CREATE Humizen Pro Ultra Humidifier and Aroma Diffuser User Manual

CREATE Humizen Pro Ultra Humidifier and Aroma Diffuser

Thank you for choosing our humidifier. Before using the appliance, and to ensure the best use, carefully read these instructions. The safety precautions enclosed herein reduce the risk of death, injury, and electrical shock when correctly adhered to. Keep the manual in a state place for future reference, along with the completed warranty card, purchase receipt and package. If applicable, pass these in­structions on to the next owner of the appliance. Always follow basic safety precautions and accident-prevention measures when using an electrical appliance. We assume no liability for customers failing to comply with these requirements.

SECURITY INSTRUCTIONS

When using any electrical appliance, basic safety precautions should always be observed.

• Please follow all the safety precautions listed below for safety and to reduce the risk of injury or electrical shock.
• This humidifier can be used by children aged from 8 years and above and persons with re­duced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the humidifier in a safe way and understand the hazards involved. Children shall not play with the humidifier. Cleaning and user maintenance shall not be made by children without supervision.
• Before using this humidifier ensure that the voltage of your electricity supply is the same as that indicated on the rating plate of the humidifier.
• Always place the humidifier on a hard, flat and level surface. Avoid exposure to direct sun­light and always keep it away from walls and heat sources such as stoves, radiators, etc. The humidifier may not work correctly if it is not placed on a level surface.
• Do not insert or remove the electric plug on the humidifier with wet hands.
• If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or a similarly qualified person in order to avoid a hazard.
• To reduce the risk of electric shock, do not remove screws. The humidifier does not contain any user-serviceable parts. Please leave all maintenance work to qualified personnel.
• Fill the tank with fresh, distilled or demineralized water. Do not drop any other liquid into the water tank. Do not run the humidifier when there is no water in the tank.
• Do not shake the humidifier as this might cause the water spill over into the base of hu­midifier.
• Never touch the water or any component while the humidifier is in operation.
• If there is an unusual smell when it is being used as described in this manual, switch the humidifier off, unplug it and have it examined by your dealer.
• Do not pour hot water into the tank, i.e. at a temperature over 40°C.
• Unplug the humidifier before cleaning it or removing the tank.
• Do not immerse the humidifier or the mains cable or plug in water or other liquids.
• Never scrape the transducer with a hard tool. The humidifier must be cleaned regularly. To do this, refer to the cleaning instructions in this manual.
• If you spill any liquid into the humidifier, it can cause serious damage. Switch it off at the mains immediately. Withdraw the mains plug and consult your dealer.
• Disconnect the humidifier from the power supply when not in use and before cleaning.
• Ensure that the mains cable does not touch any hot surface and that it does not overhang a table edge.
• Never use this humidifier in a room where aerosol products (sprays) are used or in a room where oxygen is being administered.
• Do not put items of clothing or towels on top of the humidifier. If the nozzle is obstructed, this may cause the humidifier to malfunction.
• When moving the humidifier, lift it by the base and not by the water tank.
• Do not use the humidifier if the air in the room is already sufficiently humid.
• The ideal relative humidity level for human comfort is in fact between 45% and 65%. Ex­cess humidity shows up in the form of condensation on cold surfaces or cold walls in the room. To measure the room’s humidity correctly, use a hygrometer available in most spe­cialist shops and hypermarkets.
• The humidifier is designed for indoor and domestic use only.

CHARACTERISTICS

WORKING PRINCIPLE
The ultrasonic humidifier uses the ultrasonic high-frequency oscillator to break up water into tiny water particles with a diameter of about 1-5 um. The ventilation system blows out this water into the dry air where they evaporate to give the required humidity. The clear­ly visible smooth and even fog can be seen out of the humidifier.

RELATIVE HUMIDITY

1. The percentage of water mist in a given space with a given air temperature is named relative humidity, usually marked as % RH, i.e. 45% RH. The air contains water mist more or less. The proportion of water mist to the air varies according to different air tempera­tures. The higher the temperature, the more water mist is inhaled in the air.
2. In winter, the cold air outside enters the room and becomes warmer by the higher tem­perature in the room. As a result, the relative humidity decreases. If you want to keep the healthy environmental humidity, we need to increase the mist volume in the air. The humid­ifier can do that for us.
3. Relative humidity in different environments suitable for people:

• Bedroom, living room: 45-65% RH
• Patient’s room: 40-55% RH
• Room with a computer, experiment equipment: 45-60% RH
• Room with a piano: 40-60% RH
• Museum, exhibition hall, and library: 40-50% RH

WATER FILTER
Ceramic balls can soften the hard water.
A ceramic filter can eliminate the strange smell in the water.

AROMA BOX

1. Press out the aroma box from the base.
2. Use water-soluble aroma oil and drop on onto the sponge.
3. Put the aroma box back into the humidifier, the aroma function will remain on when the humidifier is running.
4. To stop the aroma function or when storing the humidifier, clean the sponge in the aroma box.
5. Only drop the aroma oil into aroma cotton. Do not drop any liquid except clean water into the water tank.

PARTS LIST

1. Top cover
2. Handle
3. Nozzle
4. Water tank
5. Control panel
6. Host
7. Sensor
8. Power cord

DISPLAY

** CONTROL PANEL**

FEATURES

• Highly efficient in humidification with large output.
• Low energy consumption, save 85-90 percent of electricity than normal stream humidifier.
• Long lifetime.
• Automatic control of humidity level, lack-of-water security protection.
• Base with aroma cotton, to wet it with aromatic oil.

OPERATION INSTRUCTIONS

• The first operation: Put the humidifier in room temperature for half an hour before running.
• It is recommended to use the humidifier under a temperature of 20°C, with relative humidity less than 80% RH.
• Use clear water not over 40°C.
• Check the water tank, make sure it is clear.

1. Put the humidifier on a flat surface.

2. Remove the top cover, fill water into the water tank, and then put back the top cover. Or take out the water tank for filling water, afterward put the water tank back on the main base.

3. Check if the rated voltage meets the input voltage, and plug it into the socket. Then the display will light up and the buzzer will ring for once. 1 second later, the display turns off, only the red symbol POWER O is showing and the humidifier is in the standby state.

4. Touch the symbol POWER 0, display the background, and the water tank indicator light will light up meanwhile. A humidifier will begin to work in AUTO mode, with a display show­ing the AUTO 0 symbol and current humidity. 10 seconds later, the display shows the current temperature and then changes into humidity. Temperature and humidity showing will switch once in every minute.
   A humidifier will decide on running humidity based on the current temperature as below table.

5. Constant Humidity: Touch the symbol HUMIDITY 0, you may select the humidity range from 30% RH to 75%. Touch once, it will increase by 5% RH for each time. When it reaches 75%, touch again, it will show”–· and the humidifier will run back to AUTO mode.

6. After setting the expected humidity, the humidifier will keep the memory and confirm by flashing in 3 seconds. Once the display switches to show current humidity, it means the setting is finished,”%” on display will flash slowly.

   • When setting humidity is 1% RH – 9% RH higher than current humidity, mist output speed will run by the lowest (the first) speed.
   • When setting humidity is 10% RH – 15% RH higher than current humidity, mist output speed will run by the middle (the third) speed.
   • When setting humidity is 15% RH higher than current humidity, mist output speed will run by the highest (the fifth) speed.
   • When current humidity is higher than the set humidity, the humidifier will turn into a sleep state. Once current humidity is 3% RH lower than setting humidity, the humidifier will re­work in the previous working mode till water shortage.
     Mist output speed is adjustable under constant humidity function.

7. Night Mode: Long press symbol HUMIDITY O for 2 seconds to shut down water tank indicator light and display, only red ON/OFF symbol is showing. Press any symbol to wake up the light and display.

8. Timer: There are 12 timer setting: 1,2,3.4,5,6,7,8,9,10,11,12 hours. Touch the symbol TIM­ER C:1, the LED display will show the timer setting from 01-12 in sequence, for example “lH”. Once finished setting excepted timer, without operation for 3 seconds, the timer stop flashing means that the timer setting is successful.

   • The timer shows the rest operation time every minute and decreases by 1 hour, i.e., if the timer is set at 12 hours, the LED display shows 11 after 1 hour.
   • There is a shortcut for the timer setting. Long press the symbol TIMER C9 2 seconds to can­cel timer setting.

9. Disinfect: Symbol DISINFECT  first touch to start heating function, the display shows symbol HEATING  Warm mist wilt come out after 10. minutes. The second touch to start plasma function, display shows symbol PLASMA  plasma generator works as well. Third touch to shut down heating function. Fourth touch to shut down plasma func­tion.
   Long press symbol DISINFECT to turn on/off water tank indicator light.

10. 10. Mist Output Speed: Touch to enter manual mode, sliding from MIN to MAX to select desired mist output speed. Sliding from left to right, speed will increase from 1 to 5, with a display showing from 1 to 5 accordingly.
    Auto Shut-Off: Once the water in the tank is not enough to keep the humidifier contin­ue working, the humidifier will automatically stop working and will warn (ith 3 beeps (no sound under NIGHT mode). The display will show the water shortage symbol  only. Refill water tank, humidifier wilt restart after 5 seconds. Otherwise, the humidifier will automat­ically power off after 5 minutes.

REMOTE CONTROL

When first using the remote control, the plastic tab should be removed from the battery compartment.

1. On / Off
2. Speed
3. Humidity
4. Timer
5. Plasma
6. Auto

REPLACING THE REMOTE CONTROL BATTERY

1. Remove the battery compartment by pinching the tab and pulling the compart­ment out as below picture.
2. Remove the old battery.
3. Replace with a new battery. Make sure that the polarities match.
4. Replace the battery compartment.

TROUBLESHOOTING

PROBLEM                          POSSIBLE CAUSE SUGGESTED SOLUTION

The power lamp is off when SWitched on.

The power lamp is on when switched on, but no m1st comes out

| A humidifier is not plugged in.| Plug the humidifier into a powered electrical socket.
Power cord damaged.| ****

Immediately stop using and contact Customer Support.

–

Press the power button to tum it on.

A humidifier is defective or malfunctioning.
A humidifier is not Finedon.|

The target humidity is reached.

| Increase the target humidity or change mode.

Water shortegeindiaitor ison.

| No water In the tank.

–                                                                    –

Water levels are low.

| Refill the Weiler link and waIt for Ill. least

1 minute.

The water Levalrequired has not yet

reached the vaporization compartment.

| ****

Weit at least1minute.

The water tank isn’t well positioned.| Check the positioning of the tank on the

base.

The humidifier Isn’t on a flat sur- face.| ****

Check the positioning af the humidifier.

Humidifier produces an unusual smell.

| ****

A humidifier is new.

| Take out the water tank, open the cover, and let It stay12hoursin composed.
Dirty water or water sitting too long.| Clean water tank, fill with clear water.
The residual smell from diffusing aro-

mail on the aroma cott1XL

| Remove the aroma cotton, rinse It un-

der clean water and allow it to dry.

A humidifier makes a loud or unusual sound.

The humidification capacity is too low.

| Resonant In water tank when water is too low.| ****

Fill water into the water tank.

Humidifier jg on an unstable sur-

face.

| Move the humidifier to a stable flat surface.

The water tank is positioned incorrectly.

| Turn off the end unplug the humidifier, then align the water tank cover with its respective opening in the inner chem-

ber.

A humidifier is malfunctioning.| Immediately stop using and contact

Customer Support.                      –

—

There is natural or artificial air re-placement  in the room which interferes the increase of 96RH.

| Check if doors and windows are closed.
Check if there is no air conditioning working In the room.
The air inlet grids and nozzle could be blocked.| Remove any blocking items from the grid and s end the nozzle.
Toomuchscale in the water tank.| Clean transducer.
The humidity selected rate is too low.| increase humidity output speed.           –

Increase humidity settings rate.

Water is too dirty or water is kept too long in the tank.| Clean water tank. change to fresh cl.ear water.
PROBLEM| POSSIBLE CAUSE| SUGGESTED SOLUTION
---|---|---

To the ambient humidity is too high,

| A humidifier is working in a CONTINUOUS MODE.| Change the mode.
Thehumiditytareetis too high.| Select a lower96RH ta rgat.

The room is not well-ventilated.

–

Excess water tonk he sspilledwhile

filling the water tank or replacing the water tank back onto the base.

| Open a window to ensure proper airflow for the YoUr humidifier, or move the humidifier to a more well-ventilated room.

Wipe off excess water from the top

and bottom of the base before replacing the water tonk.

There is condensation in the room.

–

The mist suddenly stops coming out

| The room temperature is too low. The programmed timer period has run

-out.

The wetar shortoga ind ice tor is on.

| Heat the room up.

Tum humidifier on. Refill water tank.

Thetargethumiditylevelis reached.|

An incorrect humidity level is being displayed.

| The room is larger than the effective range of the humidifier.| Move the humidifier to a room that is suitable room size.

Mois11.lra has built up inside of the humidity sensor.

| Tum off the humidifier and allow the humidity sensor to completely air dry

before resuming use.

The nozzle is facing the directional

the humidity sensor.

| Tuatha nozzles that is facing away from the humidity sensor.
The humidity sensor is broken or defectlve.| Contact Customer Support.

Controlpaneldoesnot

work.

| Hands are too wet when operating rol panel

Humidifier has malfunctioned.

| Keep hands dry while operating the control penal.

Contact Customer Support.

| “”a       “”‘hmlo=I| Use distilled water with the dehumidifier.

If distilled water Is not available, use purified or filtered start. Remember to clean the water tank at least once a week.

Clean humidifier.

White dust appears around the humidifier.

modifier was not properly cleaned after last use.

Mist is coming out from water tank   i s no t positioned cor-| Tum off and unplug the humidifier, thenali1111thewatar tank cover with its respective opening in the inner cham-

bar.

–

Mist fog coming out from around the nozzle..

|
There are apertures between the nozzle and the water tank.| Reposition the cover and check If the nozzle is wall plugged in the cover.
|

The humidifier IsIn the warm-up phase.

| Wait e few minutes till the end ** of the phase.
The warm mist function does not produce warm mist| The mist is too fine to feel the**

warmth.

|

Increase the speed level.

The room temperature is too cold and the mist may cool down too|

Increase the speed level end haet the room up,

quickly.

Remot8controldoesnot

work.

| The remote control is out of range from the humidifier.| Use the remote control within 5 m of the humidifier.
The plastic tab blocks the battery.

–

The battery needs to be changed.

| Remove the plastic tab from the bat- very compartment.

R81)lease the battery.

The following is not considered faulty operation:

1. If your water is very hard (containing abnormally high levels of minerals) the humidifier may produce white dust. This is not a malfunction. The solution would be to clean the filter more often or use softer water.
2. If you stand very close to the humidifier, you will hear the gurgling sound of water. This is normal.
3. The humidifier operates very quietly but it is not completely silent. Noise levels less than 35 dB (A) is considered normal.

MAINTENANCE

• In case the water is hard, which means water contains too much calcium and magnesium, it can cause a “white powder” problem and leave heavy scales on the surface of the water tank, transducer and inner surface of the water tank. Scales on the surface of transducer will let the humidifier work improperly.
• We recommend:
  1. Use cold boiled water or distilled water.
  2. Clean the transducer, water tank, and basin humidifier every week.
  3. Change the water in the water tank more often to keep it fresh.
  4. Make sure to pour out water from the water tank and dry the water tank before you store it unused for a long time.
  5. Clean the whole humidifier and make sure that all parts of the humidifier are dried com­pletely if it is supposed to be left unused for a long time.
• How to clean the transducer:
  1. Clean with clean water or citric acid if there is a scale in it.
  2. Brush off the scale from the surface.
  3. Rinse the transducer with clean water.
• How to clean the water tank:
  1.  Clean the water tank with a soft cloth or use citric acid if there is a scale in it.
  2. If the scale is covering the security switch, drop citric acid for 2-5 min on the scale and clean it out with a brush.
  3. Rinse the water tank with clean water.
• How to clean the ceramic filter:
  1. Clean and activate the ceramic ball filter after using lO00L water regularly. Depending on water quality. If the ceramic ball is dirty, it needs to be cleaned more frequently.
  2. It can be dipped in vinegar for about 5 minutes. Then rinse it clean with clean water.
  3. Then put the filter under the sun for 4-6 hours.

In compliance with Directives: 2012/19/EU and 2015/863/EU on the restriction of the use of dangerous substances in electric and electronic equipment as well as their waste disposal. The symbol with the crossed dustbin shown on the package indicates that the product at the end of its service life shall be collected as separate waste. Therefore. any products that have reached the end of their useful life must be given to waste disposal centers specializing in separate collection of waste electrical and electronic equipment. or given back to the retailer at the time of purchasing new similar equipment, on a one-for-one basis. The adequate separate collection for the subsequent start- up of the equipment sent to be recycled, treated and disposed of in an environmentally compatible way con­tributes to preventing possible negative effects on the environment and health and optimizes the recycling and reuse of components making up the apparatus. Abusive disposal of the product by the user involves the application of administrative sanctions according to the laws.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>