MEEC TOOLS 012148 2-5T 57-510 mm Garage Jack Instruction Manual

: June 6, 2024
: MEEC TOOLS

Table of Contents

SAFETY INSTRUCTIONS
OPERATING INSTRUCTIONS
TECHNICAL DATA
USE
- LIFTING
- LOWERING
MAINTENANCE
- STORAGE
- BLEEDING
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MEEC TOOLS 012148 2-5T 57-510 mm Garage Jack Instruction Manual

SAFETY INSTRUCTIONS

It’s forbidden to use the jack to lift people.
Centre the load on the saddle before lifting.
Never work under a vehicle without blocking it up on pallet blocks (or equivalent).
Always chock the wheels on the vehicle and pull the handbrake on.
Do not push or lean on the vehicle when it is resting on the jack.
Only use the lifting points specified by the vehicle manufacturer.
Do not take the jack apart – risk of injury or malfunctioning.
Before lifting a vehicle, check that the jack is in good working condition.
Do not attempt to lift or support foundations, houses, caravans, trailers, campers etc.
The product is only intended to be used for lifting. Never attempt to move the vehicle when it is resting on the product.
Never overload the jack – risk of personal injury and/or material damage.
Only use the lifting points specified by the vehicle manufacturer.
The product is intended to be used on hard, level surfaces that can support the actual load. If the jack is placed on any other surface the product can become unstable and the load can fall.
Never go under a vehicle that is only lifted up with the jack.
Only use spare parts recommended by the manufacturer.
Failure to follow all the instructions and safety instructions can result in a risk of personal injury and/or material damage.

Symbols

| Read the instructions
---|---

| Approved in accordance with the relevant directives.

OPERATING INSTRUCTIONS

GARAGE JACK

Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions).

TECHNICAL DATA

Lifting power: 2.5 tonnes
Lifting height: 75 – 510 mm
Double pistons: Yes
Size: 724 x 342 x 153 mm
Weight: 30,6 kg

USE

IMPORTANT

Air in the hydraulic system can impair performance. Bleed the product before using for the first time by completely opening the lowering valve (turn the handle anticlockwise) and then press down the lifting saddle and pump rapidly several times with the pump handle.

LIFTING

Close the lowering valve by turning the handle clockwise until it resists. Do not overtighten.
Place the product under the object to be lifted. Check that the middle of the lifting saddle comes directly under the part that is to be lifted. Check that the lifting saddle is correctly positioned by lifting the object a little and checking that the product or the load cannot slip or move unexpectedly.
Lift the load by pumping with the handle to the required height. Block up the load immediately after lifting, with pallet boxes or the equivalent. Never let the load rest only on the jack.

LOWERING

Turn the handle anticlockwise slowly.
The lowering speed depends on how much the lowering valve is opened.

MAINTENANCE

STORAGE

Always store the product in the fully lowered position with the handle upright.

BLEEDING

Bleed the product before using for the first time by completely opening the lowering valve (turn the handle anticlockwise) and then press down the lifting saddle and pump rapidly several times with the pump handle.

EU DECLARATION OF CONFORMITY

Jula AB, Box 363, SE-532 24 SKARA, SWEDEN

This declaration of conformity is issued under the sole responsibility of the manufacturer.

LOW PROFILE GARAGE JACK 2,5T/ 2500Kg

Item No. 012148

conforms to the following directives and standards

Machinery Directive 2006/42/EC, EN 1494+A1:2008

This product was CE marked in year -20
Name and address of the person authorised to compile the technical file:
Viktoria Klaar Box 363, SE-532 24 Skara, Sweden

Skara 2020-02-18

Signature
Christian BLank
BISUNESS AREA MANAGER