THE GALLEY IPT-D Galley Pot Filler Tap and Rough-In Installation Guide

IPT-D Galley Pot Filler Tap and Rough-In

THEGALLEYTAP®

Installation Guide
Galley Pot Filler Tap and Rough-In
IPT-D
PFT-RO-SS

Before You Begin Installation

IN ACCORDANCE WITH AUSTRALIAN STANDARDS REQUIREMENTS IT IS RECOMMENDED THAT ALL TAPWARE  BE INSTALLED BY A LICENSED PLUMBER. PLEASE REFER TO THE WARRANTY CARD FOR SERVICE AGREEMENT.

1. Hot and cold water inlet pressures should be equal.

2. Inlet pressure range: 150-500kPa.

3. Pressure limiting valves should be installed where water pressure exceeds 500kPa.

Note: As per AS/NZS 3500.1-2003 (Clause 3.3.4) on new installations the maximum operating pressure at any  outlet within a building must not exceed 500kPa.

4. All pipework must be thoroughly flushed prior to installation, as foreign materials may block the flow regulating  device and reduce the flow of water. Aerator insert housing must be re-tightened to prevent removal by hand.

5. This mixer has a low flow rate and may not be suitable for connection to some Instantaneous Gas Water  Heaters, some Tempering Valves, some Solar Water Heaters & some Thermostatic Mixing Valves. Check with the  manufacturer of these products.

6. Not recommended for gravity feed systems, tank water systems or bore water systems.

7. Isolating stop taps must be fitted to the hot and cold water supply connections in accordance with local  authority installation codes.

Tools

Package Contents

IDEAL POT FILLER

Remove all contents from the package and identify before installation.
1 – Pot Filler Tap
2 – Pot Filler Trim

TECHNICAL INFORMATIONCARE

Operating Pressure: 145 PSI max (10 bar)
Recommended Operating Pressure: 14 – 60 PSI (1-4 bar)
Flow Rate: 4.2 GPM / 60 PSI

ROUGH-IN

Remove all contents from the package and identify before installation.
1 – Mounting Bracket
2 – Screws
3 – Inlet Housing
4 – Inlet Housing Cover

Before You Begin Installation

Before installing, Rough-in plumbing must be completed. The position of your Pot Filler Tap should be considered prior to starting. When fully extended from the wall, the reach of the Pot Filler Tap is 610 mm. Choose a position on the wall that allows the Pot Filler Tap to reach the furthest cooking position (Fig. 1). We recommend aligning the Pot Filler Tap to either the left or right side of the cooking surface. The Rough-in should be installed at minimum 330 mm from the cooking surface (Fig. 2). We recommend a height of no more than 457 mm.

Rough-In Installation

Step 1
Wrap the 13 mm inlet with Teflon tape.
Note: Wrap in the direction of the threads fully 2-3 times.

Step 2
Thread the housing onto 13 mm inlet. Rough-in should only be installed where the inlet connects on the left or right. Never install with the inlet opening on the inlet housing pointed upward or downward.

Note: 13 mm inlet threading not provided.

Step 3
Ensure mounting bracket is oriented properly and level along the vertical scale shown below.

Step 4
Use the minimum and maximum marks on the inlet housing cover to ensure proper position of the inlet housing once installed.
Note: Secure the mounting bracket to wall stud.
Note: Ensure minimum and maximum lines on inlet housing cover are properly positioned before mounting, taking into account the depth of the sheet rock and any backsplash. Maximum line will need to be visible once backsplash is installed to ensure proper installation.

Step 5
Wrap the 13 mm inlet with Teflon tape.
Note: Wrap in the direction of the threads fully 2-3 times.
Leave inlet housing cover in place until Pot Filler is installed.

Pot Filler Installation

Step 1
Remove inlet housing cover.

Step 2
Insert the Pot Filler trim piece into the inlet housing.

Step 3
Install Pot Filler Tap onto the trim piece with the centering pin positioned on the top right.

Step 4
With Pot Filler installed, secure it by using the set screw located on the bottom of the main body with a 10 mm allen key.

Step 5
Install Pot Filler Tap onto the trim piece with the centering pin positioned on the top right.
Fully extend and articulate the arm to ensure the Pot Filler is securely fastened to the inlet housing.

Pot Filler Usage

• Pot Filler Tap turns on by rotating handle counter clockwise (Fig. 1).

Maintenance:
Cartridge Replacement

Maintenance:
Outdoor Installation

Important – Your outdoor Galley Pot Filler Tap must be winterized if temperature falls below freezing in your area.

WINTERIZE YOUR GALLEY POT FILLER TAP:
• Turn off water supply and disconnect Hot and Cold Supply Hoses.
• Open handle to drain any water; drain completely.

Care and Cleaning the Galley Tap Finishes

ABOUT OUR FINISHES:

The Galley Tap is made of solid stainless steel. This finish has NO PROTECTIVE COATING on it. Stainless steel is by its material nature very tarnish- resistant, but by no means tarnish or stain proof. This finish will react to it’s environment over time. Cleaners that contain bleach may cause rust. Keep your Galley Tap wiped clean and dry, and use only a cleaner specifically made for stainless steel. Trapped moisture on the surface of your finish can lead to staining. Astringent cleaners, chlorine, bleach, and acidic-based organic cleansers are potentially harmful to stainless steel finishes.

IMPORTANT NOTICE:

It is the responsibility of the customer to check for any material finish defects BEFORE installation.

SUGGESTED FINISH MAINTENANCE PROCEDURE:

1. Do not allow water spots to dry on the fixture. Keep the surface clean and dry after use.
2. Periodic cleaning can be done by applying a stainless steel cleaner with a soft, clean cloth to gently remove surface spots and brighten the finish. For PVD finishes, clean with a soft, warm, damp cloth.
3. Never use cleaners with bleach, abrasives or vinegar. Never use any type of abrasive cleaning pad.

Pot Filler Replacement Parts

* XXX Represents Finish

1.O-Rings 0.027
2.O-Ring
3.Trim Ring
4.O-Ring
5.Anti-clockwise valve G 9.5 mm
6.Set screw M3X4
7.Stainless Steel Screw M4X10
8.Handle
9.Trim H59
10.Steel plug insert 5X16
11.Flat head set screw M5X8
12.O-Ring
13.Set screw M4X3
14.O-Ring
15.Set screw M3X4
16.Set screw 5X8
17.Set screw M4X3
18.O-Ring
19.Laminar Flow aerator
20.O-Rings

Rough-In Replacement Parts

1. Housing screws
2. Mounting bracket
3. Wood screws
4. Pot Filler inlet housing
5. Inlet housing cover

The Galley Tap – Limited Lifetime Warranty

1. GALLEY TAP LIMITED LIFETIME MECHANICAL WARRANTY —

Seller provides a Limited Lifetime Mechanical Warranty. Seller warrants its products, installed in a residential application, to be  free from manufacturing defects in materials and workmanship under normal usage for the useful life of the product. This Limited  Lifetime Mechanical Warranty is subject to the warranty conditions and limitations as set forth below.

2. GALLEY TAP LIMITED LIFETIME FINISH WARRANTY —

Seller provides a Limited Lifetime Finish Warranty. For the following Finishes: Polished Stainless Steel, Matte Stainless Steel, PVD  Satin Black Stainless Steel, PVD Gun Metal Gray™ Stainless Steel, PVD Polished Rose Gold Stainless Steel and PVD Brushed Gold  Stainless Steel, seller warrants its finishes, installed in a residential application, to be free from manufacturing defects in materials or  workmanship for the useful life of the product. Please refer to the Seller’s Care Instructions for the proper maintenance of Seller’s  finishes. This Limited Lifetime Finish Warranty is subject to the warranty conditions and limitations as set forth below.

3. WARRANTY CONDITIONS AND LIMITATIONS —

Seller’s Mechanical and Finish warranties are non-transferable and are strictly limited to products correctly installed using our  installation instructions and used in a residential environment. Mechanical or finish problems which result from abuse, misuse,  improper installation, improper maintenance, (including not properly winterizing the Tap in outdoor installations), improper  cleaning, proximity to bodies of saltwater, or accidental damage such as scuffs and scratches are not covered by this warranty. Seller  does not assume liability for labor charges, removal and reinstallation expenses, freight or postage charges, or injuries resulting from a defective product. This warranty does not allow recovery of incidental or consequential damages such as loss of use,  property damage, or any other consequential damage and Seller accepts no liability for such damage. Seller does not assume any  responsibility other than to repair or replace the defective part(s) after Seller, upon its examination, has determined the product to  be defective and the defective part(s) are covered by the Limited Lifetime Warranty expressed in this warranty. Whether to repair or  replace the product shall be at the sole election of the Seller. In no event shall the liability of The Galley exceed the purchase price  of the Tap. The use of Plumber’s Putty will void this warranty. A non-corrosive epoxy silicone sealing compound may be used. Seller  hereby disclaims all other warranties, expressed or implied, other than those set forth in this warranty. Some states do not allow  the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

4. CARE AND MAINTENANCE —

For care and maintenance instructions of all Galley products, please refer to the Use and Care section on thegalley.com.

5. WARRANTY CLAIMS —

For warranty service and to purchase replacement parts, please contact the Customer Service team. To arrange for service under  warranty, please prepare the following information:

1. Product model

2. Installation date

3. A description of the problem

The Galley range of goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled  to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are  entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

CONTACT US

Website www.winningappliances.com.au/s/services

Email  service@winning.com.au

Phone Mail +61 2 9694 0300

Winning Appliances Pty Limited ACN 002 193 688  20A Danks Street

Redfern NSW 2016

You must retain your original proof of purchase. Failure to produce proof of purchase when requested may, at The Galley, LLC’s discretion,  invalidate your claim.

The warrantor is:

The Galley, LLC.

Attn: Warranty Claims 12626 South Memorial Drive Bixby, OK 74008

USA

Australian Representative:

Winning Appliances Pty Limited ACN 002 193 688 20A Danks Street

Redfern NSW 2016

+61 2 9694 0300

Winning.com.au

Please include the original receipt with a description of the problem, model number, store, date of purchase, your name, address and  telephone number.

Replacement parts can be ordered from The Galley, LLC customer service. Email Service@Winning.com.au or call +61 (0) 2 9694 0300.

References

• THE GALLEY® | REINVENT YOUR KITCHEN
• Winning Group | We deliver inspiration
• Winning Appliances | Kitchen & Laundry Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>