Parrot Uncle F8279110V Modern Brushed Nickel Chandelier Ceiling Fan Instruction Manual
- June 16, 2024
- Parrot Uncle
Table of Contents
Parrot Uncle F8279110V Modern Brushed Nickel Chandelier Ceiling Fan
Instruction Manual
F8279110V
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Safety Information
-
To reduce the risk of electric shock, the electricity has been turned off at the circuit breaker or fuse box before begin.
-
All wiring must be in accordance with the National Electrical Code NASI/NFPA70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
-
The outlet box and support structure must be securely mounted and capable of reliably supporting 35lb.(15.9kg). Use only UL listed outlet boxes marked “Acceptable for Fan Support of 35lbs (15.9kg) or less.”
-
The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of the blades to the floor.
-
Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
-
Do not place objects in the path of the blades.
-
To avoid personal injury or damage to the fan and other items, please be careful when working around or cleaning the fan.
-
Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches.
Refer to the instructions packaged with the light kits and switches for proper assembly. -
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box. and the ungrounded conductor on the other side of the outlet box.
-
All setscrews must be checked and retightened where necessary before installation.
WARNING: TO reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
WARNING: To reduce the risk or fire or electric shock, do not use this fan with any solid-state speed control device.
WARNING: To avoid possible electric shock, turn the electricity off at the main fuse box before wiring. lf you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked”Acceptable for fan support of 35lbs. (15.9 kg) or less “and use the screws provided with the outlet box.
TECHNICAL INFORMATION
OPERATING YOUR FAN
SIZE OF PRODUCT
TROUBLESHOOTING GUIDE
1. FAN / REMOTE IS NOT WORKING
Ensure the remote is within the 20 foot range of the receiver
To reset the remote control: 1) Turn off power to fan using the wall switch or
circuit breaker.
2) Remove batteries from remote. 3) Wait 10 seconds. 4) Replace batteries and
turn power on
Check batteries to insure they are good and oriented correctly
Check to make sure the frequency switches (DIP Switches) from the remote to
the receiver are set to the same frequency
Check the main and branch circuit fuses or breakers
If using a Variable Speed Wall Switch,ensure it is specifically designed for
use with a ceiling fan.
Check the line wire connections to the fan and the switch wire connections in
the switch housing per the instructions
If fan still does not work, please contact Customer Service Support@Parrot
Uncle.com
2. THE FAN IS NOISY
Make sure all motor housing screws are tight
Make sure the screws that attach fan blade to motor are tight
Make sure the wire nut connectors are not rattling against each other or the
interior wall of the switch housing
Allow 24-hour break in period. Most noises associated with the new fan may
disappear during this time
if using a ceiling light kit,make sure the glassware is secured tightly
Make sure there is a short distance/gap from the ceiling to the top of the
canopy. The canopy should not touch the ceiling!
Make sure your ceiling box is secure and that the rubber insulating pads are
used between the mounting bracket and outlet box
3. THE FAN WOBBLES
Verify all blades and blade bracket screws are secure (most fan wobble
problems are caused by loose parts).Once fan is properly installed,run the
ceiling fan for 10 minutes to let the fan self-adjust.
If wobble occurs after running the fan for 10 minutes, verify blade level
using the following process:
a) select a point on the ceiling above the tip of one of the blades. Then
select the fan blade and measure from the center of the selected blade to
point on the ceiling. Rotate the fan until the next blade is positioned and
repeat the measurement using the same point from the ceiling for every blade.
Measurements should be within 1/8 inch.
b) If all deviation are less than 1/8 inch and the fan continues to wobble,
please contact Customer Service Support@parrot Uncle.com to order a
complimentary Blade Balancing Kit
-If all deviation are less than 1/8 inch and the fan continues to wobble, please contact Customer service Support@Parrot Uncle.com to order a complimentary Blade Balancing Kit.
4. LIGHT IS NOT WORKING
Loose electrical connections.
Shut off the branch circuit electricity at the fuse box or breaker panel and
check the LED light fixture assembly electrical connectors for proper
installation.
To reset the remote control: 1) Turn off power to fan using the wall switch or
circuit breaker. 2) Remove batteries from remote. 3) wait 10 seconds. 4)
Replace batteries and turn power on
AFTER INSTALLATION
Wobble
The fan blades have been adjusted in the factory to minimize any wobble
Note: c eiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet. If the fan was mounted rigidly to the ceiling, It would cause excess vibration. Movement of A few centimeters is quite acceptable and does not suggest any problem to reduce the fan Wobble: Please check that all screws which secured the mounting bracket and downrod are secure.
Balancing a wobbling ceiling fan:
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check
this level by electing a point on the ceiling above the tip of one of the
blades. Measure this distance. Rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. The distance deviation
should be equal within 1/8″(0.32cm).
3. If the blade wobble is still noticeable, Interchanging two adjacent (side
by side) blades can redistribute the weight and possibly result in smoother
operation.
Warning: To reduce the risk of personal injury, Do not bend the blade arm while installing, Balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.
Noise
When it is quiet (especially at night) you may hear occasional small noises.
This is normal.
Please allow a 24-hour “breaking-in” period, Most noises associated with a new
fan disappear during the time.
Care and cleaning
- Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn o ff electricity power before you clean your fan
- Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
- Motor has permanently lubricated ball bearing. No need to oil.
Note: Make sure the power is off at the electrical panel box before you attempt any cleaning or repairs.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>