Beldray 700 W Handy Plug-In Heater Instruction Manual
- June 7, 2024
- Beldray
Table of Contents
Our warm portable & convenient plug-in heater
700 W HANDY
Plug-In Heater
Instruction Manual
**This product is only suitable for well insulated spaces or occasional use.
Please read all of the instructions carefully and retain for future reference.
Safety Instructions
When using electrical products, basic safety precautions should always be
followed.
Check that the voltage indicated on the rating plate corresponds with that of
the local network before connecting
Always unplug the product and allow to cool fully after use and before any
cleaning or maintenance.
Normal voltage is still present in this product as long as the product is
connected to the electrical source.
This product contains no user-serviceable parts. If the plug or any part of
the product is malfunctioning or if it has been dropped or damaged, only a
qualified electrician should carry out repairs. Improper repairs may place the
user at risk of harm.
Keep the product out of the reach of children and away from heat, sharp edges,
and other heat-emitting products that could cause damage.
Keep furniture, curtains, and other flammable material at least 1 meter away
from the product.
Do not run the supply cord under carpets, rugs etc., or anywhere where it may
present a trip hazard.
Do not immerse the product or plug in water or any other liquid. Do not
operate the product with wet hands.
Do not use this product in the immediate surroundings of a bath, a shower or
swimming pool.
Do not leave the product unattended whilst connected to the mains power supply
or when in use.ting the product to the mains power supply.
Children younger than 3 years old should be kept away from the product unless
continuously supervised.
Children aged from 3 years and less than 8 years should not plug in, regulate
or clean the product or perform user maintenance.
Children aged from 8 years and people with reduced physical, sensory or mental
capabilities or lack of experience and knowledge can use this appliance, only
if it has been placed in its intended operating position and they have been
given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved.
Children should not perform cleaning or user maintenance unless they are older
than 8 years and supervised.
This is not a toy – children should be supervised to ensure they do not play
with the product.
To remove from the mains power supply switch off and remove the plug by hand.
Do not use this product for extended periods of time.
Do not leave the product plugged in or operating overnight. Do not use the
product for anything other than its intended use.
Do not block the air intake of the product; place in an open, well-ventilated
space.
Do not use this product outdoors.
Do not attempt to move the product whilst it is in use.
Do not put objects into any of the openings.
Do not use the product with a programmer, timer, separate remote-control
system or any other device that will switch the product on automatically other
than that supplied with the product, as there is a risk of fire if the heater
is covered or positioned incorrectly.
Do not clean the product with abrasive chemicals or materials such as scourers
as they may damage the product and impair future function. This includes
insecticide and chemical solvents. The product should be used on a stable,
heat-resistant surface. The product must not be located immediately below or
next to a mains power supply. Use single plug sockets only.
Never use accessories that are not recommended or supplied by the
manufacturer. It could cause danger to the user and damage to the product.
Use of an extension cord with the product is not recommended. This product is
intended for domestic use only. It should not be used for commercial purposes.
Caution: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
Hot surface – do not touch the hot section or heating components of the product.
Warning: In order to avoid overheating, do not cover the product.
Always check the plug sockets for damage before and after use. Do not use the product in damaged or ill-fitting plug sockets.
Do not use this product in small rooms whilst occupied by persons incapable of leaving the room on their own, unless constant supervision is provided.
Thermal Cut-out Device
The plug-in heater is fitted with a thermal safety cut-out device, built in to prevent it from overheating. Should the plug-in heater start to overheat, the thermal safety cut-out system will automatically operate and the heat settings will switch off. If this happens:
STEP 1: Switch off the plug-in heater by pressing the on/off switch.
STEP 2: Allow the plug-in heater to cool before removing it from the plug
socket.
STEP 3: Check that the plug-in heater is unplugged from the mains power
supply and allow it to cool for approx. 15 minutes.
STEP 4: Clear any blockages present on the vent, being careful not to
damage the plug-in heater.
STEP 5: Plugin and switch on the plug-in heater at the mains power
supply.
Caution: In order to avoid a hazard, due to inadvertent resetting of the thermal cut-out, the plug-in heater must not be supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility.
**Care and Maintenance
**
Always unplug the plug-in heater from the mains power supply and allow it to
cool sufficiently before performing any cleaning or maintenance.
Wipe the exterior of the plug-in heater with a soft, damp cloth and allow to
dry thoroughly.
Do not use harsh or abrasive cleaning solvents or scourers, as these may
damage the finish of the plug-in heater.
Do not immerse the plug-in heater in water or any other liquid.
Getting Started
Remove the plug-in heater from the box.
Remove any packaging from the plug-in heater.
Place packaging inside the box and either store or dispose of it safely.
In the Box
700 W Handy Plug-in Heater Instruction manual
Features
700 W Power
High-quality LED display
Automatic cool-down function
Ceramic heating element
90 ° swivel plug
2 fan speeds
12-hour timer
Adjustable thermostat between 15-30 ° Thermal cut-out device
Cool-touch case
Description of parts
| 1. | 700 W Handy Plug-in Heater main unit | 7. | Power button |
|---|---|---|---|
| 2. | On/Off switch | 8. | Timer button |
| 3. | Control panel | 9. | Plug rotation button |
| 4. | Increase temperature button (+) | 10. | Vent |
| 5. | Decrease temperature button (-) | 11. | Air intake |
| 6. | LED display | 12. | Finger hold |
Instructions for Use Before First Use
STEP 1: Check that there is no damage to the plug-in heater.
STEP 2: Plug the plug-in heater into a compatible socket at least 1 metre
away from furniture, curtains, or any other flammable materials. Do not block
the air intake on the back of the plug-in heater.
Note: When using the plug-in heater for the first time, a slight odor may be emitted. This is normal and will soon subside. Allow for sufficient ventilation around the plug-in heater. Check the wall socket for damage before and after use.
Using the 700 W Handy Plug-in Heater
STEP 1: Plugin and switch on the plug-in heater at the mains power
supply.
STEP 2: To turn on the plug-in heater, press the on/off switch to the
‘on’ (I) position and press ( ).
STEP 3: Press ‘+’ to increase the temperature output; press ‘-‘ to
decrease the temperature output. The temperature can be set between 15 °C and
30 °C.
STEP 4: To increase or decrease the fan speed, press ‘+’ and ‘-‘ at the
same time. Press both buttons together once for a low-speed setting; the LED
display will show ‘LL’. Press both buttons together again for a high-speed
setting; the LED display will show ‘HH’.
STEP 5: Activate the timer setting by pressing ( ); the display will
change from ‘°C’ to ‘HOURS’. Press ( ) until the desired number of hours has
been selected; 12 hours is the maximum selection.
TIMER OFF – If the timer function is set when the plug-in heater is
switched on, the number of hours is set to when the heater will turn off.
TIMER ON – If the timer function is set when the plug-in heater is
switched off or on standby, the number of hours is set to when the heater will
turn on.
STEP 6: To switch off the plug-in heater, press CO). The fan will
cool for approx. 60 seconds before switching off. Press the on/off switch
to the ‘off(0) position and wait for the plug-in heater to cool fully before
unplugging
Note: The plug-in heater will only produce heat if the set temperature is
higher than the room temperature.
Warning: Never leave the plug-in heater connected to the mains power
supply whilst not in use.
Always use the finger hold to support the heater when pressing the buttons on the control panel. This minimizes the force on the plug socket and reduced the risk of injury.
Rotating the Plug
STEP 1: Press and hold the plug rotation button on the back of the plug-
in heater.
STEP 2: For a horizontal heater position, rotate the plug 90 ° clockwise
whilst holding the plug rotation button.
STEP 3: For a vertical heater position, rotate the plug 90 °
counterclockwise whilst holding the plug rotation button.
Warning: Only attempt to rotate the plug if the plug-in heater is cool
and unplugged.
**Troubleshooting
**
| Problem | Cause | Solution |
|---|---|---|
| The plug-in heater is not operating. The fan is not running. | The plug-in |
heater is not plugged in and switched on at the mains power supply.
The thermal cut-out device has been activated.
| Check that the plug-in heater is plugged in and switched on at the mains power supply.
Switch off and unplug the plug-in heater from the mains power supply and allow it to cool for approx. 15 minutes.
Plugin and switch on the plug-in heater at the mains power supply before trying again.
The fuse has blown.| Unplug the plug-in heater from the mains power
supply and replace the fuse with one that is the same amp rating.
No heat or display light is being emitted from the plug-in heater| There may
be a problem with the power supply to the plug-in heater.| Check the mains
power supply by plugging in a working appliance.
| Item | Symbol | Value | Unit | Item | Unit |
|---|---|---|---|---|---|
| Heat Output | Type of heat input for electric storage local space heaters only |
(select one).
Nominal heat output| p
nom| | kW| Manual heat charge control, with integrated thermostat.|
Nominal
heat output (indicative)| p
mln| | kW| Manual heat charge control with room and/or outdoor temperature
feedback.|
Maximum continuous heat output| p
max•c| | kW| Electronic heat charge control with room and/or outdoor
temperature feedback.|
Auxiliary electricity consumption| Fan-assisted heat output.|
At nominal heat output| el
Tax| | kW| Type of heat output/room temperature control (select one).
At minimum heat output| el
min| | kW| Single-stage heat output and n room temperature control.|
In standby mode| else| | kW| Two or more manual stages, no room temperature
control.|
| | | | With mechanic thermostat room temperature control.|
| | | | With electronic room temperature.|
| | | | Electronic room temperature control plus day timer.|
| | | | Electronic room temperature control plus week timer.|
| | | | Other control options (multiple selections possible).
| | | | Room temperature control, with presence detection.|
| | | | Room temperature control, with open window detection.|
| | | | With distance control option.|
| | | | With adaptive start control.|
| | | | With working time limitation.|
| | | | With black bulb sensor.|
Connection to the mains
Please check that the voltage indicated on the product corresponds with your supply voltage.
Important
As the colors in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, please proceed as follows:
The wires in the mains lead are colored in accordance with the following code:
Blue Neutral (N) Brown Live (L)
FOR UK USE ONLY – Plug fitting details (where applicable).
The wire colored BLUE is the NEUTRAL and must be connected to the terminal
marked N or colored BLACK.
The wire colored BROWN is the LIVE wire and must be connected to the terminal
marked L or colored RED.
On no account must either the BROWN or the BLUE wire be connected to theEARTH
terminal ( )
Always ensure that the cord grip is fastened correctly.
The plug must be fitted with a fuse of the same rating already fitted and
conforming to BS 1362 and be ASIA approved.
If in doubt consult a qualified electrician who will be pleased to do this for
you.
Non-rewireable mains plug
If your appliance is supplied with a non-rewireable plug fitted to the mains
lead and should the fuse need replacing, you must use an ASTA-approved one
(conforming to BS 1362 of the same rating).
If in doubt, consult a qualified electrician who will be pleased to do this
for you.
If you need to remove the plug – DISCONNECT IT FROM THE MAINS and then cut it
off the mains lead and immediately dispose of it safely. Never attempt to
reuse the plug or insert it into a socket outlet as there is a danger of an
electric shock.
UP Global Sourcing UK Ltd.,
Victoria Street, Manchester OL9 ODD. UK.
If this product does not reach you in an acceptable condition please contact
our Customer Services Department by one of the following methods:
Telephone: +44 (0)333 577 9820
Telephone lines are open Monday-Friday, 9 am-5 pm (Closed Bank Holidays)
Email:customersupport@beldray.com
Fax: 0161 628 2126
Please have your delivery note to hand as details from it will be required.
If you wish to return this product please return it to the retailer from where
it was purchased with your receipt (subject to their terms and conditions).
Guarantee
All products purchased as new carry a manufacturer’s guarantee; the time period of the guarantee will vary dependent upon the product. Where reasonable proof of purchase can be provided, Beldray will provide a standard 12-month guarantee with the retailer from the date of purchase. This is only applicable when products have been used as instructed for their intended, domestic use. Any misuse or dismantling of products will invalidate any guarantee.
Under the guarantee, we undertake to repair or replace free of any charge any
parts found to be defective. In the event that we cannot provide an exact
replacement, a similar product will be offered or the cost refunded. Any
damages from daily wear and tear are not covered by this guarantee, nor are
consumables such as plugs, fuses, etc.
Please note that the above terms and conditions may be updated from time to
time and we, therefore, recommend that you check these each time you revisit
the website.
Nothing in this guarantee or in the instructions relating to this product
excludes, restricts or otherwise affects your statutory rights.
The crossed-out wheelie bin symbol on this item indicates that this appliance
needs to be disposed of in an environmentally friendly way when it becomes of
no further use or has worn out. Contact your local authority for details of
where to take the item for recycling.
To be eligible for the extended guarantee, go to www.beldray.com and register your product within 30 days of purchase.
Find us on
www.facebook.com/Beldray
Manufactured by:
UP Global Sourcing UK Ltd.,
Victoria Street, Manchester OL9 ODD. UK
+44 (0)333 577 9820
customersupport@beldray.com ©Beldray
Trademark. All rights reserved.
Please retain instructions for future reference.
Made in China.
CD300719/M0000000N1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>