84 850 Surface Floodlight BEGA UniLink Instruction Manual

: June 11, 2024
: BEGA

Table of Contents

84 850 Surface Floodlight BEGA UniLink
Specifications
Product Usage Instructions
FAQ
Dimension
Instructions for use
Product Description
Installation
Cleaning Maintenance
Accessories
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

84 850 Surface Floodlight BEGA UniLink

Specifications

Power consumption of 84 850: 0.1 A
Lamp Module connected wattage: 9.7 W
Luminaire connected wattage: 11.9 W
Rated temperature: 25 to 40 degrees Celsius
Ambient temperature: ta
LED-0775/930: Colour Temperature 3000 K, CRI > 90, Luminous Flux 1565 lm, Luminaire Luminous Flux 1138 lm, Luminaire Luminous Efficiency 95.6 lm/W
LED-0775/940: Colour Temperature 4000 K, CRI > 90, Luminous Flux 1655 lm, Luminaire Luminous Flux 1184 lm, Luminaire Luminous Efficiency 99.5 lm/W

Product Usage Instructions

The installation and operation of this luminaire must comply with national safety regulations. The manufacturer is not liable for damage resulting from improper use or installation. Any modifications made to the luminaire make the modifier responsible for it.

Unscrew the hexagon socket screws with a wrench size of 3 mm on the sides of the connection adapter.
Screw the corresponding accessory to the floodlight ensuring a torque of 5 Nm.
Plug the floodlight’s connecting cable into the plug contact of the connecting cable with the country-specific mains plug or distribution box/extension cable.
Ensure the connecting cable of each luminaire in the system does not exceed a length of 50 m from the entry point.
Adjust beam direction by undoing the joint screw with a hexagon socket head wrench size of 5 mm, set desired beam direction, and tighten the joint screw to a torque of 7 Nm.

FAQ

Q: Where can I find additional overvoltage protection components?
A: Additional overvoltage protection components can be found on the manufacturer’s website at www.bega.com.

Dimension

84-850-Surface-Floodlight-BEGA-UniLink-FIG-1

Instructions for use

Application

Surface floodlight BEGA UniLink® with connection adapter for use in combination with various accessories, e.g. for mounting on trees, pipes or wooden structures.
A separate mains plug must be ordered to connect the floodlight to the mains.
The various country-specific mains plug with 0.5 m connecting cable, as well as extension cables and five-way distribution boxes are available as accessories.

Product Description

Floodlight made of aluminium alloy, aluminium and stainless steel
BEGA Unidure® coating technology
Safety glass with optical structure
Silicone gasket
Reflector made of pure anodised aluminium
Rotation range of floodlight is 360° Swivel range -35°/+90° 5 m mains supply cable
X05RN-F FEP 2 × 1@ + 1G2,5@ with
BEGA UniLink® plug-in connector
Complies with flicker requirements under IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V 0/50-60 Hz
DC 170-280 V
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical impacts < 2 joule
– Conformity mark
Weight: 1.7 kg
This product contains light sources of energy efficiency class(es) D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Total load

When configuring your lighting system, please ensure that the maximum power consumption of 6 A is not exceeded.
Information on power consumption can be found in the instructions for use and data sheets for all BEGA UniLink® luminaires.
Power consumption of 84 850: 0,1 A

Lamp

Module connected wattage 9.7 W
Luminaire connected wattage 11.9 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

84 850 K3

Module designation LED-0775/930
Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1565 lm
Luminaire luminous flux 1138 lm
Luminaire luminous efficiency 95,6 lm / W

84 850 K4

Module designation LED-0775/940
Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 1655 lm
Luminaire luminous flux 1184 lm
Luminaire luminous efficiency 99,5 lm / W

Light technique

Broad-spread light distribution.
Half beam angle 80/90°

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage under DIN EN 61547.
To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.

Caution
The BEGA UniLink® plug connectors may only be connected and disconnected in a voltage-free state.

Installation

Unscrew the hexagon socket screws (wrench size 3 mm) on the sides of the connection adapter and screw the corresponding accessory to the floodlight.
Torque = 5 Nm.

Plug the floodlight’s connecting cable into the plug contact of the connecting cable with the country-specific mains plug or into the distribution box or extension cable.
To ensure a sufficiently low protective conductor resistance (loop resistance), the connecting cable of each luminaire in the system must not exceed a length of 50 m from the entry point.

Adjustment of beam direction:
Undo the joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7 Nm.

Please note

Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high-pressure cleaners.

Maintenance
The connecting cable must be checked for external damage and may only be replaced by a qualified electrician.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.