CREATE Flowood Stylance Ceiling Fan User Manual

FLOWOOD STYLANCE
CEILING FAN VENTILADOR DE TECHO
USER MANUAL

Thank you for choosing our ceiling fan. Before using the appliance, and to ensure the best use, carefully read these instructions. The safety precautions enclosed herein reduce the risk of death, injury, and electrical shock when correctly adhered to. Keep the manual in a safe place for future reference, along with the completed warranty card, purchase receipt, and package. If applicable, pass these instructions on to the next owner of the appliance. Always follow basic safety precautions and accident-prevention measures when using an electrical appliance. We assume no liability for customers failing to comply with these requirements.

PARTS LIST

Carefully open the packaging and remove all the items included. Place them on a carpet or a big piece of plastic to avoid any damage. Check that all the items listed below have been included.

SAFETY INSTRUCTIONS

When using any electrical appliance, basic safety precautions should always be observed.
Read this entire manual carefully before beginning installation. Save this instruction.

• Use only original replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these instructions, and use only the hardware supplied.
• To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
• To reduce the risk of personal injury, do not bend the blade attachment system when installing, balancing, or cleaning the fan.
• Never insert foreign objects between rotating fan blades.
• To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state speed control with this fan. Use only original speed controls.
• This appliance can be used by children aged 8 years old and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Close supervision is necessary when any appliance is used by or near children.

NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense and caution are necessary factors in the installation and operation of this fan.

INSTALLATION INSTRUCTIONS

• Mark the correct position of the holes and fix the ceiling bracket using the screws with metal anchors or screws and washers suitable for the type of ceiling chosen.
• Check the correct installation of the bracket before hanging the fan. This plate must support the full weight of the fan.

INSTALLATION PREPARATION

• To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 2.3 m from the floor and 76 cm from any wall or obstruction.
• Be sure the outlet box is securely attached to the building structure and can support the full weight of the fan.

PREPARING THE FANSITE

Choose the suspension bar that best suits your situation: it has a 15 cm and a 25 cm suspension bar.
Remove the bar bolt, remove the pin, and pass the canopy (roof trim) and the engine canopy through the suspension bar. Next, route the fan motor cables through the inside of the suspension bar. Tighten the suspension bar to the engine and insert the bolt and pin.

Standard Mounting hangs from the ceiling by a downrod.
Angled Mounting is recommended for a vaulted or angled ceiling.

INSTALLING THE HANGER BRACKET

Please, drill an 8 mm diameter hole in the concrete ceiling, and insert the bolt. Then, align the bracket with the hole and tighten it with a nut.

ASSEMBLING AND HANGING THE FAN

Tip: To prepare for threading electrical wires through the downrod, apply a small piece of electrical tape to the ends of the electrical wires. This will keep the wires together when threading them through the downrod.

• Loosen the fixing screws and nut at the top of the motor housing. Remove the pin and bolt from the downrod (if you have not already done so). Slide the downrod through the canopy.
• Tread electrical wires through the downrod and pull extra wire slack from the upper end of the downrod.
• Place the downrod into the motor housing yoke and reinsert the pin and bolt that were previously removed. Tighten the fixing screws and nut securely.
•  Lower the canopy to the motor housing.

REMOTE CONTROL

1.  **Light
2. **Light intensity control
3. Fan intensity control
4. Timer
5. Batteries (2 x AAA)
6. **Colour temperature control
7. ON / OFF button

** Function only available when having the LED plate installed.

REMOTE CONTROL CONNECTION

Make the connection between the receiver cables and the fan motor cables following the color indications. Make sure the connection is tight.

CANOPY ASSEMBLY

• Raise the canopy to the hanger bracket, aligning loosened screws in the hanging bracket with slotted holes in the canopy.
• Twist the canopy to lock. Re-insert the screws and secure all the screws with a screwdriver.
• With a hanging bracket secured to the outlet box and able to support the fan, you are now ready to hang your fan.
• Grab the fan firmly with two hands. Slide downrod through the opening in the hanging bracket and let the hanging ball rest on the hanging bracket.
• Turn the hanging ball slot until it lines up with the hanging bracket tab.

Tip : Seek the help of another person to hold the stepladder in place and to lift the fan up to you once you are set on the ladder.

BLADES ASSEMBLY

Align the holes on the blade holder with the holes on the blades and the motor body and screw them in place, but don’t tighten them until they are all placed and screwed in. Tip: To save time, you can fit the washers on each screw prior to installing the blades.

CONNECTIONS PANEL ASSEMBLY

Attach the connections plate up to the bottom of the fan by inserting the set screw heads into the keyhole slots. Rotate them to place and tighten them to secure the plate.
CEILING FAN WITH LED LIGHT
LED LIGHT PANEL AND LAMP SHADE ASSEMBLY

Connect the single-pin plugs of the connections plate with the ones on the LED panel. The LED panel is magnetized so it will be attached to the connections panel just by placing them together.
Note: While installing or removing the LED plate, please keep the insulation pads intact carefully. Turning the set screws over-tightly or fast will damage the insulation pads.
Screw the lampshade back to the connections plate.

CEILING FAN WITHOUT LED LIGHT

DECORATIVE COVER ASSEMBLY
Once the connections plate has been assembled and secured, screw the decorative cover back to the connections plate using the central screw.
CHECK THE INSTALLATION

• Check the correct operation of the ceiling fan, checking that no strange movement or misalignment is observed in any part of the fan.
• In the event that some kind of hum/vibration can be seen, you can proceed to adjust the blades with the shooting kit.
• This kit has self-adhesive weights and “u” shaped clips.
• Turn off the ceiling fan.
• You can put the clip in the center of any blade and check if the vibration decreases.
• Turn on the fan and check. If no change is seen, turn off the fan and add another clip to a different blade or use the adhesive weights.

In compliance with Directives: 2012/19/EU and 2015/863/EU on the restriction of the use of dangerous substances in electric and electronic equipment as well as their waste disposal. The symbol with the crossed dustbin shown on the package indicates that the product at the end of its service life shall be collected as separate waste. Therefore, any products that have reached the end of their useful life must be given to waste disposal centers specializing in separate collection of waste electrical and electronic equipment, or given back to the retailer at the time of purchasing new similar equipment, on a one for one basis. The adequate separate collection for the subsequent start-up of the equipment sent to be recycled, treated, and disposed of in an environmentally compatible way contributes to preventing possible negative effects on the environment and health and optimizes the recycling and reuse of components making up the apparatus. Abusive disposal of the product by the user involves the application of administrative sanctions according to the laws.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>