airLive 1004-10G Managed Switch Smart Network Solution Installation Guide
- September 17, 2024
- airlive
Table of Contents
airLive 1004-10G Managed Switch Smart Network Solution
Specifications
- Model: AirLive ONU-10XG(S)-1004-10G
- Speed: 10G DL / 2.5G UL
- Interface: LAN1-5, PON, USB 3.0
- Power: DC 12V, 1A
- Operating Temperature: -5°C to 55°C
- Operating Humidity: 10% to 90%
FAQs
Q: What do the different panel lights indicate?
A: The panel lights indicate various statuses such as power, registration, WAN connection, and interface status. Refer to the user manual for detailed descriptions of each light status.
Indicator and Interface Description
Product Picture
Application Chart
Panel Lights
| LED | Mark | Status | Description |
|---|
Power
|
PWR
| On| The device is powered up.
Off| The device is powered down.
Registration
|
PON
| On| The device is registered to the PON system.
---|---|---|---
Off| The device is not registered to the PON system.
Blink| The device is registering.
Optical signal|
LOS
| Off| The device has received an optical signal.
Blink| The device does not receive an optical signal.
WAN
|
WAN
| On| The WAN connection is up.
Off| The WAN connection is down.
Interface
|
LAN1-5
| On| The Port is connected properly (LINK).
Off| The Port is not connected properly.
Blink| Port is sending or/and receiving data (ACT).
USB
|
USB
| On| The USB device is connected but without ongoing
data transmission.
Off| The device is powered off or USB device is not
connected.
Blink| USB is with ongoing data transmission.
Interface/Button Panel
| Name | Function |
|---|---|
| ON/OFF | Power switch. |
| DC 12V | Connect with the power adapter. DC 12V, 1A. |
LAN1-5
| The silver LAN1 is a 10GE port and the yellow LAN2~5 are 1GE ports.
Connect PC or other devices to GE port by Cat5 cable, RJ-45 connector. And connect to the 10GE port by Cat6a cable, RJ-45 connector.
PON| Connect to OLT by SC type fiber connector, single mode optical fiber
cable.
RST| Press the RST button over 10 seconds, and ONU restores the factory
default and
reboots.
USB 3.0| External USB port, connect to USB storage device.
Packing List
| Contents | Quantity | Contents | Quantity |
|---|
10G-XG/XGS-PON
ONU
| 1 pcs| Power adapter| 1 pcs
Installation Guide| 1 pcs| Network cable| 1 pcs
Hardware Installation
Installation Environment Requirements
- ONU device must be installed indoors and ensure the following conditions:
- Confirm that there is sufficient space for ONU installation to facilitate cooling the device.
- ONU is suitable for working at temperatures ranging from -5 ℃ to 55 ℃ and humidity ranging from 10% to 90%.
- ONU workplaces should avoid high-frequency interference from radio transmitters, radar stations, and power equipment.
Equipment Installation
- Installed on the desktop Place the ONU on a clean bench, this installation is relatively simple, you can observe the following operation:
- Ensure a smooth surface.
- There is enough space around the device for heat dissipation.
- Do not place objects on the device.
Mounted on the wall
- The ONU chassis has two recesses on the back, in accordance with the position of the groove, install two screws in the wall.
- The mounting two mounting screws gently snap into recesses when aligned.
- Slowly let go, so that the device under the support of the screws is hanging on the wall.
Connect fiber, network cable, and power adapter to the corresponding interfaces, and turn on the power of the product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>