super bright leds FUT012 Series RGB+CCT Bulbs User Manual

User Manual
MiBoxer Remote Pairing
Important: Read all instructions prior to installation.

Control Features

1. Master On/Off
   Acts as a master On (-)/Off (O) control for all linked RGBW and RGB+CCT lights. Also activates the Master function, which allows the remote to control lights of all zones. If a zone is currently active, pressing Master On (-) button on the remote or back button in-app restores the Master function to the remote.

2. Color Selection Ring Directly selects color along a circular spectrum. Press W button to change to a steady bright white.

3. Selection LED Indicator (wireless remote control only) Flashes once to indicate when a command has been selected.

4.  Brightness Touch Slider – Increase/Decrease Increases (right side) or decreases (left side) the brightness level. Changing active mode resets brightness level to full.

5. Saturation/CCT Touch Slider – Increase/Decrease Increases (right side) or decreases (left side) the color saturation level. When controlling white, adjusts from cool white (right side) to warm white (left side). \

6. Mode Nine distinct modes feature different color combinations, light transitions, and patterns. On wireless remote, this button initiates mode function and scrolls through modes in ascending order. In app, simply select mode button and press any numbered mode button to switch between modes.

7. Mode Speed Increase/Decrease Increases (S+ or +Speed) or decreases (S- or -Speed) speed of currently active mode.

8. Zones 1–8 On (|)/Off (O) Allows up to eight zones (channels) of RGBW and/or RCB+CCT lights to be separately linked and controlled by remote/app. Pressing any Zone On(|) button activates that zone. ommands will affect only lights in that zone. Once linked to a zone, lights remain linked until they are unlinked.

9. White LED Selection Switches to white LED operation. Note: While functions remain the same, the phone/tablet display will vary in appearance from remote control

Light Modes

brightness

Specifications

Safety and Notes

• For indoor use only
• White color temperature can not be adjusted unless white LED selection mode is active.

Compatible Remote Controls

One of these controls (available at additional cost) is required to control the bulb. Each light can be linked with up to 4 different remote controls (any combination of wireless remotes and Wi-Fi controls). Each control (and zone) can be linked to an unlimited number of lights.

Important: Read all instructions prior to installation.
RGB+CCT Bulbs
Parts Included
1 – WIFI-CON
1 – USB-500MA-5V
Setup Instructions
1. Download the MiBoxer app on a compatible device (iOS or Android).
2. See WIFI-CON manual for complete instructions on how to establish a connection and set up Wi-Fi control.
Note: Constant 2.4 GHz Wi-Fi connection is required for remote access to Wi-Fi control through your device.

Linking Lights to App Remote
Linking a Light

1. Press the Link/Unlink button (1).
2. Select the desired zone.
3. Follow the on screen instructions to link the light.
   Activating and Controlling a Specific Zone
   To activate a specific zone, select one of the available zones and press On button.
   Zone is now active and remote commands will only affect lights linked to that zone.
   Unlinking a Light
   1. Make certain the light is powered off.
   2. Press the Link/Unlink button (1).
   3. Select the desired zone.
   4. Press the unlink button to remove devices from the selected zone.

Wireless Remote Control

Parts Included
1 – RGBCCT-MZ8-RF
Setup Instructions
Install two AAA batteries (not included) into wireless remote. Note: Wireless remote operates using radio frequency and has 100 ft. (30 m) range.

Pairing Lights to Remote Control
** 1. Make certain light is powered off.
2. Apply power. Within 3 seconds, press and hold one of the eight Zone On (|) buttons until light begins flashing. Light will flash 3 times if successfully paired to selected zone.
Note: If encountering issues when pairing, instead try continually pressing the
desired Zone On (|) button repeatedly from before when power is applied to the controller until a few seconds after.
Activating and Controlling a Specific Zone**
To activate a specific zone, press Zone On (|) button for the desired zone. The zone is now active and remote commands will only affect lights paired to that zone.

Unpairing a Light
1. Make certain light is powered off.
2. Apply power. Within 3 seconds, press and hold Master On (|) button until light begins flashing. Light will flash 10 times if successfully unpaired.

FCC Statement

Applicable to controls only.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired . operation. Any changes or modifications in the construction of this device that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Rev. V3 Date: 02/08/21
4400 Earth City Expy, St. Louis, MO 63045
866-590-3533 superbrightleds.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>