KLARSTEIN 10013323 Powericer XL Ice Cube Maker Instruction Manual

June 5, 2024
Klarstein

POWERICER
10013323, 10013324
10013325, 10036152
www.klarstein.com

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damage. We assume no liability for damage
caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10036152

TECHNICAL DATA

Item number 10013323 10013324 10013325
10036152
Power supply 220-240 V — 50-60 Hz
Power consumption 145 W 160 W 260 W
Dimensions 380x477x590 mm 420x514x655 mm 498x604x831 mm

SAFETY INSTRUCTIONS

  • Check that the mains voltage corresponds to the rating of the appliance before operating.
  • Use handles or knobs when moving. Place on a flat stable surface for use. Do not use outdoors.
  • Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
  • Unplug from socket outlet when not in use.
  • To protect against electric shock, do not immerse the cord or plug in water or any other liquid.
  • The use of accessory attachments not recommended by the appliance manufacturer may cause injury.
  • Do not locate this appliance immediately below a socket outlet.
  • Do not allow the cord to overhang the countertop where it can be easily pulled by children.
  • Do not use this appliance for anything else other than its intended use.
  • Do not overfill as this may cause a hazard. Ensure the lid is closed when in operation
  • To remove the plug from the outlet, do not pull on the supply cord. Grasp the plug firmly and pull to remove it.
  • No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling. This appliance is for household use only
  • This appliance is not intended to be operated by means of an external timer or separate remote control system.
  • This appliance is not intended to be immersed in water.
  • If the supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a similarly qualified person in order to avoid a hazard.
  • Please according to local regulations regarding disposal of the appliance for its flammable blowing gas.
  • Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
  • Fill with potable water only.
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

This appliance contains the coolant isobutane (R600a), a natural gas that is environmentally friendly. Although it is flammable, it does not damage the
ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor, you might be able to hear the coolant flowing around the system. This is unavoidable and does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and setting up of the appliance so that no parts of the cooling system are damaged. Leaking coolant can damage the eyes.

WARNING
Danger from fire/flammable materials. Please observe the local regulations for the disposal of units with flammable refrigerants and gases.

  • Keep ventilation openings in the unit housing free of obstacles.
  • Do not damage the refrigerant circuit.
  • Do not use any mechanical devices or other means to accelerate the defrosting process or the ice recovery process.
  • Do not use other types of electrical appliances inside the ice cube machine.

Special Notes

  • When positioning the unit, make sure that the power cord is not pinched or damaged.

  • Make sure that there are no multiple sockets or power supplies on the back of the unit.
    To avoid contamination of food, please follow the instructions below:

  • Regularly clean surfaces that may come into contact with food. Clean the water drain regularly.

  • If the appliance contains a water tank, clean it if it has not been used for 48 hours.
    Rinse the tank if no water has been removed for 5 days.

WARNING
When using, servicing, and disposing of the unit, pay attention to the left symbol on the rear of the unit or on the compressor. This symbol warns of possible fires. There are flammable substances in the refrigerant lines and in the compressor. Keep the appliance away from sources of fire during use, maintenance, and disposal.

PRODUCT DESCRIPTION

Item number 10013323

KLARSTEIN 10013323 Powericer XL Ice Cube Maker -
DESCRIPTION

KLARSTEIN 10013323 Powericer XL Ice Cube Maker -
Function

1 Power Switch 2 Display panel
3 Front Panel 4 Door
5 Ice Bouncing Shelf 6 Ice Storage Container
7 Ice Lever Sensor 8 Power Cord
9 Water Inlet Valve 10 Drainage Tube
11 Feet 12 Drainage valve

ACCESSORIES

KLARSTEIN 10013323 Powericer XL Ice Cube Maker -
ACCESSORIES

USE AND OPERATION

  1. Unpack the Ice Baby from its carton, then remove the ice scoop, inlet/outlet tubes, and sealing washers from the container in the icemaker where they are stored for transit.

  2. Position the Ice Baby in a well-ventilated place, leaving at least a 150 mm gap between the ice maker and the walls/ceiling, etc. The ice maker must be level and situated away from any heat source.

  3. Attach one end of the ∮14mm flexible plastic corrugated pipe to the water outlet on the back of the machine. The other end of the pipe should be inserted into a waste pipe or a suitable container for the collection of the wastewater.

  4. Connect the 3/4” water inlet hose supplied with the ice maker to a drinking water supply and then connect the other end to the water inlet on the back of the machine.
    When connecting this hose, use the sealing washers supplied with the Ice Baby to eliminate the risk of a water leak.
    Note: The minimum inlet water pressure is 1.5 bar. The maximum inlet water pressure is 5 bar.

  5. Plug the power lead into the supply socket, then press the green on/off switch on the ice machine to start it – the green „run“ light will be lit. The Ice Baby will start to operate.

  6. The operation of the Ice Baker is completely automatic. water inlet, ice making, ice transfer, and ice storage.

  7. If the storage container is full, the „ice full“ indicator on the display panel will be lit, and the ice machine will stop automatically. Remove the ice from the storage container, wait for five minutes, then restart the ice maker.

  8. Should the water supply be restricted or fail, the „water low“ LED will be lit. The ice maker will stop automatically. When the water supply is restored, wait for at least five minutes, then restart the unit.

Important Notes on Use

  • If the compressor stops for any reason such as water shortage, too much ice, power off etcetera, don‘t restart it right away. You can restart it after 5 minutes in order to protect the compressor.
  • Check the connectors of the water inlet and outlet, tubes, and drain regularly for surplus water that may be present.
  • When plugging in or unplugging, the plug should be held by hand and the wires should not be dragged heavily.

CARE AND CLEANING

  • Always switch off and disconnect the power supply before cleaning
  • Warm, soapy water is recommended for cleaning. Cleaning agents may leave harmful residues. Do not wash the base unit, instead wipe the exterior with a damp cloth. Do not immerse in water, or use steam/jet washers to clean the unit.
  • Check regularly the connectors of the water inlet and outlet tubes and drain the little surplus water that may leak.
  • Clean the water filter regularly with a small brush, particularly in hard water areas. The water filter is located just inside the water inlet at the back of the appliance.
  • Replace any unused water in the tank at least once every 24 hours.
  • The inner removable parts and water tank should be cleaned regularly.

Special Note on the Item number 10013323
If the ice maker will be unused for long periods, please screw off the plastic drainage connector screw (12) on the back of the unit in order to drain the surplus water in the water groove, then screw it back on. Wipe the inner liner of the ice storage container with a clean cloth.

TROUBLESHOOTING

Problem

|

Possible Cause

|

Suggested Solution

---|---|---
The unit does not work.| The voltage is out of the limit.| Stop the ice maker and restart it until the voltage is normal.
The ambient temp is lower than 10°C.| Try again when the ambient temperature is higher than 10°C.
The water shortage indicator lights are on.| Water shortage from the water supply system.| Check the water supply. If it is OK, restart the unit.
Water valve damaged.| Check the water valve.
Tap water pressure too low.| Be sure the tap water pressure is higher than 1 kg/cm2.
The compressor doesn’t work.| Water shortage.| Check the water supply system (water valve and water supply tube).
The ice bucket is full.| Take out some ice.
The compressor works, but no ice is made.| Refrigerant leakage.| Refer all servicing to qualified service personnel.
---|---|---
The refrigerating system is blocked.
Ice is not dropping.| The water temperature or ambient temperature is too low.| Check whether the ambient temperature is too low (lower than 10 °C) or the water temperature is too low(lower than 7 °C)
The solenoid valve is damaged.| Refer all servicing to qualified service personnel.
Trouble indicator lights.| The water box does not tilt.|

Unplug the power, and check the tiling motor and relative system. 3-5 minutes later restart the machine.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals