CALEX 910181 Smart Outdoor Ground Spot RGB and Warm Light Instruction Manual

Ground Spot RGB and Warm Light
Instruction Manual

910181 Smart Outdoor Ground Spot RGB and Warm Light

This manual, A, contains descriptions of all necessary steps for assembling and installing this product. Refer to the icons in the supplementary manual, B, to see which of the  following points apply to this product:

|
---|---
|
|
|

B

This manual, B , contains descriptions of all parameters, specifications, and relevant icons in accordance with international standards and safety regulations. However, these do not always apply to the product you purchased. Refer to the icons in the supplementary manual, A , to see which of the following points apply to this product.

1. before installing this product, check which plugs and screws are best suited for the intended surface;

2. do not connect the product to a power supply while it is still in the package;

3. do not connect the product to a power supply while it is wound onto a reel;

4. do not use the product when covered or recessed into a surface;

5. do not open this product.

6. Safety Class I: this product must be connected to an earthed socket; the luminaire is equipped with a ground terminal and must therefore be earthed; connect the ground wire (yellow-green vein) to the -marked terminal.

7. Safety Class II: This product is double insulated and does not need to be connected to an earthed socket.

8. Safety Class III: this product is only suitable for very low safety voltage (e.g. 12V)

9. Intended use: only indoors

10. The luminaire must not be covered with insulating material.

11. The luminaire is not suitable for installation in the bathroom, at least not in the indicated area

12. The luminaire in only suitable for wall mounting

13. The luminaire is only suitable for ceiling mounting

14. The luminaire is suitable for wall and ceiling mounting

15. Strip the wire as indicated in the icon

16. IP20: This product is intended for use in dry spaces indoors
    IP23: Rain resistant
    IP44: Splashproof. The product is protected against the intrusion of solid objects greater than 1 mm in size and water spray from any direction.
    IP54: Protected from limited dust ingress, protected from water spray from any direction.
    IP65: The product is dustproof and protected from water jets. The luminaire cannot be used if the housing is broken.

17. This luminaire is (IP20) for components in the ceiling and (IP21) (IP23) (IP44) (IP65) for components under the ceiling, provided that this luminaire is installed correctly.

18. If the protective glass is damaged, it must be replaced immediately.

19. Always respect the minimum distance between the light source and the illuminated materials as indicated in the icon

20. Max… W: Use only lamps of the correct type and never exceed the maximum indicated wattage.

21. Use a heat-resistant cable to connect the luminaire to the mains

22. This luminaire is only suitable for lamps with built-in protection or ‘low-pressure lamps.
    An extra protective glass is not required.

23. The luminaire is equipped with a built-in fuse. If the luminaire does not work after replacing the lamp, this fuse must be replaced. If the fixed connection wiring of the installation can be touched, this may only be done by a qualified electrician.

24. This luminaire is suitable for top-mirror lamps

25. The luminaire is only suitable for fixed mounting and must therefore not be connected to a power source by means of a connecting cord.

26. Type X: If the external flexible cable or cord of this fixture is damaged, it will be replaced by a special cord or cord exclusively available from the manufacturer or its service agent. Type Y: If the external flexible cable or cord of this luminaire is damaged, it should only be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
    Type Z: the external flexible cable or cord of this luminaire cannot be replaced; If the cord is damaged, the fixture will be destroyed.

27. Note that no electrical or other wires in the ceiling or wall are touched during the installation of this luminaire.

28. Electrical installation wires must never be clamped or twisted (twisted) between the luminaire and the mounting surface.

29. This product is dimmable and compatible with a TRIAC dimmer.

30. This product uses LED technology and is only suitable for it.

31. The light source of this luminaire is not replaceable; when the end of the service life has been reached, the entire luminaire must be replaced.

32. Replaceable (LED only) light source by a professional

33. This product must not be covered by objects. Keep this product away from sharp edges, oils, and heat.

34. Never use this product in an area where there is a risk of explosion or near flammable substances or gases.

35. If this product is passed on to third parties, manuals must be included.

36. Keep this product out of the reach of children.

37. Turn off the product when you leave the room.

C3
Please check out our Smart Outdoor playlist on Youtube for more help and inspiration for this product.

https://www.youtube.com/watch?v=KMRjZM9RfhI&list=PL_PPMF5EN2LUlA1VbHtYlzOAWnvim3ZAi&ab_channel=CalexHolland

https://apps.apple.com/us/app/calex-smart/id1471978691
https://play.google.com/store/apps/details?id=com.calexsmart.smart

5 years of security updates for App, Cloud, and Tuya module firmware from the date of purchase.

Getting started

Before you start adding this Calex Smart product, write down the name and password, including spaces and capital letters, of your WiFi network. Make sure you have a strong  Wi-Fi signal.
Note: This item only works on 2.4GHz WiFi networks, not on 5GHz WiFi networks. If you get a message that the product only works on 2.4 GHz networks, then you need to change your network’s Wi-Fi frequency to 2.4 GHz in the settings menu of the router. Please contact your internet provider for this.
To use Bluetooth Mesh, the CalexLink is required.

1. Download the Calex Smart app from the Google Play Store, or the Apple Store or scan the QR code.

2. Open the app. Are you using the app for the first time? Then follow the instructions on the screen to create your account.

3. Turn the lamp set on. Do you have Bluetooth on your phone and is it turned on?
   Then a connection is made automatically. Can’t connect automatically? Then add this set by touching the + (top right corner of the screen). Follow the prompts to complete the installation. For more information, see our website: www.calex.eu 

4. Reset: You may need to reset the product first. You do this by switching the set off and on again three times. The lamps will start blinking. Then proceed with step 3.

D

Declaration of Conformity

We, Electro Cirkel Retail BV, as importers declare that this “radio equipment” is produced in China. The products passed all tests according to all relevant CE standards and regulations. The complete list of harmonized standards regarding directive 2014/53/EU can be found at: ec.europa.eu/growth/single- market/european-standards/harmonised-standards_en

The complete Declaration of Conformity can be found at www.calex.eu. For other compliance-related information please contact:
Website: www.calex.eu,
email: info@calex.eu,
Phone: +31(0)10-2981980
Postal: Lyonstraat 29, 3047 A], Rotterdam, the Netherlands

References

• Calex - Creators of Ambiance

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>