BEGA 51 259.4 Wall Luminaire For Indoor Use Instruction Manual
- June 11, 2024
- BEGA
Table of Contents
BEGA 51 259.4 Wall Luminaire For Indoor Use
DIMENSION
Specifications
- Lamp Module connected wattage: 21.2 W
- Luminaire connected wattage: 24.8 W
- Rated temperature: 25 – 55°C
- Ambient temperature: max 55°C
- Module designation: LED-1320/930
- Colour temperature: 3000 K
- Colour rendering index (CRI ): > 90
- Module luminous flux: 3300 lm
- Luminaire luminous flux: 1651 lm
- Luminaire luminous efficiency: 66.6 lm/W
Instructions for use
Application
Wall luminaire · indoor luminaire with light emission on one side for the
glare-free illumination of wall surfaces with the mounting surface being the
reflection surface.
A luminaire that allows interesting illumination concepts individually or in
rows.
Product Description
- Luminaire housing made of aluminium,
- finish Colour velvet brass
- Silicone light diffuser
- 3 elongated fixing holes
- Width 4.5 mm · 540 mm spacing
- Mounting plate with several openings for cable entry and through-wiring for mains cable Connecting terminals 2.5
- Earth conductor connection
- Complies with flicker requirements by IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1
- LED power supply unit
- 220-240 V 0/50-60 Hz
- DC 176-264 V
- DALI-controllable
- Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Impact strength IK08
- Protection against mechanical
- impacts < 5 joule
- CE– Conformity mark
- Weight: 3.1 kg
- This product contains light sources of energy efficiency class(es) D
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
Overvoltage protection
- The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
- To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
- You can find them on our website at: www.bega.com.
SPECIFICATION
Lamp
- Module connected wattage 21.2 W
- Luminaire connected wattage 24.8 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 55 °C
51 259.4 K3
- Module designation LED-1320/930
- Colour temperature 3000 K
- Colour rendering index CRI > 90
- Module luminous flux 3300 lm
- Luminaire luminous flux 1651 lm
- Luminaire luminous efficiency 66,6 lm / W
Installation
LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation or relamping. Undo the hexagon socket head screws (wrench size 3 mm) and lift the luminaire housing. Loosen earth connection (plug connection) between luminaire housing and mounting plate. Pass the power connecting cable through one of the openings of the mounting plate. Ensure correct directionality towards the area to be illuminated.
- Fasten the mounting plate with the supplied fastening material or other suitable fastening material to the installation surface.
- Make the electrical connection to the terminals. Please ensure the correct wire assignment for the connecting cable.
- Connect the earth conductor to the green-yellow wire ( ). Connect the live conductor to the brown wire (L) and the neutral conductor to the blue wire (N).
- Use the terminals marked DA, DA for digital control.
- If these terminals are not used, the luminaire will operate at full light output.
- Make an earth connection (plug connection) between the luminaire housing and mounting plate again.
- Hang the luminaire housing in the mounting plate and screw it in place with the hexagon socket head screws.
Cleaning · Maintenance
- Clean the luminaire regularly with solvent-free cleansers from dirt.
Replacing the LED module
- The designation of the LED module is noted on a label in the luminaire.
- The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools.
- Disconnect the system and open the luminaire. Please follow the installation instructions for the LED module.
- The defective luminaire cover must be replaced. Close the luminaire.
Spares
LED power supply unit
- DEV-0388/700i
- LED-1320/930
MORE INFORMATION
- BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com
- www.bega.com
- LED module 3000 K with diffusor
FAQ
- Q: Can I replace the LED module myself?
- A: The LED module can be replaced by qualified persons using standard tools. Please follow the installation instructions provided for the LED module.
- Q: Where can I find overvoltage protection components?
- A: Additional overvoltage protection components can be found on the manufacturer’s website at www.bega.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>