nanoleaf NL55 Essentials Lightstrip Starter Kit User Guide
- June 5, 2024
- nanoleaf
Table of Contents
nanoleaf NL55 Essentials Lightstrip Starter
OVERVIEW
WARNING & CAUTIONS Please read this safety information carefully and keep
this document for future reference. Help articles and customer support is
always available at https://helpdesk.nanoleaf.me/. This Nanoleaf® product is
not designed, certified, nor intended for use in: enclosed locations that limit
the flow of air and/or trap heat which contributes to an environment
temperature over 40 degrees Celsius; emergency exits, emergency lighting, or
other use cases involving critical systems for human safety; in conjunction
with 3rd party devices that are not approved by Nanoleaf® for use with
Nanoleaf® products; locations or use cases where there is a risk of electric
shock; outdoor areas, regardless of weather conditions; wet or damp
conditions; excessively humid areas; regions or countries other than that in
which the product was intended for and certified for sale in. Risk of electric
shock – do not use where directly exposed to water. When using this Nanoleaf®
product: Always install the luminaire in accordance with your local building
code and consult a qualified electrician if necessary. Be careful not to damage
or cut the power wire insulation during installation. Keep all cords away from
sharp edges. Do not open or disassemble the device, as this will void the
warranty and make the product unsafe for use. Do not connect the device to the
electrical supply while it is in the packing or wound onto a reel. While
connected to the electrical supply of the building, do not place any metallic
or conductive objects near any exposed metal contacts on any component. Unplug
the power supply unit from the power source before moving the device. Do not
allow small children to operate this device without adult supervision. This
device contains small parts that may be a choking hazard to small children.
Loose or dangling cords may cause an entanglement hazard to small children. Do
not leave cords dangling or loose on the floor to help prevent accidents from
tripping. Do not step on any part of the device, as this will cause breakage.
Do not submerge any part of the device in water, or expose any part of the
device to water. Please note the adhesive tape provided with this product is
not designed to be used with unpainted brick walls, wallpaper, uneven/textured
surfaces, or highly porous surfaces. Do not connect this device to another
manufacturer’s product. The flexible cable and power supply cannot be replaced
by another third-party product. If the cable is damaged, the entire controller
and power supply should only be replaced with original equipment manufactured
by Nanoleaf®. Using any non-approved replacement component will void the
warranty and may present a serious safety hazard. It’s often unwise to stick
your fingers (or other parts of your person or conductive things connected to
your person) in dark places that you can’t see inside. Always practice safe
play with battery-operated and plug-in devices. Light strip installation not
be made on a radiant-heating ceiling
CLEANING AND MAINTENANCE Do not clean the device with liquid or spray
when it is connected to power. Clean with a soft dry cloth, and do not use
harsh cleaning agents. Manage in accordance with disposal laws in your area.
RADIO FREQUENCY RANGE Bluetooth, Thread: 2400-2483.5 MHz, Max RF e.i.r.p
power < 10dBm
CE INFORMATION NanoGrid Limited (Nanoleaf®) hereby declares that this device
is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EU. The declaration of conformity is available at
www.Nanoleaf.me/doc/.
WARRANTY INFORMATION This product is covered by a limited warranty from
Nanoleaf®: a two-year complimentary replacement of defective hardware. For
full details visit: Nanoleaf. me/warranty.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Nanoleaf Canada
-
400 100 Front Street East
- Toronto, ON
- MSA 1E1, Canada
Nanoleaf Europe SAS
- 10 Rue du Capitaine Ferber
- 92130 Issy-les-Moulineaux
- France
Manufacturer
NanoGrid Limited
1301-483A Castle Peak Road,
Kowloon, Hong Kong
References
- Shipping, Returns & Warranty | Nanoleaf » USA » Consumer IoT & LED Smart Lighting Products
- Products » Declarations | Nanoleaf » Europe » Consumer IoT & LED Smart Lighting Products
- Nanoleaf Helpdesk