BlissLights 900-00048_A Ark Laser Projector User’s Guide
- September 13, 2024
- BlissLights
Table of Contents
- BlissLights 900-00048_A Ark Laser Projector
- NOTICE
- INTRODUCTION
- BEFORE YOU BEGIN
- PARTS LIST
- SETTING UP THE LASER PROJECTOR
- DEFAULT SETTINGS
- INSTALLATION TIPS
- PRODUCT SPECIFICATIONS
- BLISSLIGHTS LIMITED WARRANTY
- FAQs
- Video- BlissLights 900-00048_A Ark Laser Projector
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BlissLights 900-00048_A Ark Laser Projector
NOTICE
CAUTION—Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This product is classified as a Class 3R laser product and complies with the applicable parts of IEC/EN 60825-1 Ed. 2.0:2007 and Ed. 3.0:2014.
The manufacturer additionally certifies it complies with the US FDA Federal
Laser Product Performance Standard (FLPPS) provided in 21 CFR Subchapter J,
1040.10 and 1040.11 except for allowable deviations specified in FDA Guidance
documents.
Do not stare into the beams emitted from the product. Intentional long-term
viewing of CLASS 3R levels of laser light can be hazardous. This product uses
diffractive optics to scatter the beam energy. This scattering effect causes
the energy concentration to drop below the exposure limits for momentary or
accidental viewing at a relatively short distance from the laser aperture. As
with all bright light sources, when you operate this device in unsupervised
general public areas, it is recommended that up-close access to the light be
restricted or prevented and the beams be directed into locations where persons
are not expected.
This laser display device incorporates a CLASS 3B laser system which, by
itself, may be hazardous. However, this laser display product incorporates a
protective housing and diffractive optics in its design so that there is no
exposure or human access to laser radiation during operation or maintenance
above the CLASS 3R limits. Each laser beamlet’s power is below the Class 3R
limit of 5 mW.
UNDER NO CIRCUMSTANCES shall attempts be made to open the protective housing
or operate the device if the aperture window is damaged.
All service to this laser display device requiring the protective housing to
be opened and/ or removed shall be performed by service personnel or their
authorized agents. Opening the protective housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES (18.5 km) OF
AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE RECOMMEND
THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS ARE PROJECTED INTO
THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR PROVINCIAL GUIDELINES FOR FURTHER
INFORMATION
INTRODUCTION
Thank you for purchasing the BlissLights Ark Laser Projector. This product is a unique indoor light fixture that uses patented laser and holographic technology to project an abstract transforming Ark against a drifting nebula cloud. Each unit provides up to 20 x 20 ft of coverage. It has maximum electrical usage of less than 5 Watts and operates in temperatures between 14°F to 95°F (-10°C to 40°C).
BEFORE YOU BEGIN
Immediately upon receiving the fixture, carefully unpack and check the carton contents to ensure that all parts are present and in good condition. Notify the retailer immediately and retain the packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. If the fixture must be returned, the fixture must be returned in the original factory box. Please see the parts list below for box contents.
PARTS LIST
- Laser Projector
- USB Power Cord
- USB to Wall Adapter
IMPORTANT NOTE:
- Use only manufacturer-provided adapter.
- Use of 3rd party adapters may damage the unit and void the warranty.
- Adapter may vary from picture shown.
SETTING UP THE LASER PROJECTOR
Before operating your laser projector, please read the “Before you Begin” section and “Notice” section of this user’s guide.
- Insert the USB power cord into a powered USB port or use the included wall adapter to connect to an available electrical outlet.
- Place the Ark on a flat solid surface and aim toward desired ceiling/wall.
- Press the power button. The nebula and laser will gradually illuminateand begin moving by default.
- To adjust the illumination angle for walls, slide the unit down to the forward position.
- To turn off the light, cycle through the power button modes until the unit turns off completely. Remove the power plug from electrical outlet.
- Use the following buttons to control lighting effects:
- Button 1 (effects):
- Power on
- Pulse mode
- Laser only
- Cloud only
- Power off
- Button 2 (rotation):
- Rotation off
- Rotation on
- Button 3 (brightness):
- High
- Medium
- Low
DEFAULT SETTINGS
Once the laser projector is plugged in, it will enter the default mode where all effects are on. Use the buttons to change the effect settings and brightness. This light has a built-in timer that is designed to automatically shut off after 6 hours of operation.
INSTALLATION TIPS
- Do not connect the light to a dimmer pack, as a dimmer accessory may damage the laser component.
- The darker the display area, the brighter your projection will appear.
PRODUCT SPECIFICATIONS
| Laser Classification | Class 3R |
|---|---|
| Laser Wavelength | Green – 505nm ±5nm |
| Nebula Cloud Color | Blue – 450nm |
| Housing | ABS plastic |
| Power consumption | Less than 5 W |
| USB Power Adapter Input | 100-240 V ~ 50/60 Hz , 0.2 A |
| USB Power Adapter Output | 5V — 1A |
| Operation | Indoor |
| Operating Temperature | 14°F to 95°F (-10°C to 40°C) |
| Projection Coverage | Laser – 20 x 20 ft Nebula cloud – 15 x 15ft |
| Maintenance | Maintenance Free |
| Dimensions | 9”L x 3.5”W x 5”H |
| Cord Length | 5 ft (1.5 m) |
BLISSLIGHTS LIMITED WARRANTY
This product carries a limited warranty against defects in workmanship and
materials. BlissLights LLC agrees to replace the defective product free of
charge within the stated warranty period when returned by the original
purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse. For detailed warranty information for
your country, please visit
www.blisslights.com/warranty
CAUTION
This is not a toy. Young children must be supervised while using this device
at all times. This unit is not waterproof. Use and store indoors or in a dry
place.
CLEANING INSTRUCTIONS
Surface clean only with a soft, dry cloth. Unplug the unit before cleaning.
DISPOSAL
At the end of its serviceable life, this product should not be treated as
household or general waste. It should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
FAQs
What is the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector is a device that projects rotating laser effects and drifting nebula clouds to create an immersive, relaxing visual experience.
What technologies are used in the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector uses direct diode lasers, precision glass optics, and holographic technologies.
What colors does the BlissLights 900-00048_A Ark Laser Projector display?
The BlissLights 900-00048_A Ark Laser Projector features green and blue light effects.
Can the BlissLights 900-00048_A Ark Laser Projector be used outdoors?
The BlissLights 900-00048_A Ark Laser Projector is primarily designed for indoor use but can be used in sheltered outdoor areas.
Can the BlissLights 900-00048_A Ark Laser Projector be used outdoors?
The BlissLights 900-00048_A Ark Laser Projector consumes 5 watts of power.
How do you control the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector is controlled using a remote control that allows you to adjust settings, brightness, and rotation.
What is the coverage area of the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector can cover an area of up to 4000 square feet.
What materials are used in the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector features a plastic housing and a glass shade.
What type of mounting does the BlissLights 900-00048_A Ark Laser Projector use?
The BlissLights 900-00048_A Ark Laser Projector is designed for tabletop mounting.
What is the beam angle of the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector has a beam angle of 15 degrees.
What special features does the BlissLights 900-00048_A Ark Laser Projector offer?
The BlissLights 900-00048_A Ark Laser Projector features a motion sensor and multiple light effect modes.
What is the finish type of the BlissLights 900-00048_A Ark Laser Projector?
The BlissLights 900-00048_A Ark Laser Projector has an unfinished plastic finish.
How do you adjust the brightness on the BlissLights 900-00048_A Ark Laser Projector?
Brightness on the BlissLights 900-00048_A Ark Laser Projector can be adjusted using the remote control.
What are the dimensions of the BlissLights 900-00048_A Ark Laser Projector?
The dimensions of the BlissLights 900-00048_A Ark Laser Projector are approximately 5.91 x 2.76 x 2.76 inches.
Video- BlissLights 900-00048_A Ark Laser Projector
Download this Manual:BlissLights 900-00048_A Ark Laser Projector Users Guide
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>