nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons User Guide

June 7, 2024
nanoleaf

nanoleaf logo Nanoleaf Elements
Wood Look Hexagons Starter Kit

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons -
partsnanoleaf NL52-K-7002HB-7PK
Elements Wood Look Hexagons -

User Manual & Warranty Registration
go.nanoleaf.me/myelements

Important Installation Tips

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons - enough
PSUs

Make sure you have enough PSUs for your layout.
NOTE: Each standard PSU supports up to 42W. Use our PSU calculator online at go.nanoleaf.me/myelements.

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons -
mounting

Before mounting your panels,  clean your surface to be free of dust, moisture, and oil.

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons - strong
pressure

To mount, apply strong pressure in a circular motion to the center of the panel for 30 seconds.

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons -
Controller

The Controller and Power Supply Unit can be connected to any panel in your setup.

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons - suitable for
textured

Tape is NOT suitable for textured, porous, popcorn, and ceiling surfaces (ie. wallpaper or brick walls).

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons -
1

http://qr.w69b.com/g/rB5aGSvJK

nanoleaf NL52-K-7002HB-7PK Elements Wood Look Hexagons -
2nanoleaf NL52-K-7002HB-7PK Elements Wood
Look Hexagons - 5nanoleaf NL52-K-7002HB-
7PK Elements Wood Look Hexagons - 1-2

WARNINGS & CAUTIONS Please read this safety information carefully and keep this document for future reference. Help articles and customer support is always available at http://go.nanoleaf.me/support. This Nanoleaf® product is not designed, certified, nor intended for use in: enclosed locations that limit the flow of air and/or trap heat which contributes to an environment temperature over 40 degrees Celsius; emergency exits, emergency lighting, or other use cases involving critical systems for human safety; in conjunction with 3rd party devices that are not approved by Nanoleaf® for use with Nanoleaf® products; locations or use cases where there is a risk of electric shock; outdoor areas, regardless of weather conditions; wet or damp conditions; as a floor covering or floor tiling; excessively hot environments that are consistently above 40 degrees  Celsius for extended periods of time (for example near ovens, space heaters, clothing dryers); excessively humid areas; regions or countries other than that in which the product was intended for and certified for sale in. When using this Nanoleaf® product: Do not open or disassemble the device, as this will void the warranty and make the product unsafe for use. While connected to the electrical supply of the building, line voltages will be present in the power supply, panels, linkers, so do not place any metallic or conductive objects near any exposed metal contacts on any component. Unplug the power supply unit from the power source before dismounting light panels. Do not allow small children to operate this device without adult supervision. This device contains small parts that may be a choking hazard to small children. Loose or dangling cords may cause an entanglement hazard to small children. Do not leave cords dangling or loose on the floor to help prevent accidents from tripping. Do not clean the device with liquid or spray when it is connected to power. Clean the panels with a soft dry cloth, and do not use harsh cleaning agents. Do not step on any part of the device, as this will cause breakage. Do not submerge any part of the device in water, or expose any part of the device to water. Do not bend or flex the panels with the connector still attached, as this will cause breakage. Do not attach the panels together with any connector or device other than original equipment manufactured by Nanoleaf®. Do not puncture any part of  the device with sharp objects, as this will cause the device to cease working as designed and may present a safety hazard. If the adhesive tape is a component of this product, please note that it is not designed to be used with unpainted brick walls, wallpaper, uneven/textured surfaces, or highly porous surfaces. If applicable, do not use double-sided tape to attach any part of the device to a ceiling or surface greater than 90 degrees relative to the floor, as the device will eventually fall down—creating a safety hazard and risk of damage to the device. Optional secure mounting solutions for these use cases are available, sometimes through added accessories offered for purchase separately. Your warranty DOES NOT COVER damage caused by falling devices. The flexible cable and power supply cannot be replaced by another third-party product. If the cable is damaged, the entire controller and power supply should only be replaced with original equipment manufactured by Nanoleaf®. Using any non-approved replacement component will void the warranty and may present a serious safety hazard. Nanoleaf® light panels are primarily intended for decorative use, with tunable white output function that can dim.
WI-FI/RF The normal use of your device does not allow users with a separation distance of less than 20 cm. The antenna is fixed with the device and not exchangeable by the end-user.

FREUENCY RANGE
2.4GHz Wi-Fi: 2412-2462 MHz, Max RF e.i.r.p power < 20 dBm
2.4GHz Radio: 2402-2480 MHz, Max RF e.i.r.p power<10 dBm
NFC: 13.56MHz, Max RF e.i.r.p power 0 dBm
CE INFORMATION NanoGrid Limited (Nanoleaf®) hereby declares that this device is in compliance with the essential requirements and other relevant provisions of  Directive 2014/53/EU. The declaration of conformity is available at https://go.nanoleaf.me/eudocs.
Disposal of your old product: Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. When this crossed-out wheelie bin symbol is attached to a product, it means that the product is covered by European Directive 2012/19/EU. Please find out about your local collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. The correct disposal of your old product will help to prevent potential negative consequences for the environment and human health.

Nanoleaf Canada

400 – 100 Front Street East

Toronto, ON
M5A 1E1, Canada
Nanoleaf Europe SAS
11 Rue de Lourmel
75015 Paris
France
Manufacturer
NanoGrid Limited

1301-483A Castle Peak Road,

Kowloon, Hong Kong| Models:
NL52-K-7002HB-7PK
FCC ID: 2AEWY-NL42
IC: 20489-NL42
Power Supply Specs:
Input Voltage: 100-240V~50/60Hz
Max Power: 16W
Communication Protocol:
Wi-Fi (2.4GHz b/g/n); 2.4GHz proprietary
---|---

Still Need Help?
go.nanoleaf.me/support

@nanoleaf
@thenanoleaf
nanoleaf.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals