beper P204FER200 Travel Iron Instruction Manual

: June 3, 2024
: beper

Table of Contents

beper P204FER200 Travel Iron
Use advice
Description of the product
Steam ironing
Dry ironing
Setting the temperature
Cleaning of the iron
Technical data
GUARANTEE CERTIFICATE
Documents / Resources

beper P204FER200 Travel Iron

$beper-P204FER200-Travel-Iron-fig- $3$$

Precautions

Read the following instructions carefully, since they give you useful safety information about installation, use and maintenan-ce and help you avoid mishaps and possible accidents. Remove the packing and make sure that the appliance is intact, with special attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not have to be accessible to the children, in order to preserve them from danger sources. It is recommended not to throw these packing ma-terial in the domestic waste, but to deliver them to the appropriate station of collection or destruction refusals, asking eventually infor-mation to the manager of the Sanitation Department of your own mu-nicipality.
If the supply cord is damaged, it must be replaced by the manufac-turer, its service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds to the data specified on the label.
The appliance can be damaged if the voltage is not correct.
If the plug does not suit the socket, let it be replaced with another suitable plug by qualified personnel only, which shall also ensure that the section of the socket cables is suitable for your appliance power absorption.
Generally, the use adaptors multiple plugs and/or extensions is not recommended; should they be necessary, please use only simple or multiple adaptors and extensions in compliance with the safety rules in force, making sure that the capacity absorption limit marked on the simple adaptors and the extensions and the maximum power limit marked on the multiple adaptor are not exceeded.
Do not use the appliance if the cable or the plug shows any damages. Do not use the appliance after a possible irregular working. In this case, switch it off and do not break it open. Refer to an authorized Beper after-sale service for repair and require original spare parts only. Failing to follow these instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manu-facturer cannot be responsible for any damages deriving from impro-per, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of the appliance into water or other fluids.
Do not use the appliance near explosives, highly flammable mate-rials, gases or burning flames.
Do not allow children, disabled people or every pe- ople without experience or technical ability to use the appliance if they are not properly watched over.
Close supervision is necessary when any appliance used by or near children.

Use advice

This product is suitable only for short ironings.
Make sure that the mains voltage corresponds to the data specified on the rating label.
If the cord supply or plug are damage, or in case of electric shock, do not use the iron but make it repaired by an authorized assistance centre.
When using the iron for the first time remove the protection from the soleplate, if necessary use a soft cloth. Pay attention to do not scratch the soleplate with metallic object, as well as zip, buttons, etc. When use the iron for the first time the soleplate may diffuse a light smoke caused by evaporation of protective oil used in factory; that is not dangerous and smoke will disappear after some use. The power cable must always be free from knots or tangles. Never pull the supply cord to unplug the appliance.
Do not roll up the electric cord around the iron.
Keep away to a reasonable distance the supply cord from the iron plate, especially when it is hot.
When making a break or if not used, put the iron in vertical position.

The plate of the iron becomes very hot so take care not to burn yourself.

Always choose the most suitable temperature for the cloth to iron. Do not use the iron as a heater. Do not subject the iron to shocks. Before cleaning, always unplug the power cord.
If you decide not to use the product any longer, you must place it away from children and in order not to create any danger.

Description of the product

Fig. A beper-P204FER200-Travel-Iron-fig- 2

Soleplate
Steam switch
Thermostat
Volt slide button
Working indicator light
Foldable handle
Steam button
Water tank lid
Water tank
Handle lock/unlock button
Power cord

Attention : the soleplate is very hot, do not touch during use!Keep the iron away from children.

Ironing

After preparing all the necessary for the ironing, unroll the power cable and check that it is free from knots or tangles.
Lift the handle by pressing the appropriate button.

Attention : before connecting the plug to the mains, check that the voltage selection button is posi-tioned correctly according to the mains voltage in the country where you are located

Check if the water tank is full; if you want to use steam, you should fill the tank with water (see the specific pa-ragraph).
Turn the thermostat to the position “MIN”.
Fill the water tank with sufficient quantity.
Place the iron vertically, paying attention that the soleplate will not come in contact with objects or anything else. Insert the plug into the socket.
Set the thermostat to the desired temperature, referring to the symbols printed on the thermostat.
At this point, you can start ironing.

Steam ironing

To iron with steam move the steam switch to the back.
When using the iron for the first time, press several times on the steam shot button, so that the impurities that during the construction of the iron deposited inside the holes will be eliminate.
Steam ironing is possible by adjusting the thermostat to the position marked by the symbol (•); increasing the temperature also increases the jet of steam, up to the maximum marked by the symbol (•••).
The working indicator light turns on and when the soleplate will reach the temperature (temperature that allows the steam to escape) it switch off.
Press the steam shot button and the steam will come out.
Respect a 5 seconds interval between one shot of steam and another.
If the steam shot button will be press before reaching the set temperature, the water will not come out vaporized but will drip from the plate; this can cause ironing spots on the garment.
Water dripping can also be caused by prolonged pressure of the steam jet button. (More than 5 seconds)
At the end of the operation, place the iron in vertical position and disconnect the plug from the socket.
The iron must be constantly on movement on the fabric to be ironed.

Warning : always direct the steam jet in the direction of the garment to iron, never towards the face. After ironing, always empty the tank of the remaining water, after having unplugged the plug from the electrical socket.

Dry ironing

To dry iron move the steam switch forwards to deactivate the steam outlet.
Adjust the soleplate temperature by turning the thermostat.
The working indicator light turns on and when the soleplate is at temperature it turns off. Start ironing after the iron has reached the desired temperature.

Note that in this case, the plate reaches lower temperature values, compared to steam ironing. At the end of the operation, place the iron in vertical position and disconnect the plug from the socket. The iron must be constantly on movement on the fabric to be ironed.

Setting the temperature

Always check the label with the ironing instructions on the article to be ironed and follow them.
Turn the thermostat knob to set the desired temperature, following the legend below. $beper-P204FER200-Travel-Iron-fig- $1$$

The number of dots in the thermostat indicates the temperature from the lowest (•) to the highest (•••). The table is valid for fabrics and not for finishes such as shiny or relief of the fold which must be ironed backwards. Before using the iron, always make sure that the temperature of the iron is correct with the type of fabric: wool with wool, cotton with cotton, etc.
The iron is quick to heat up and slow to cool down; so start ironing clothes that require low temperatures (such as synthetic fabrics) and go in progression with higher and higher temperatures.
When the item to be ironed is made up of several fabrics, adjust the temperature for the most delicate fabric. If you do not know the type of fabric to be ironed, it is recommended to iron a part of it, normally not visible when the garment is worn, starting from the minimum temperature, and then finding the most suitable temperature. It can happen that the garment becomes shining, in this case you need to finish ironing so as not to ruin it and iron the fabric from the reverse side.

Fill in and empty the tank

This operation must always be done with the plug disconnected from the socket.
Always dry the body of the iron from any drops and your hands before reconnecting the plug to the socket. Make sure the thermostat is positioned in the minimum position and the steam activation button is off.
Lift the tank lid and slowly fill the tank using a small glass or funnel.
Do not exceed the maximum level of the tank indicated on the tank itself.

Be careful not to let water penetrate the cracks in the iron, there is a risk of short circuits and/or electric shock. At the end of the filling, close the tank lid and connect the plug to the electric socket.

Note: The iron is designed to use tap water, however, if the water is very hard, it is advisable to use a mixture of distilled water and tap water.
It is suggested to empty the water tank after each use, in order to avoid the formation of limescale, mold and bad smells. It is recommended to let the iron cool down for a few minutes before emptying the tank.
To empty the tank, turn the iron upside down on a sink (or similar) and drain all the water still left in the tank. Otherwise, place the iron in vertical position and reconnect the plug to the electricity.
Place the thermostat on “MAX” and allow the residual water to evaporate in the tank for a few seconds, by pres-sing the steam button.

Cleaning of the iron

Unplug the appliance from the socket.
Remove the plug from the electrical outlet.
To remove scale or starch from the soleplate, use a damp cloth.
Always dry the soleplate after each cleaning.
Clean the body of the iron with a damp cloth without detergents.
Do not use metallic sponge or abrasive detergents.

Storage

Disconnect the power cable from the power outlet, empty the water tank (do this after each use) and let the iron cool down completely.
Wind the cord around the base.
To protect the soleplate, place the iron in vertical position.

Technical data

Power : 900-1100W
Power supply : 110-120V / 220-240V ~ 50/60Hz

For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.

The European directive 2011/65/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.

GUARANTEE CERTIFICATE

This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee ap-plies to material and production defects.
The purchase receipt and the guarantee certificate must be submitted together in case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance
For any technical assistance, please contact directly the seller or our head office in order to preserve the applian-ce’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non-authorized persons will automatically void the guarantee.

GUARANTEE CONDITIONS

If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:

The appliance has been used properly and for the purpose for which it has been intended.
The appliance has not been tampered with, otherwise it is not maintainable.
The purchase receipt shall be presented.
The appliance showing a fair wear and tear shall not be covered by this guarantee.

Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the appliance will be replaced free of charge.
In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product
Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.

YOU MIGHT ALSO LIKE

Steam Iron
Cod.: P204FER004 Stainless steel soleplate Continuous and vertical steam function Spray function and super steam shot Adjustable steam intensity and temperature Dry and steam ironing mode 2200W $beper-P204FER200-Travel-Iron- fig- $3$$