beper P206VEN130 Stand Fan with Timer Instruction Manual
- June 3, 2024
- beper
Table of Contents
beper P206VEN130 Stand Fan with Timer Instruction Manual
Precautions
Read the following instructions carefully, since they give you useful
safety information about installation, use and maintenance and help you avoid
mishaps and possible accidents.
Remove the packing and make sure that the appliance is intact, with special
attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not have to be
accessible to the children, in order to preserve them from danger sources. It
is recommended not to throw these packing material in the domestic waste, but
to deliver them to the appropriate station of collection or destruction
refusals, asking eventually information to the manager of the Sanitation
Department of your own municipality.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds
to the data specified on the label.
The appliance can be damaged if the voltage is not correct.
If the plug does not suit the socket, let it be replaced with another suitable
plug by qualified personnel only, which shall also ensure that the section of
the socket cables is suitable for your appliance power absorption.
Generally, the use adaptors multiple plugs and/or extensions is not
recommended; should they be necessary, please use only simple or multiple
adaptors and extensions in compliance with the safety rules in force, making
sure that the capacity absorption limit marked on the simple adaptors and the
extensions and the maximum power limit marked on the multiple adaptor are not
exceeded.
Do not use the appliance if the cable or the plug shows any damages.
Do not use the appliance after a possible irregular working. In this case,
switch it off and do not break it open. Refer to an authorized Beper after-
sale service for repair and require original spare parts only. Failing to
follow these instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is
to be considered as improper and thus dangerous. The manufacturer cannot be
responsible for any damages deriving from improper, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of
the appliance into water or other fluids.
Do not use the appliance near explosives, highly flammable materials, gases or
burning flames.
Do not allow children, disabled people or every people without experience or
technical ability to use the appliance if they are not properly watched over.
Close supervision is necessary when any appliance used by or near children.
Some warnings
Do not plug the supply cord before assembly every parts of the fan.
Before using, check the integrity of the supply cord and eventually remove
possible nodes.
Place the fan on a flat and stable surface in a dry place.
Keep away to a reasonable distance the fan from walls, doors, windows or every
object that could avoid the appliance to work in the correct way.
Do not cover the body or grid of the fan when the appliance is working.
Do not plug objects into the grid or inside the appliance.
Do not pull on the supply cord to unplug the appliance.
After using the fan, unplug the cord supply.
If the fan must be stored for a long period or non-used, replace the fan in
the original packaging in a dry place. For every next use, check that the fan
is clean and that the blades turn in the correct way (motor off).
Description of the item
Fig.A
- Front grid
- Closure nut
- Nut blades
- Blades
- Rear grid nut
- Rear grid
- Motor
- Swing button
- Body motor
- Inclination set button
- Timer
- Control panels
- Screw for pipe
- Internal pipe
- External pipe
- High adjustment handle
- Screw pipe coupling with clamping washer
- Base
Assembly instructions
Put the base on the floor.
Insert completely the internal pipe inside the external pipe.
Fix the high adjustment handle.
Fix the external pipe to the base with the screw (included in packaging).
Take off the external pipe, and regulate it until the desired height. Strongly
screw the high adjustment handle.
Place the control panels on the pipe.
Screw completely with the screw in order that the control panels is well fixed
to the intern pipe.
Place the rear grid on the motor, in order that the holes of the grid are well
inserted into the motor of the fan Strongly and completely screw the rear grid
in order to block the grid on the motor.
Insert the blades of the fan on the motor and completely screw the nut blade
on the motor, in order to block the body motor.
Assembly the 2 grid front and rear ones by inserting the closure nut, place
the front grid, on the rear grid. Close the nuts to block the grids.
Speed selection
Choose the speed desired pressing on the buttons of the control panels.
Position 0 the fan switch off.
Position 1 low speed.
Position 2 medium speed.
Position 3 high speed.
Timer
The timer can be set from 10 to 60 minutes by turning the knob on the control
panel. Once the time set has expired, the fan will shut off automatically.
Head inclination
It is possible to choose various positions and change the air flow swing.
Before changing it, switch off the fan.
Take the motor body, unscrew the regulation axis and change the inclination of
the fan as desired and screw the air strongly.
Attention: do not try to force the inclination position in order to avoid any failure.
Swing
When pressing the swing button, It is possible to activate or disconnect the
swing of the fan, by touching the swing button. Swing allow to provide the air
uniformly.
To activate the push the swig button down until is completely blocked ; the
head fan turns automatically from right to left. To disconnect the swing raise
completely the button.
Cleaning
Before cleaning, switch off and unplug the fan.
For cleaning use a soft cloth, that may be softly wet.
Do not use alcohol or chemical substances, or any detergent that could damage
this appliance.
Do not spray water or other liquids on the fan in order to protect it.
After cleaning, dry every parts before using the appliance.
During the winter and when not used, keep this appliance in a dry and clean
place.
Technical data
Power: 40W
Power supply: 220V ~ 50Hz
For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.
The European directive 2011/65/EU on Waste Electrical and Electronic Equipment
(WEEE), requires that old household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order to optimize the recovery and recycling of the
materials they contain, and reduce the impact on human health and the
environment.
The crossed out “wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance, it must be separately
collected.
GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee applies to material and production defects. The purchase receipt and the guarantee certificate must be submitted together in case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance.
For any technical assistance, please contact directly the seller or our head office in order to preserve the appliance’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non authorized persons will automatically void the guarantee.
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:
- The appliance has been used properly and for the purpose for which it has been intended.
- The appliance has not been tampered with, otherwise it is not maintainable.
- The purchase receipt shall be presented.
- The appliance showing a fair wear and tear shall not be covered by this guarantee.
Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the appliance will be replaced free of charge.
In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product
Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>