounting holes into the mounting surface – spacing 460 mm.
For the mains supply connecting open the insulation housing – pull open – strip mains supply cable max. 15 mm and lead it into the insulation housing – see sketch.
Make earth conductor connection and electrical connection.
Connect both parts of the insulation housing until they audibly engage.
The outer coating of the cable has to be fully enclosed by the compression nipple.
Fix the luminaire with enclosed or any other suitable fixing material onto the mounting surface.
Place glass into luminaire housing, close the luminaire with the cap and screw in the knob into the cap.

Replacement of the LED module

The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
Disconnect the system.
Loosen lateral knob, remove cap and take out glass.
Please follow the installation instructions for the LED module.
Defective glass must be replaced.
Insert glass into luminaire housing, close luminaire with the cap and screw in knob into the cap.

Spares