MEEC TOOLS 015277 416 l/min 1300W Submersible Pump Instruction Manual

416 1/min
1300W
SUBMERSIBLE PUMP Item no.015277
SUBMERSIBLE PUMP
OPERATING INSTRUCTIONS

Important!
Read the user instructions carefully before use.
Save them for future reference.
(Translation of the original instructions).

Care for the environment!

Recycle discarded products in accordance with local regulations.
Jula reserves the right to make changes. For the latest version of operating instructions, see www.jula.com

DECLARATION OF CONFORMITY
Item number
015277
Jula AB, Box
363, SE-532 24 SKARA,
SWEDEN
This declaration of conformity is issued under the sole responsibility of the manufacturer.!
SUBMERSIBLE PUMP
230V, 1300W, 25000LJH

Conforms to the following directives, regulations, and standards:/

Directive/Regulation

|

Harmonized standard

---|---
MD 2006/42/EC| EN 60335-1:2012+A11+A13, EN 60335-2-41:2003+A1+A2, EN 62233:2018
EMC 2014/30/EU| EN 55014-1:2017+A11, EN 55014-2:2015, EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1
RoHS 2011/65/EU + 2015/863| EN 50581:2012

This product was CE marked in year:! Produkten CE-marktes ar:/ CE-gemarkeerd in het jaar: -21
Skara 2021-03-31

Mattias Lif
BUSINESS AREA MANAGER (Signatory for Jula and authorized to compile the technical documentation.
technische documentatie

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial, or mental disabilities, or persons who lack experience or knowledge if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.

• Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision.

• Familiarise yourself with the controls on the product and how to use them. Read all the instructions and safety instructions before use. Failure to follow all the instructions and safety instructions can result in a risk of electric shock, serious personal injury, and/or material damage.

• Contact the retailer or qualified personnel if you have any problems or questions.

• Store these instructions so that they are readily available for everyone who uses the product. These instructions should be enclosed with the product if it is sold or passed on.

• Do not make any modifications to the Only use accessories recommended by the manufacturer.

• The product must only be used for its intended purpose and in accordance with these instructions. The product must only be used for its intended purpose and in accordance with these instructions, otherwise, there is a risk of personal injury and/or material damage.
  The manufacturer cannot accept liability for personal injury and/or material damage resulting from improper use.

• A damaged cord or plug must be replaced by an authorized service center or qualified person to ensure safe use.

• Do not use the product if it is damaged. Always check the power cord, plug, and casing before use. If the product is damaged, or not working properly, it must be repaired or discarded.

• Pull out the plug immediately if the power cord or product gets damaged or stops working properly, otherwise, there is a risk of electric shock.

• Qualified personnel must carry out Imperfect repairs that can result in a risk of electric shock, serious personal injury, and/or material damage.

• Do not pull the power cord to pull out the

• Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces.
  Avoid kinking or bending the power cord.

• If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the

• If the product is used outdoors, only use an extension cord approved for outdoor

• The product is not intended to transport water for human consumption.

• Do not use the product to transport corrosive, flammable, or explosive substances such as petrol or other petroleum products, nitrogenous liquids, grease, oil, saltwater or wastewater from toilets, or liquid that has a higher viscosity than water.

• The temperature of the pumped water must not exceed 35°C.

• Keep this product out of the reach of

• Do not use the product if there are any persons in the water.

• Make sure the product does not suck up aquatic animals, such as fish.

• Pay attention to the risk of contaminating the liquid as a result of leaking lubricant.

• Protect electrical connections from

• Do not expose the product to temperatures below 0°C. Make sure that the product is not run without water.

• Do not pump aggressive liquids or abrasive material.

• Do not pull the power cord or float switch cord to move the product, and do not use them to secure the product from moving.

• The product is only intended for household use and is not suitable for commercial purposes.

• The manufacturer cannot accept liability for personal injury or material damage resulting from improper use.

IMPORTANT:
The product must be connected to the mains with a residual current device of a max of 30 mA.
SYMBOLS

| Read the instructions.
---|---
| Approved in accordance with the relevant directives.
| Recycle discarded products in accordance with local regulations.

TECHNICAL DATA

DESCRIPTION

The robust submersible dirty water pump can handle particles up to 40 mm. The pump is suitable for general pumping, extraction, and circulation of clean and dirty water, but not drinking water. It has a vertical outlet and a level monitor that can be used in both automatic and manual modes. To ensure that this pump lasts a long time the pump housing and impeller are made of cast iron, while the motor body and foot are made of stainless steel. Minimum water level to start: 150 mm. Residual level 55 mm.

USE

CONNECTION OF OUTLET TUBE

1. Screw the outlet tube on the outlet connection. All the connections should be sealed with jointing tape.
   • When using a hose, screw a suitable hose adapter on the outlet connection.

2. Press the hose firmly on the hose adapter and secure it with a hose clip.
   • A suitable hose can be used for temporary use. For permanent installation, a tube and non-return valve are recommended to prevent return flow when the product is switched off.

3. Fasten a suitable line to the handle and lower the product at an angle into the water, so that no air remains underneath the product —this prevents suction.
   Once the product is submerged, it can be straightened up.

4. Place the product on the bottom of the tank. Fasten the end of the line securely when the product is lowered down.
   The product can also be used suspended from the line. The product is ready to use when it is connected to the power supply.

NOTE:

• The product needs a free space of at least 60 x 60 cm. The maximum submersion depth is indicated in the technical data.
• Install the product so that the intake opening cannot be blocked.
• Do not use the product to transport corrosive, flammable, or explosive substances such as petrol or other petroleum products, nitrogenous liquids, grease, oil, saltwater or wastewater from toilets, or liquid that has a higher viscosity than water.
• The temperature of the pumped water must not exceed 35°C.

LEVEL ADJUSTMENT
The product must have a float switch that starts and stops the pump automatically.
The float switch must be fastened so that it can float freely and start and stop the product. The float switch can be set variably by undoing the screws and adjusting the free length of the cord.
FUNCTION CHECK BEFORE STARTING
Check the function of the float switch by carefully lifting it up and lowering it down to check that it closes and switches correctly.

1. Adjust the position of the float switch so that the water level is controlled The gap between the top of the float switch and the float line adjuster must not be too small, otherwise, the float switch will not work properly.
2. Make sure that the float switch does not reach the bottom before the pump stops.

WARNING: Risk of running dry.
NOTE:

• Risk of material damage. Do not lift the product by the cord or the outlet tube, they are not designed to support the weight of the product. The float switch must be able to move so that the product cannot run dry.
• When used hanging on the line: Do not run the product without the outlet tube connected. Make sure the product does not turn around its longitudinal axis. If the product is used hanging from the line, the line must be checked at regular intervals for wear and damage.

MAINTENANCE

CLEANING
Clean the outside of the product. Rinse with clean water. Remove stubborn stains with a brush and detergent. Lower the product into a container with clean water and run for a short time to flush the inside of the product.
NOTE
Clean the product after it has not been used for some time to prevent any deposits or contaminants from causing a blockage.
STORAGE
If there is a risk of frost, dismantle and clean the product and its accessories and store them in a frost-free place.
NOTE
Risk of material damage. The product and its accessories contain water, which means that they can burst if the water freezes.

TROUBLESHOOTING

The troubleshooting guide on the next page is used to identify the causes of common problems and how they can be rectified. Contact the retailer if the problem can not be rectified with the help of the troubleshooting chart. Contact the retailer if you cannot solve the problem with the troubleshooting chart.
The warranty does not cover damage resulting from repairs or attempted repairs carried out by unauthorized persons.

TROUBLESHOOTING CHART

Problem

| Possible cause|

Proposed action

---|---|---
The product will not start.| No power.| Check the power supply.
The float switch has not tripped.| Lift up the float switch.
No flow of water.| The inlet is blocked.| Clear the inlet.
The outlet hose is clinched.| Adjust the hose.
The product does not stop.| The float switch cannot sink far enough.| Place the product correctly on a level surface on the bottom of the well.
The flow of water was reduced.| The inlet is blocked.| Clear the inlet.
Parts are worn as a result of contaminants.| Clean the pump and replace worn parts.
The product starts but soon stops.| Contaminants in the water can cause the overheating protection to trip and stop the motor.| Disconnect the power supply and clean the pump.
Hot water can cause the overheating protection to trip and stop the motor.|

Make sure that the temperature of the pumped water is no more than 35°C.

JULA AB, BOX 363,
SE-532 24 SKARA 2022-03-08
©Jula AB

Documents / Resources

| MEEC TOOLS 015277 416 l/min 1300W Submersible Pump [pdf] Instruction Manual
015277, 015277 416 l min 1300W Submersible Pump, 416 l min 1300W Submersible Pump
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>