Beldray 0515449 16 Inch Pedestal Fan User Guide
- June 7, 2024
- Beldray
Table of Contents
16INCH
PEDESTAL FAN
QUICK START GUIDE
Please read all of the instructions carefully and retain them for future reference.
Safety Instructions
When using electrical products, basic safety precautions should always be
followed. Check that the voltage indicated on the rating plate corresponds
with that of the local network before connecting the product to the mains
power supply.
Children younger than 3 years old should be kept away from the product unless
continuously supervised.
Children aged from 3 years and less than 8 years should not plug in, regulate
or clean the product or perform user maintenance. Children aged from 8 years
and people with reduced physical, sensory or mental capabilities or lack of
experience and knowledge can use this appliance, only if it has been placed in
its intended operating position and they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the
hazards involved.
Children should not perform cleaning or user maintenance unless they are older
than 8 years and supervised.
This is not a toy – children should be supervised to ensure they do not play
with the product.
This product contains no user-serviceable parts. If the power supply cord,
plug or any part of the product is malfunctioning or if it has been dropped or
damaged, only a qualified electrician should carry out repairs. Improper
repairs may place the user at risk of harm.
Keep hands, fingers, hair, and any loose clothing away from the rotating parts
of the product.
Do not leave the product unattended whilst connected to the mains power supply
or when in use.
Do not use the product for anything other than its intended use.
Do not cover the product.
Do not put objects into any of the openings. Always use the product on a flat,
stable surface.
This product is intended for domestic use only. It should not be used for
commercial purposes.
Warning: If a strong odor is emitted from the product, turn the unit off
and unplug it from the mains power supply
Care and Maintenance
Always wait until the fan has stopped completely and unplugged it from the
mains power supply before performing any cleaning or user maintenance.
Wipe the fan with a soft, damp, lint-free cloth and allow it to dry
thoroughly. Do not use abrasive cleaning solvents, polishes, or scouring pads
to clean the fan, as this may cause damage.
Description of Parts
1. 16 Inch Pedestal Fan main unit
2. Front grill
3. Rear grill
4. Oscillation switch
5. Motor assembly
6. Motor assembly unit bracket
7. Motor shaft
8. Small fixing screw
9. Head tilt screw
10. Fan blade unit
11. Logo plate
12. Adjustable cooling speed dial| 13. Washer
14. Grill screw with nut
15. Height adjustment screw
16. Base support weight
17. Base-locking screw
18. Grill-locking screw (qty. 4)
19. Fan blade screw
20. Large fixing screw
21. Large fixing screw cap
22. Adjustable base pole
23. Extension pole
24. Base
---|---
**Assembling the 16 Inch Pedestal Fan
**
STEP 1: Remove the washer and screw from the adjustable base pole.
STEP 2: Apply the base support weight to the base and install the
adjustable base pole with the washer and base-locking screw. STEP 3: Pull
out the extension pole and secure it by tightening the height adjustment
screw.
STEP 4: Remove large fixing screw and cap from the top of the extension
pole.
STEP S: Remove the small fixing screw and head tilt screw from the motor
assembly unit bracket.
STEP 6: Attach the motor unit to the extension pole by installing the
large fixing screw.
STEP 7: Reinstall the small fixing screw and head tilt screw on both
sides of the motor unit bracket.
STEPS: Install and tighten the large fixing screw cap to hold the motor
unit in place.
STEP 9: Remove the four grill-locking screws from the motor assembly
unit.
STEP 10: Install the rear grill with the handle at the top and facing out
towards the motor assembly unit using the four grill-locking screws.
STEP 11: Remove the rubber part from the motor shaft and turn the groove
of the motor shaft upwards.
STEP 12: Slide the fan blade unit onto the motor shaft, aligning and
tightening the fan blade screw to the groove.
STEP 13: Hook the front grill onto the rear grill, aligning both screw
holes at the bottom of each grill.
STEP 14: Install the grill screw and nut to lock the guards. Close the
clips.
STEP 15: Plug in the fan. Unplug after use.
Note: Take care not to overtighten the base locking screw as this could
cause damage to the base. Do not use tools to tighten the base-locking screw;
the base should be attached firmly so that when the fan is fully assembled,
the adjustable base pole and motor assembly do not wobble whilst the base
remains flat.
Take care not to overtighten the height adjustment screw as this may damage
the pedestal fan.
**Using the 16 Inch Pedestal Fan
**
STEP 1: To adjust the tilting angle, loosen the head tilt screw. Tighten
again at the desired tilt.
STEP 2: To switch the fan on, select speeds I-Ill on the adjustable
cooling speed dial. To switch the fan off, select 0.
STEP 3: Push the oscillation switch down to activate the oscillation
function. Pull knob up for normal operation.
Caution: Do not cover the fan head.
This is not a desk fan. Do not place the fan onto a desk as this could affect
the stability of the product.
Specifications
Product Code: EH3263
Voltage: 220-240 V – 50 Hz
Output: 50 W
If this product does not reach you in an acceptable condition please contact
our Customer Services Department at
www.beldray.com . Please have your delivery
note to hand as details from it will be required. If you wish to return this
product, please return it to the retailer from where it was purchased with
your receipt (subject to their terms and conditions).
Go to www.beldray.com and search EH3263 to
access the instruction manual for your product.
*To be eligible for the extended guarantee, go to www.beldray.com and register your product within 30 days of purchase.
The crossed-out wheelie bin symbol on this item indicates that this appliance
needs to be disposed of in an environmentally friendly way when it becomes of
no further use or has worn out.
Contact your local authority for details of where to take the item for
recycling.
Find us on
www.facebook.com/Beldray
Distributed by:
UP Global Sourcing UK Ltd.,
Victoria Street, Manchester OL9 ODD. UK.
MADE IN CHINA. www.beldray.com
CD251019/MD081020/V2
Manchester
OL9 ODD
United Kingdom www.upgs.com
t +44 (0) 161 627 1400
f: +44 (0) 161 628 2126
hk: +852 6681 9752
CN: +86 1 3417586804| Artworker: Ellie Drinkwater
Date:09/10/2020
Project Name: HCC194091 UPG EH3263 QSG
Type of Artwork: Quick Start Guide
Size: A4 Folding Leaflet Double-sided
Software Used: Indesign CC20
Typefaces: Avenir Next
---|---
| Cyan
---|---
Magenta
Yellow
Black
PMS
PMS
| PMS
---|---
PMS
**Artwork Version 3
**
Artwork Scale 1:1
©2020 UP Global Sourcing. All designs, images, and artwork are the copyright
of UP Global Sourcing. No copying, alterations, or amendments to the artwork,
design can be undertaken without prior written permission of UP Global
Sourcing. Any costs incurred as a result of unauthorized amendments will be
recovered from the supplier responsible.
DO NOT PRINT THIS PAGE ARTWORK REFERENCE ONLY
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>