beper VE.150 Retro Stand Fan Instruction Manual
- June 3, 2024
- beper
Table of Contents
VE.150 Retro Stand Fan
Instruction Manual
For further information and/or for instructions for use in other languages ,
please visit: beper.com
Cod.:VE.150
VE.150 Retro Stand Fan
Retro Stand Fan Use Instructions
Precautions
Read the following instructions carefully, since they give you useful
safety information about installation, use and maintenance and help you avoid
mishaps and possible accidents.
Remove the packing and make sure that the appliance is intact, with special
attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not have to be
accessible to the children, in order to preserve them from danger sources. It
is recommended not to throw these packing material in the domestic waste, but
to deliver them to the appropriate station of collection or destruction
refusals, asking eventually information to the manager of the Sanitation
Department of your own municipality.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds
to the data specified on the label.
The appliance can be damaged if the voltage is not correct. If the plug does
not suit the socket, let it be replaced with another suitable plug by
qualified personnel only, which shall also ensure that the section of the
socket cables is suitable for your appliance power absorption.
Generally, the use adaptors multiple plugs and/or extensions is not
recommended; should they be necessary, please use only simple or multiple
adaptors and extensions in compliance with the safety rules in force, making
sure that the capacity absorption limit marked on the simple adaptors and the
extensions and the maximum power limit marked on the multiple adaptor are not
exceeded.
Do not use the appliance if the cable or the plug shows any damages. Do not
use the appliance after a possible irregular working.
In this case, switch it off and do not break it open. Refer to an authorized
Beper after-sale service for repair and require original spare parts only.
Failing to follow these instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is
to be considered as improper and thus dangerous. The manufacturer cannot be
responsible for any damages deriving from improper, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of
the appliance into water or other fluids. Do not use the appliance near
explosives, highly flammable materials, gases or burning flames.
Do not allow children, disabled people or every people without experience or
technical ability to use the appliance if they are not properly watched over.
Close supervision is necessary when any appliance used by or near children.
Some warnings
Do not plug the supply cord before assembly every parts of the fan. Before
using, check the integrity of the supply cord and eventually remove possible
nodes. Place the fan on a flat and stable surface in a dry place. Keep away to
a reasonable distance the fan from walls, doors, windows or every object that
could avoid the appliance to work in the correct way. Do not cover the body or
grid of the fan when the appliance is working.
Do not plug objects into the grid or inside the appliance.
Do not pull on the supply cord to unplug the appliance.
After using the fan, unplug the cord supply.
If the fan must be stored for a long period or non-used, replace the fan in
the original packaging in a dry place. For every next use, check that the fan
is clean and that the blades turn in the correct way (motor off).
Product and accessories Fig.A
1 - Front guard
2 - Fan blades
3 - Fan blades screw
4 - Fixation screw
5 – Rear guard
6 Motor shaft
7 - Speed control
8 - Fan motor
9 - Power cord| 10 - Knob
11 – Inner tube
12 - Height adjustment Screw
13 - Outer tube
14 - Base
15-Wheight
16 - Fastener
17- Locking screw
---|---
Fan assembly Fig.B
Attaching the telescopic stand to the stand base. First unscrew the l-shaped
screw and remove it and the clamping washer from the bottom of the telescopic
stand.
Turn over the stand base. Place the weighted base centre in its place on the
underside of the base and the clamping washer in the centre of the weighted
base.
Thread the l-shaped screw through the assembly and into the thread in the
telescopic stand.
Tighten firmly, but do not overtighten. Loosen the height adjustment knob and
pull he inner tube out the telescopic stand to the desired height, then
retighten the knob. Attaching the motor housing to the top of the telescopic
stand.
First remove the pivot knob and the bolt from the top of the telescopic stand,
then remove the neck retaining screw and small adjustment knob from the motor
housing bracket. Place the motor housing on the top of the stand and thread
the large pivot bolt through the bracket. Screw in the small retaining screw
and tighten, but do not overtighten.
Fit the large pivot knob onto the end of the bolt and the small adjustment
knob at the other side above the bolt. Tighten the knobs while holding the fan
motor upright. Attaching the guards and fan blade First remove any protective
sleeve from the motor shaft and the four rear guard retaining screws from the
motor housing. Attach the rear guard to the motor housing using the four
screws you just removed. Ensure the handle is at the top. Place the fan blade
over the motor shaft and tighten the fan blade retaining screw, ensuring that
it tightens against the flat part on the motor shaft. Remove the front guard
screw and nut from the front guard and turn the guard retaining clips around
the outside edge outwards.
Hang the front guard by its hook over the top of the rear guard. Bring the
front guard down to meet the rear guard and push the clips inwards until the
front guard is fastened to the rear guard. Finally fit the guard screw through
the holes in the bottom edge of the guard and tighten with the nut.
Speed selection
Choose the speed desired pressing on the buttons of the control panels.
Position 0 the fan switch off.
Position 1 low speed.
Position 2 medium speed.
Position 3 high speed.
Head inclination
It is possible to choose various positions and change the air flow swing.
Before changing it, switch off the fan. Take the motor body, unscrew the
regulation axis and change the inclination of the fan as desired and screw the
air strongly.
Do not try to force the inclination position in order to avoid any failure.
Swing
It is possible to activate or disconnect the swing of the fan, by touching the
swing axis (8). Swing allow to provide the air uniformly.
To activate the push the swig axis (8) down until completely blocked ; the
head fan turns automatically from right to left. To disconnect the swing raise
completely the axis (8).
Cleaning
Before cleaning, switch off and unplug the fan. For cleaning use a soft cloth, that may be softly wet. Do not use alcohol or chemical substances, or any detergent that could damaged this appliance. Do not flush water or other liquids on the fan in order to protect it. After cleaning, dry every parts before using the appliance. During the winter and when not used, keep this appliance in a dry and clean place.
Technical data
Power : 50W
Power supply. 230V~ 50Hz
For any improvement reasons, Beper reserves the right to modify or improve
the product without any notice.
The European directive 2011/65/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.
GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original
purchase a 24 month guarantee applies to material and production defects. The
purchase receipt and the guarantee certificate must be submitted together in
case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase
(fiscal receipt) indicating the date of purchase and the model of the
appliance
For any technical assistance, please contact directly the seller or our head
office in order to preserve the appliance’s efficiency and NOT TO void the
guarantee. Any intervention on this appliance by non-authorized persons will
automatically void the guarantee.
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or
production during the period of guarantee, we guarantee repair free of charge
on condition that:
– The appliance has been used properly and for the purpose for which it has
been intended.
– The appliance has not been tampered with, otherwise it is not maintainable.
– The purchase receipt shall be presented.
– The appliance showing a fair wear and tear shall not be covered by this
guarantee.
Therefore, any part that could be accidentally broken or having visible signs
of use in consumable products (such as lamps, batteries, heating elements…)
the aesthetic parts are excluded from the guarantee, and any defect whatsoever
resulting from non-respect of the rules for use, negligence in usage and/or
maintenance of the appliance, carelessness, wrong or improper installation,
damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the
appliance will be replaced free of charge. In any case, if the part to be
replaced for defect, breakage or malfunction is an accessory and/or a
detachable part of the product, Beper reserves the right to replace only the
very part in question and not the entire product
Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward
your enquiries to your distributor.
Beper. E-mail assistenza@beper.com
Koji e proslediti vase upite vasem distributeru.
BEPER SRL
Via Salieri, 30 – 37050 – Vallese di Oppeano – Verona
Tel. 045/7134674 Fax 045/6984019 beper.com
CUSTOMER CARE BEPER
http://customercare.beper.com/support/home
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>